1、ADAM OPEL AGTDCCentral LaboratoriesTECHN. LIEFERBEDINGUNGENFR WERKSTOFFEENGINEERINGMATERIAL SPECIFICATIONLIMITED USEQK 000326Polyacetal-HomopolymerisatPolyacetal-HomopolymerNote: This standard may be applied only for current programs. It is inactive for all future projects andwithout replacement.If
2、this product should be used for a new project, a Re-Certification according to GMW15702 is required.Hinweis: Diese Spezifikation darf nur noch fr laufende Projekte angewendet werden und ist fr allezuknftigen Projekte ohne Ersatz ungltig.Falls dieses Produkt fr ein neues Projekt zum Einsatz kommen so
3、ll, ist eine Neu-Zertifizierung nachGMW15702 erforderlich.Werkstoff: Polyacetal-HomopolymerisatMaterial: Polyacetal-HomopolymerKurzzeichen: POM Symbol:Verwendung: Spritzgietype mittlerer Viskositt zur Herstellung mechanisch be-lasteter technischer Teile.Application: Injection moulding type wih a med
4、ium viscosity type for manufacturingmechanically loaded technical parts .Handelsname: Delrin 500 (Standardtyp / Standard type)Trade Name: Delrin 500 P (mit Verarbeitungshilfsmitteln / with processing auxiliaryagents)Lieferant: Du Pont de Nemours (Deutschland) GmbH, D-6380 Bad HomburgSupplier:Lieferf
5、orm: GranulatForm of Delivery: GranulesAusfertigungs-Nr.:Issue: 5Datum:Date: 10/14Ausgefertigt:Prepared: JKGenehmigt:Approved: MKSeite vonPage 1 of 4Unbeschadet etwaiger durch den Abnehmer erfolgenden Stichprobenprfungen trgt der Lieferant die Verantwortung dafr, da die gelieferteWare die Opel-Zeich
6、nungsvorschriften erfllt. Ein Prfbericht mit zahlenmigen Ergebnissen aus Prfungen der Lieferung selbst ist bei jederBemusterung, Erstbelieferung und Ausfhrungsnderung mitzugeben.Despite spot checks possibly performed by Opel, it is the suppliers responsibility that the delivered parts are in line wi
7、th the Opel drawings.Deliveries of samples, first off-tool parts and parts, whose performance has been changed, must be accompanied by a test report showing thetest results in terms of figures.LBSP TL WS 1 11/95LIMITED USE QK 000326Ausfertigungs-Nr.:Issue: 5Datum:Date: 10/14Ausgefertigt:Prepared: JK
8、Genehmigt:Approved: MKSeite vonPage 2 of 4Forderungen / Requirementsa) zu dokumentierende Eigenschaften / values for documentationDichte DIN 53 479Density (1,41 0,02) g/cm3Elastizittsmodul aus dem DIN 53 4573-Punkt-BiegeversuchModulus of Elasticity by the3-Point-Flexural Test 2600 N/mm2Kerbschlagzhi
9、gkeit nach IZOD ISO 180 / 1ANotched Impact Strength to IZOD 6 kJ/m2Formbestndigkeit in der Wrme DIN ISO 306Temperature of Deflection underLoadVerfahren/Method B +90 CSchmelzindex DIN 53 735Melt Flow IndexMFI 190/2,16 (11,0 bis/to 17,0) g/10 minb) nur zur Information / only for informationStreckspann
10、ung )DIN 53 455,Tensile Strength at Yield 72 N/mm2 )Probekrper 3)Test piece 3,Reidehnung )v/speed =Elongation at Break 50 % )50 mm/minKerbschlagzhigkeit nach CHARPY ISO 179 / 2ANotched Impact Strength to CHARPY 8,5 kJ/m2Schmelztemperatur )DIN 53 736Melt Temperature 175 C )Verfahren B1)Method B1Vicat
11、-Erweichungstemperatur DIN 53 460Vicat Softening TemperatureVST/B/120 162 CThermischer Lngenausdehnungs- DIN 53 752koeffizientCoefficient of linear thermal expansion30C bis/to 60C 12,2 x 10-5 1/KLIMITED USE QK 000326Ausfertigungs-Nr.:Issue: 5Datum:Date: 10/14Ausgefertigt:Prepared: JKGenehmigt:Approv
12、ed: MKSeite vonPage 3 of 4Umweltschutz / Environmental Protectionnach/to QU 000 001 - Cadmium.Hinweise / ReferencesWeitere Informationen siehe QK 000 000.For further information refer to QK 000 000.Bemerkung / NoteAlle Probekrper werden im Spritzgieverfahren hergestellt. /All test pieces shall be ma
13、nufactured by injection moulding.Abfallbeseitigung / Waste DisposalGruppe D, Opel-Betriebsrichtlinie Nr. 440Achtung! Bei unkontrollierter thermischer Zersetzung Bildung von giftigen Abbauproduk-ten.Group D, Opel-Plant Directive No. 440Attention! Uncontrolled thermal decomposition gives poisonous decomposition products.LIMITED USE QK 000326LBSP TL 3 11/9522.10.2014 Limited Use StatusDatumDateBeschreibung / Description GeprftCheckedGenehmigtAppd.nderungen / RevisionsAusfertigungs-Nr.:Issue: 5Datum:Date: 10/14Ausgefertigt:Prepared: JKGenehmigt:Approved: MKSeite vonPage 4 of 4