1、 ENGINEERING STANDARDS Material Specification SUPERCEDED EDS-M-3302 Black Oxidation Finishes on Steels This standard may be applied only for current project. It is Superceded for all future projects and replaced by ISO 11408. H 1 1G Fp* Note: 8 E:48t G8 =9 7 FF7 957%L+ , FG P-P Program .Bd# ISO 1140
2、8 ) $4=F7 957F$ . Copyright 2011 General Motors Company All Rights Reserved April 2011 Originating Department: GM Korea Engineering Standards Page 1 of 4 Version : 3 1 Scope 1.1 Material Description. This standard specifies the black oxidation coating used by GM Korea Company (hereinafter referred t
3、o as the “GM Korea“). 1.1.1 Type and Use (Reference). 1 P7 1.1 8: 8-L C2e . 8 8t GM Korea Company (8F “$-1 ”( F )72P 17F# :0) 74 F18x +958p) =*F# H 1 1G Fp*7 $4F7 9IF$ . 1.1.1 9* -C 7$ (=l ). Table 1: Type and Use / E 1: 9* -C 7$ Type / 9* Base metal / 2: 07 38%P E:48x 957F$ . 2.1 17 E:4 / . None 2.
4、2 GM E:4 / . EDS-M-1101 EDS-T-7143 GMW3059 2.3 dA E:4 / . TMC003 Material Safety Data Sheet guidance documents GM KOREA ENGINEERING STANDARDS EDS-M-3302 Copyright 2011 General Motors Company All Rights Reserved April 2011 Page 2 of 4 Version : 3 3 Requirements 3.1 Coating. 3.1.1 The finishing accord
5、ing to this standard shall be the alkali coloring in principle. If the requirements for corrosion resistance in paragraph 3.3 are met, however, other finishing methods (e.g. temper color). * The alkali coloring method is to form an oxidation coating on the surface of parts in the high-temperature al
6、kali solution or mixed melt solution. 3.1.2 The appearance of coating formed by the alkali coloring method shall be black with gloss. 3.2 Post Treatment. To improve the corrosion resistance of the coating, appropriate anti corrosive shall be applied after coating. 3.3 Corrosion Resistance. There sha
7、ll be no occurrence of rust on 5 % or more of the effective surface of the test piece after testing for 12 hours according to EDS-T-7143. 3.4 Dimensional Tolerance. The dimensional deviation caused by this treatment shall be within the tolerance in the drawing. 3.5 Test. 3.5.1 All tests shall be per
8、formed at 235 E . 3.5.2 Test Sample. 3.5.2.1 In principle, test sample shall be taken from the products. However, in case it is impracticable to perform test on the product, general cold-rolled steel sheets SPCC, EDS-M-1101 may be substituted for the test piece. 3.5.2.2 The test sample shall be subj
9、ected to identical treatment with the manufacturing process of the products in principle. 3.5.3 Test Standards. EDS-T-7143: Method of Salt Spray Test. 3 7 1F 3.1 Fp* . 3.1.1 ., 7 &d* =*# 6?* =1-8x 8?8p) F! , 3.3 F8 !42e 9P* +9F+ dA =*- (78 88x 7 , F6* 72T8p) F$ . GM KOREA ENGINEERING STANDARDS EDS-M
10、3302 Copyright 2011 General Motors Company All Rights Reserved April 2011 Page 3 of 4 Version : 3 5.3 Inspection and Rejection. Samples of components or materials released to a GM material specification shall be tested for conformity with the requirements of this material specification and approved
11、 by the responsible Engineering department prior to commencement of delivery of bulk supplies. A new approval must be received for any changes, e.g., properties, manufacturing process, location of manufacture, etc. If not otherwise agreed, all testing and documentation normally required for initial
12、release must be completed. It is the responsibility of the supplier to inform the customer in a timely manner, without solicitation, and to include documentation of all modifications of materials and/or processes and to apply for a new release. If not otherwise agreed, all release tests shall be rep
