FORD FLTM BN 154-1-2001 ABRASION RESISTANCE OF HOT STAMPED COATINGS (Replaces FLTM EU-BN 054-01).pdf

上传人:赵齐羽 文档编号:747280 上传时间:2019-01-14 格式:PDF 页数:3 大小:108.02KB
下载 相关 举报
FORD FLTM BN 154-1-2001 ABRASION RESISTANCE OF HOT STAMPED COATINGS (Replaces FLTM EU-BN 054-01).pdf_第1页
第1页 / 共3页
FORD FLTM BN 154-1-2001 ABRASION RESISTANCE OF HOT STAMPED COATINGS (Replaces FLTM EU-BN 054-01).pdf_第2页
第2页 / 共3页
FORD FLTM BN 154-1-2001 ABRASION RESISTANCE OF HOT STAMPED COATINGS (Replaces FLTM EU-BN 054-01).pdf_第3页
第3页 / 共3页
亲,该文档总共3页,全部预览完了,如果喜欢就下载吧!
资源描述

1、FORD LABORATORY TEST METHOD BN 154-01 Date 2001 O924 199201 14 ABRASION RESISTANCE OF HOT STAMPED COATINGS Action Revisions Revised Editorial - no technical change A. Cockman Application This test method is used to determine the abrasion resistance of hot stamped coatings, e.g. on plastic and/or woo

2、d parts. Apparatus and Materials Required Wear Tester According to BN 108-01 except as follows: Substitute the rubber diaphragm of the abrasion head by the edge abrasion clamp (special accessory to Stol1 Quartermaster Abrader - see suppliers technical brochure). Ab rada n t Duck cloth, reference num

3、ber 51 04450 Source: Messrs Bucher & Lohr 48 Bielefeld Herforter Strasse West Germany Trim Welt According to specification S-M98D4509-A. Conditioning and Test Conditions All test values indicated herein are based on material conditioned in a controlled atmosphere of 23 +I- 2 OC and 50 +I- 5 % relati

4、ve humidity for not less than 24 h prior to testing and tested under the same conditions unless otherwise specified. Procedure 1. Mount a section of trim welt 40 mm in length, covered with two layers of duck cloth and wrap in longitudinal direction - in the edge abrasion clamp (see Figure 1). Copyng

5、ht02001, Ford Global Technologies, Inc FORD LABORATORY TEST METHOD BN 154-01 2. Mount the assembly with the longer side parallel to the stroke direction of the abrasion head and tighten it with the ring clamp and lock the rotary motion pawl, avoiding any abrasive dust contamination. 3. Mount a hot s

6、tamped specimen under the abradant plate with the longer side or with its largest area parallel to the stroke direction. Carry out the test on a flat area of the specimen in order to obtain a smooth contact to the abradant. Load specimen with a total weight-force of 8.90 N. This total weight-force c

7、onsists of weight of specimen clamp, fastening screws, test specimen and additional weight. 4. Lower the abradant plate onto the abradant and abrade for the required number of cycles as stated in the relevant Material Specification. Note: If the abrasion test cannot be carried out on the actual part

8、 a hot stamped plane sample of minimum 10 x 60 mm size has to be tested for the Initial Laboratory Sample Report. Test panels shall be processed according to production conditions using the released base materials. Evaluation Examine for evidence of wear-through after the required abrasive cycles an

9、d compare with the master sample approved by the Product Engineering Materials Laboratory. Chemicals, materials, parts, and equipment referenced in this document must be used and handled properly. Each party is responsible for determining proper use and handling in its facilities. Page 2 of 3 Copyri

10、gWO2001, Ford Global Technologies, Inc FORD LABORATORY TEST METHOD BN 154-01 ABRASION RESISTANCE OF HOT STAMPED COATINGS 1) Additional Weight 2) Abradant Plate 3) Specimen Clamp 4) Specimen 5) Screws 6) Abradent 7) Edge Abrasion Clamp 8) Ring Clamp 9) Abrasion Head Page 3 of 3 CopyrigWO2001, Ford Global Technologies, Inc

展开阅读全文
相关资源
猜你喜欢
  • DIN 51366-2013 Testing of mineral oil hydrocarbons - Measurement of kinematic viscosity by means of the Cannon-Fenske viscometer for opaque liquids《矿物油碳氢化合物试验 采用Cannon-Fenske粘度计测量不.pdf DIN 51366-2013 Testing of mineral oil hydrocarbons - Measurement of kinematic viscosity by means of the Cannon-Fenske viscometer for opaque liquids《矿物油碳氢化合物试验 采用Cannon-Fenske粘度计测量不.pdf
  • DIN 51367-1991 Testing of metal working fluids determination of the stability of emulsified metal working fluids in hard water《金属切削冷却剂的试验 硬水中乳化金属加工冷却剂稳定性的试验》.pdf DIN 51367-1991 Testing of metal working fluids determination of the stability of emulsified metal working fluids in hard water《金属切削冷却剂的试验 硬水中乳化金属加工冷却剂稳定性的试验》.pdf
  • DIN 51368-1990 Determination of fraction separated by hydrochloric acid from water mix metal working fluids《金属加工冷却流体的试验 经盐酸分馏后从金属加工用水混合冷却流体中分离出部分的测定》.pdf DIN 51368-1990 Determination of fraction separated by hydrochloric acid from water mix metal working fluids《金属加工冷却流体的试验 经盐酸分馏后从金属加工用水混合冷却流体中分离出部分的测定》.pdf
  • DIN 51369-2013 Testing of cooling lubricants - Determination of the pH value of water-mixed cooling lubricants《冷却润滑剂试验 水混合式冷却润滑剂pH值的测定》.pdf DIN 51369-2013 Testing of cooling lubricants - Determination of the pH value of water-mixed cooling lubricants《冷却润滑剂试验 水混合式冷却润滑剂pH值的测定》.pdf
  • DIN 51371-2008 Liquid fuels - Determination of thermal stability of fuel oil EL《液体燃料 燃油EL热稳定性的测定》.pdf DIN 51371-2008 Liquid fuels - Determination of thermal stability of fuel oil EL《液体燃料 燃油EL热稳定性的测定》.pdf
  • DIN 51375-2-2001 Testing of lubricants - Determination of 1 2-ethanediol content of motor oils - Part 2 Gas chromatography《润滑剂检验 发动机油乙二醇(1 2)含量测定 气相层析法》.pdf DIN 51375-2-2001 Testing of lubricants - Determination of 1 2-ethanediol content of motor oils - Part 2 Gas chromatography《润滑剂检验 发动机油乙二醇(1 2)含量测定 气相层析法》.pdf
  • DIN 51378-1994 Testing of mineral oils determination of carbon-type composition《矿物油的检验 碳类成分的测定》.pdf DIN 51378-1994 Testing of mineral oils determination of carbon-type composition《矿物油的检验 碳类成分的测定》.pdf
  • DIN 5138-1973 Chisel handles《錾子手柄》.pdf DIN 5138-1973 Chisel handles《錾子手柄》.pdf
  • DIN 51380-2016 Testing of lubricants - Test for fuel diluent in used automotive engine oils - Gas chromatography method《润滑剂试验 汽车发动机燃油使用的燃料稀释剂的试验 气相色谱法》.pdf DIN 51380-2016 Testing of lubricants - Test for fuel diluent in used automotive engine oils - Gas chromatography method《润滑剂试验 汽车发动机燃油使用的燃料稀释剂的试验 气相色谱法》.pdf
  • 相关搜索

    当前位置:首页 > 标准规范 > 国际标准 > 其他

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1