1、 ETSI TS 129 389 V14.0.0 (2017-05) LTE; Inter-V2X Control Function Signalling aspects (V6); Stage 3 (3GPP TS 29.389 version 14.0.0 Release 14) TECHNICAL SPECIFICATION ETSI ETSI TS 129 389 V14.0.0 (2017-05)13GPP TS 29.389 version 14.0.0 Release 14Reference DTS/TSGC-0429389ve00 Keywords LTE ETSI 650 R
2、oute des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.et
3、si.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived differenc
4、e in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change
5、of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff
6、.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of
7、 ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2017. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade
8、Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. oneM2M logo is protected for the benefit of its Members GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI TS 129 389 V14.0.0 (2017-05)23GPP TS 29.389 version 14.
9、0.0 Release 14Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intelle
10、ctual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, includi
11、ng IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has
12、been produced by ETSI 3rd Generation Partnership Project (3GPP). The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or GSM identities. These should be interpreted as being references to the corresponding ETSI deliverables. The cross ref
13、erence between GSM, UMTS, 3GPP and ETSI identities can be found under http:/webapp.etsi.org/key/queryform.asp. Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in
14、 clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI TS 129 389 V14.0.0 (2017-05)33GPP TS 29.389 version 14.0.0 Release 14Contents Intellectual Property Rights
15、 2g3Foreword . 2g3Modal verbs terminology 2g3Foreword . 5g31 Scope 6g32 References 6g33 Definitions and abbreviations . 7g33.1 Definitions 7g33.3 Abbreviations . 7g34 General Description 7g34.1 Introduction 7g35 Procedure Description 7g35.1 Introduction 7g35.2 V2X Service Authorization 7g35.2.1 Gene
16、ral 7g35.2.2 Detailed behaviour of the V2X Control Function in the HPLMN 8g35.2.3 Detailed behaviour of the V2X Control Function in the VPLMN 9g36 Protocol Specification and Implementations 9g36.1 Introduction 9g36.1.1 Use of Diameter base protocol 9g36.1.2 Securing Diameter Messages 9g36.1.3 Accoun
17、ting functionality 9g36.1.4 Use of sessions 9g36.1.5 Transport protocol 10g36.1.6 Routing considerations . 10g36.1.7 Advertising Application Support 10g36.1.8 Diameter Application Identifier 10g36.1.9 Use of the Supported-Features AVP . 10g36.2 Commands 11g36.2.1 Introduction. 11g36.2.2 Command-Code
18、 values . 11g36.2.3 ProSe-Authorization-Request (PAR) Command 11g36.2.4 ProSe-Authorization-Answer (PAA) Command. 12g36.3 Information Elements . 12g36.3.1 General 12g36.3.2 V2X-Authorization-Data 13g36.3.3 V2X-Permission-in-VPLMN 14g36.3.4 V2X-Application-Server . 14g36.3.5 Application-Server 14g36.
19、3.6 Geographical-Information 14g36.3.7 OC-Supported-Features 14g36.3.8 OC-OLR . 14g36.3.9 DRMP . 14g36.4 Result-Code AVP and Experimental-Result AVP Values . 15g36.4.1 General 15g36.4.2 Success 15g36.4.3 Permanent Failures . 15g36.4.3.1 General 15g36.4.3.2 DIAMETER_ERROR_USER_UNKNOWN (5001) 15g36.4.