13、eated and documented by the supplier prior to commencement of delivery of non-conforming bulk supplies. In individual cases, a shorter test can be agreed to between the responsible Engineering department and the supplier. 5.4 Initial Source Approval. No shipments shall be made by any supplier until
14、representative initial production samples have been approved by the appropriate Materials Engineering department(s) as meeting the requirements of this specification. 5.5 Material Safety Data Sheets/Safety Data Sheets (MSDS/SDS). For new product submissions, or when a change in chemical composition
15、of an existing product has occurred, a complete copy of the Material Safety Data Sheet/Safety Data Sheet must be submitted in compliance with the Globally Harmonized System of Classification and Labeling of Chemicals (GHS) requirements or other country-specific MSDS/SDS requirements. In addition, pr
16、oduct MSDS/SDS submissions must be in compliance with specific country General Motors TMC003 Material Safety Data Sheet/Safety Data Sheet guidance documents where available. 5.6 All materials supplied to this standard must comply with the requirements of GMW3059, Restricted and Reportable Substances
17、 for Parts. 6 Approved Sources Engineering qualifications of an approved source are required for this standard. Only sources listed in the GM Materials File under this standard number have been qualified by Engineering as meeting the requirements of this standard. For other GM locations, the respons
18、ible Engineering group should be contacted to obtain the approved source in that individual country. 5.3 1 -C -L)X . GM 8-LE:47 8F 9P%P .E8! 8*8 4G D8t ., 8-LE:47 9I%P 4G 8x 7 98x +94P6 F+ , 61 )= 987 :04 .2P8 388x -O6x6 F$ . &H88 , d# , 22e , 9P9 )9I ,* /D# 21: &%0 4)%P 6&F -8($ -P2%T 7 , 1)7 388x
19、O6x6 F$ . $* F84 6# F , 8-L958p) 4 4=8x F6 F$ . -$8 GE84 6# F , )=8# 38%L: 68t 9PE8 61 )= 987 +& F$- 4G 8x -L.) 3LFF 0* ,l2PGF6 F$ . 8. 77 86 :04 .2P7t )=888 F87 8F $%P : 4G 8x 44F 3L 8$ . 5.4 FF2P# 6| %P$ . 5.5 ,p:6|98.(8* / 6|98.(8* (MSDS/SDS). 49PE8 )= D# d97 )=%L# 9PE ! GF,p: 92e8 -%P 7 , GF ,p
20、 .* y E47 4F 2l 9G 43B (GHS) D# 5 :7!- ,p:6|98.(8* / 6|98.(8* 7 1F8x +9F# ,p:6|98.(8* / 6|98.(8* 9PF6+ F$ . 4958p) 9PE8 ,p:6|98.(8* / 6|98.(8*# GM8 ,p:6|98.(8* / 6|98.(8*7 4F :?8 TMC0038 7 1F8x :43LF6+ F$ . 5.6 ., E:47 9P4%P +& 8:&8t GMW3059 (8TF,p: 179P )8 9P* &d(6 F$ . 6 38 6= 8 E:48t 38%P 6=7 $4
21、F d3T95 :8x 7F$ . 8 E:47 8F d3T958 :8 7x*%P GM 88 +2l7 !7(%P 6=+8 8 E:48 7 1F8x 94A$ . $* :7!7 88?F GM 8 7 , F$- 4-) 38%P 6= 9I.(* 83LFd 88F2P# F$- :04 .2P7t GE8F6 F$ . GM KOREA ENGINEERING STANDARDS EDS-M-3302 Copyright 2011 General Motors Company All Rights Reserved April 2011 Page 4 of 4 Version
22、 3 7 Notes 7.1 Glossary. Not applicable. 7.2 Acronyms, Abbreviations, and Symbols. GHS Globally Harmonized System MSDS Material Safety Data Sheet SDS Safety Data Sheet 8 Coding System This standard shall be referenced in other documents, drawings, etc., as follows: 7 768 9I8 7.1 98,l 76 . F$-1F 68
23、 7.2 66 -C dGl . GHS Globally Harmonized System MSDS Material Safety Data Sheet SDS Safety Data Sheet 8 Ed - $* ,l2P! $+ &%72P ., E:48 87%T &# $80 M8 EdF$ . BOF (EDS-M-3302) Material Specification Number / 8: E:4 -Gl Black Oxidation Finishing / H 1 1G Fp* 9 Release and Revisions This standard was o
24、riginated in July 1994. It was first approved by Engineering Standard Committee in July 1994. It was first published in July 1994. 9 9P9I -C P9I 8)Y ., E:48t 1994 “x 7 87 E:4 -Gl4 .7 %L6 , d3TE:41,h7 8F 1994“x 787 38%L6$ . ., E:48t 1994“x 787 ) 9P9I / -PF%L6$ . Issue / P9I8)Y Publication Date / 38 88 Description (Organization) / 9PP9I76 (:04.2P ) 3 APR 2011 Apply new Engineering Standard Template. Superceded (Corrosion / Metallurgical Material Lab Team) / 4 d3TE:4 64 957 . F9I957 =* (28*4G D4 )
