1、P!EElA-A-231OAOctober 8,2002SUPERSEDINGA-A-231OSeptember 27,1985COMMERCIAL ITEM DESCRIPTIONFILE, HAND (AMERICAN PATTERN), CROSSCUTThe General Services Administration has authorized the use of this commercial item descriptionby all federal agencies,1. SCOPE. This commercial item description covers ha
2、nd tiles used for sharpening crosscut saws of the“Great American” style.2. CLASSIFICATION. Not Applicable3. SALIENT CHARACTERISTICS.3.1 Desizrr. The tile shall have uniform width and thickness from heel to point. The two sides equal inwidth from heel to point and at equal angles with the median long
3、itudinal plane of the file, All cornersstraight and parallel from heel to point. Back rounded for tiling gullets. Single-cut (one set of parallelcuts on the surface) on back, sides and bottom edge. The file dimensions shall conform to section 3.23.2 Dimensions.Dimensions at Largest Allowable Allowab
4、leLength Section Number of Teeth Distortion WarpageA B Min Max Max MaxIn In In Per In Per In In Degree8 11/16 9/32 42 48 0.010 3Length Dimensions: Measured from the point (ffee or front end) to the heel and have a toleranceof +/- 1/8”.Tolerance: Width (A) plus or minus 1/16“; TMckness (B) files 6“ i
5、n length +/- 1/32” JFiles over 6“ in length +/- 1/16.Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any other datae which may improve this document should be sent to: General Services Administration, Federal SupplyService, Hardware SuuerStore (6FEE), 1500 E. Ban
6、nister Rd Bldg. #6, Kansas City, Missouri 64131.FSC 5110Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-23 10A3.3 Material. The file shall be of a carbon alloy steel.3.4 Shall be of a conventional shape and size suitable for attachment to a wood
7、handle.Tempered to a maximum hardness of 45 on the Rockwell C scale when tested per ASTM El 8. It shall obe measured at a point approximately midway of its length and width.3.5- Shall be designed for fast cutting and minimize clogging. Uniformly cut or etched and ofuniform height throughout the full
8、y cut portion. Cutting surfaces shall be hardened to a uniformhardness. The distrmce between the heel and point of the file, excluding the tang, shall be hardened tonot greater than 68 nor less than 64 on the Rockwell C scale when tested per ASTM E 18. The file shallbe free from decarburization and
9、brittleness.3.6 Marking. The file shall be marked with the name of the manufacturer or with a trademark of suchknown character that the source of manufacture maybe readily determined.3.7 Workmanship. The teeth of the file shall be well-defined, sharp, and uniform in height and formThere shall be no
10、evidence of rust or other defect which may impair serviceability, durability orappearance.4. REGULATORY REQUIREMENTS.4.1 Recovered Materials. The offeror/contractor is encouraged to use recovered materials to themaximum extent practicable, in accordance with paragraph 23.403 of the Federal acquisiti
11、on Regulation(FAR).4.2 Metric uroducts. Products manufactured to metric dimensions will be considered on an equal basis a71with those manufactured using inch-pound units, provided they fall within the tolerances specified(using conversion tables contained in the latest revision of Federal Standard 3
12、76) and all otherrequirements of this document are met. If a product is manufactured to metric dimensions and thosedimensions exceed the tolerances specified in the inch- pound units, a request should be made to thecontracting officer to determine if the product is acceptable.5, PRODUCT CONFORMANCE.
13、5.1 Product Conformmce. The product provided shall meet the salient characteristics of thisCommercial Item Description, conform to the producers own drawing, specifications, standards, andquality assurance practices, and be the same product offered for sale in the commercial market, Thegovernment re
14、serves the right to require proof of such conformance.5.2 Resuonsibilit for Inspection. Unless otherwise specified, the contractor is responsible for theperformance of all inspection requirements and may use any commercial facilities (inchrding thecontractors own facilities) suitable for performance
15、 of the inspection requirements, unless disapprovedby the Government. The Government reserves the right to perform any of the inspections deemednecessary to assure the item conforms to the specified requirements.6. PACKAGING. Preservation, packaging and marking shall be as specified in the contracto
16、r order.7. NOTES. This section contains information of a general or explanatory nature that is not mandatory. a712Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-IA-A-23 10A7.1 Source of Documents.American Society for Testing and Materials (ASTM); PO
17、 Box C700, West Conshohocken, PA 19428-2959.Federrd Acquisition Regulation (FAR): Government Printing Office, Superintendent of Documents,Washington DC. 20401-9371.GSA Specification Section (3FP-E), Suite8100, 470 LEnfant Plaza, SW, Washington, DC 20407.7.2 Ordering data. Purchasers should select th
18、e preferred options permitted herein rmd should include thefollowing information in procurement documents.a. Title, number, and date of Commercial Item Description.b. Classc. Dimensionsd. Packaging requirements.7.3 National Stock Numbers (AWNS). A list of NSNs assigned that correspond to this CID, T
19、he listmay not be indicative of all possible NSNS associated with the CID.NSN Length Dimensions of Cross-SectionA BIn In In5110-00-204-0616 8 11/16 9/327,4 Key words. File, Hand (American Pattern), CrosscutMILITARY INTERESTS: Preparing Activity:NONE: DoD has no registered interest GSA-FSSin revisions and amendments to thisCommercial Item Description until further notice.3Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