20、3.3 DIAMETER_ERROR_UNKNOWN_V2X_SUBSCRIPTION (5690) 15g36.4.3.4 DIAMETER_ERROR_V2X_NOT_ALLOWED (5691) 15g3Annex A (normative): Diameter overload control mechanism 16g3ETSI ETSI TS 129 389 V14.0.0 (2017-05)43GPP TS 29.389 version 14.0.0 Release 14A.1 General . 16g3A.2 Responding V2X Control Function b
21、ehaviour . 16g3A.3 Requesting V2X Control Function behaviour 16g3Annex B (Informative): Diameter overload node behaviour 18g3B.1 Message prioritization 18g3Annex C (normative): Diameter message priority mechanism 19g3C.1 General . 19g3C.2 V6 interfaces 19g3C.2.1 General 19g3C.2.2 V2X Control Functio
22、n behaviour . 19g3Annex D (informative): Change history 20g3History 21g3ETSI ETSI TS 129 389 V14.0.0 (2017-05)53GPP TS 29.389 version 14.0.0 Release 14Foreword This Technical Specification has been produced by the 3rdGeneration Partnership Project (3GPP). The contents of the present document are sub
23、ject to continuing work within the TSG and may change following formal TSG approval. Should the TSG modify the contents of the present document, it will be re-released by the TSG with an identifying change of release date and an increase in version number as follows: Version x.y.z where: x the first
24、 digit: 1 presented to TSG for information; 2 presented to TSG for approval; 3 or greater indicates TSG approved document under change control. y the second digit is incremented for all changes of substance, i.e. technical enhancements, corrections, updates, etc. z the third digit is incremented whe
25、n editorial only changes have been incorporated in the document. ETSI ETSI TS 129 389 V14.0.0 (2017-05)63GPP TS 29.389 version 14.0.0 Release 141 Scope The present document describes the Diameter-based interfaces between the V2X Control Function in the HPLMN and the V2X Control Function in the VPLMN
26、 (V6 interface). This specification defines the Diameter application for V6 reference points between the V2X Control Functions. The interactions between the V2X Control Functions are specified. The stage 2 description for V2X service features in EPS is specified in 3GPP TS 23.285 2. 2 References The
27、 following documents contain provisions which, through reference in this text, constitute provisions of the present document. - References are either specific (identified by date of publication, edition number, version number, etc.) or non-specific. - For a specific reference, subsequent revisions d
28、o not apply. - For a non-specific reference, the latest version applies. In the case of a reference to a 3GPP document (including a GSM document), a non-specific reference implicitly refers to the latest version of that document in the same Release as the present document. 1 3GPP TR 21.905: “Vocabul
29、ary for 3GPP Specifications“. 2 3GPP TS 23.285: “Architecture enhancements for V2X services; Stage 2“. 3 IETF RFC 6733: “Diameter Base Protocol“. 4 3GPP TS 33.210: “3G Security; Network Domain Security; IP Network Layer Security“. 5 IETF RFC 4960: “Stream Control Transmission Protocol“. 6 3GPP TS 29
30、.229: “Cx and Dx interfaces based on the Diameter protocol“. 7 IETF RFC 5234: “Augmented BNF for Syntax Specifications: ABNF“. 8 3GPP TS 23.003: “Numbering, addressing and identification“. 9 3GPP TS 29.228: “IP multimedia (IM) Subsystem Cx and Dx Interfaces; Signalling flows and Message Elements“. 1
31、0 3GPP TS 29.272: “Evolved Packet System; MME and SGSN Related Interfaces Based on Diameter Protocol“. 11 3GPP TS 29.329: “Sh Interface based on the Diameter protocol“. 12 IETF RFC 7683: “Diameter Overload Indication Conveyance“. 13 3GPP TS 29.336: “Home Subscriber Server (HSS) diameter interfaces f
32、or interworking with packet data networks and applications“. 14 3GPP TS 32.299: “Telecommunication management; Charging management; Diameter charging applications“. 15 IETF RFC 7944: “Diameter Routing Message Priority“. 16 3GPP TS 29.388: “V2X Control Function to V2X Control Function to Home Subscri
33、ber Server (HSS) aspects (V4)“. 17 3GPP TS 29.345: “Inter-Proximity-services (ProSe) Function signalling aspects“. ETSI ETSI TS 129 389 V14.0.0 (2017-05)73GPP TS 29.389 version 14.0.0 Release 143 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and de
34、finitions given in 3GPP TR 21.905 1 and the following apply. A term defined in the present document takes precedence over the definition of the same term, if any, in 3GPP TR 21.905 1. example: text used to clarify abstract rules by applying them literally. 3.3 Abbreviations For the purposes of the p
35、resent document, the abbreviations given in 3GPP TR 21.905 1 and the following apply. An abbreviation defined in the present document takes precedence over the definition of the same abbreviation, if any, in 3GPP TR 21.905 1. ProSe Proximity-based Services V2X Vehicle-to-Everything 4 General Descrip
36、tion 4.1 Introduction The V6 reference point is defined between a V2X Control Function in the HPLMN and a V2X Control Function in the VPLMN. The definition of the V6 reference points and related functionalities are given in 3GPP TS 23.285 2. As defined in 3GPP TS 23.285 2, the V6 reference point is
37、used for: - HPLMN control of service authorization for V2X. 5 Procedure Description 5.1 Introduction This subclause describes the Diameter-based V6 interface related procedures and Information elements exchanged between functional entities. In the tables that describe the Information Elements transp
38、orted by each Diameter command, each Information Element is marked as (M) Mandatory, (C) Conditional or (O) Optional in the “Cat.“ column. For the correct handling of the Information Element according to the category type, see the description detailed in clause 6 of the 3GPP TS 29.228 9. 5.2 V2X Ser
39、vice Authorization 5.2.1 General The V2X Service Authorization Procedure shall be used between the V2X Control Function in the HPLMN and the V2X Control Function in the VPLMN to obtain service authorization information for V2X services. The procedure shall be invoked by the V2X Control Function in t
40、he HPLMN of the UE and is used: ETSI ETSI TS 129 389 V14.0.0 (2017-05)83GPP TS 29.389 version 14.0.0 Release 14- to request service authorization information for V2X related to the UE from the V2X Control Function in the VPLMN; - to provide the V2X Control Function in the VPLMN with the UE identity
41、(IMSI or MSISDN) in order to allow to perform charging: This procedure is mapped to the commands ProSe-Authorization-Request/Answer (PAR/PAA) in the Diameter application specified in clause 6. Table 5.2.1-1 specifies the involved information elements for the request. Table 5.2.1-2 specifies the invo
42、lved information elements for the answer. Table 5.2.1-1: V2X Service Authorization Request Information element name Mapping to Diameter AVP Cat. Description UE Identity (See 3GPP TS 29.336 13) User-Identifier M This information element shall contain either the user IMSI, formatted according to 3GPP
43、TS 23.003 8, subclause 2.2, or the user MSISDN, formatted according to 3GPP TS 29.329 11. PLMN Id (See 3GPP TS 29.272 10) Visited-PLMN-Id M This IE shall contain the PLMN-Id (3GPP TS 23.003 8) of the network in which the V2X Control Function is located. Supported Features (See 3GPP TS 29.229 6) Supp
44、orted-Features O If present, this information element shall contain the list of features supported by the origin host. Table 5.2.1-2: V2X Service Authorization Answer Information element name Mapping to Diameter AVP Cat. Description Result (See 6.4) Result-Code / Experimental-Result M This IE shall
45、contain the result of the operation. The Result-Code AVP shall be used to indicate success / errors as defined in the Diameter Base Protocol. The Experimental-Result AVP shall be used for V6 errors. This is a grouped AVP which shall contain the 3GPP Vendor ID in the Vendor-Id AVP, and the error code
46、 in the Experimental-Result-Code AVP. The following errors are applicable: - User Unknown - Unauthorized Service - Unauthorized Service in this PLMN Supported Features (See 3GPP TS 29.229 6) Supported-Features O If present, this information element shall contain the list of features supported by the
47、 origin host. V2X Authorization Data (See 6.3.2) V2X-Authorization-Data C This Information Element shall contain the V2X authorization information of the user. It shall be present if success is reported. Editors Note: It is FFS on how to support charging for V2X service. 5.2.2 Detailed behaviour of
48、the V2X Control Function in the HPLMN The V2X Control Function in the HPLMN shall make use of this procedure to request service authorization information for V2X related to the UE from the V2X Control Function in the VPLMN. The V2X Control Function shall include in ETSI ETSI TS 129 389 V14.0.0 (2017
49、-05)93GPP TS 29.389 version 14.0.0 Release 14the request the UE identity (IMSI or MSISDN) and the PLMN-Id identifying the PLMN of the requesting V2X Control Function. When receiving a V2X Service Authorization response from the V2X Control Function in the VPLMN, the V2X Control Function in the HPLMN shall check the result code. If it indicates SUCCESS, the V2X Control Function shall merge with its own policy. 5.2.3 Detailed behaviour of the V2X Control Function in the VPLMN When receiving a V2X Service Authoriza
