1、F=lA-A-2314Aa71 October 8,2002SUPERSEDINGA-A-2313September.27, 1985COMMERCIAL ITEM DESCRIPTIONFILE, HAND (AMERICAN PATTERN), KNIFEThe General Services Administration has authorized the use of this commercial item descriptionby all federal agencies.1. SCOPE. This commercial item description covers ha
2、nd files used for filing acute angles such as inkeyways and slots.2. CLASSIFICATION.Type I Bastard-cutType II Second-cutType 111 Smooth-cut3. SALIENT CHARACTERISTICS.a71 3.1 Desire. The file shall have a knife cross-section with an included angle between sides of 9-15,inclusive. Each wide flat doubl
3、e-cut (two sets of parallel cuts on the surface, one set crossing the other.)the thin flat side shall be single-cut (one set of parallel cuts on the surface). The back shall be single-cutor smooth (safe). The file shall be furnished in three types and Thickness (B) files 6“ in length +/- 1/32”lFiles
4、 over 6“ in length +/- 1/16.3.3 Material. The file shall be of a carbon alloy steel.3.4 Shall be of a conventional shape and size suitable for attachment to a wood handle.Tempered to a maximum hardness of 45 on the Rockwell C scale when tested per ASTM El 8. It shallbe measured at a point approximat
5、ely midway of its length and width.3.5 = Shall be designed for fast cutting and minimize clogging. Uniformly cut or etched and ofuniform height throughout the fully cut portion. Cutting surfaces shall be hardened to a uniformhardness. The distance between the heel and point of the file, excluding th
6、e tang, shall be hardened tonot greater than 68 nor less than 64 on the Rockwell C scale when tested per ASTM E 18, The tile shallbe free from decarburization and brittleness.3.6 Marking. The tile shall be marked with the name of the manufacturer or with a trademark of suchknown character that the s
7、ource of manufacture maybe readily determined.3.7 Workmanship. The teeth of the tile shall be well-defined, sharp, and uniform in height and formThere shall be no evidence of rust or other defect which may impair serviceability, durability orappearance.Provided by IHSNot for ResaleNo reproduction or
8、 networking permitted without license from IHS-,-,-A-A-23 14A4. REGULATORY REQUIREMENTS.4.1 Recovered Materials. The offeror/contractor is encouraged to use recovered materials to themaximum extent practicable, in accordance with paragraph 23.403 of the Federal acquisition Regulation(FAR).4.2 Metric
9、 uroducts. Products manufactured to metric dimensions will be considered on an equal basiswith those manufactured using inch-pound units, provided they fall within the tolerances specified(using conversion tables Contained in the latest revision of Federal Standard 376) and all otherrequirements of
10、this document are met. If a product is manufactured to metric dimensions and thosedimensions exceed the tolerances specified in the inch- poundunits, a request should be made to thecontracting officer to determine if the product is acceptable.5. PRODUCT CONFORMANCE.5.1roduct Conformrmce. eproduct pr
11、ovided shdlmeet tiesalient characteristics of thisCommercial Item Description, conform to the producers own drawing, specifications, standards, andquality asswmce practices, mdbethe smeproduct offered forsale inthecommercid mwket. Thegovernment reserves the right to require proof of such conformance
12、5.2 Responsibility for Inspection. Unless othemise specified, thecontractor irresponsible fortheperformance of all inspection requirements and may use any commercial facilities (including thecontractors own facilities) suitable for performance of the inspection requirements, unless disapprovedby th
13、e Government. The Government reserves the right to perform any of the inspections deemednecessary to assure the item conforms to the specified requirements.6. PACKAGING. Presemation, packaging mdmabng shall beasspecified intie contract ororder.,7. NOTES. This section contains infomation ofagenerd or
14、explmato natirethat isnot mandatory.7.1 Source of Documents.American Society for Testing and Materials (ASTM), PO Box C700, West Conshohocken, PA 19428-2959.Federal Acquisition Regulation (TAR): Govenyuent Printing OffIce, Superintendent of Documents,Washington DC. 20401-9371.GSA Specification Secti
15、on (3FP-E), Suite 8100,470 LEnfant Pla, SW, Washington, DC 20407.7.2 Orderiruz data. Purchasers should select the preferred options permitted herein and should include thefollowing information in procurement documents.:.c.d.Title, number, and date of Commercial Item Description.TypeDimensionsPackagi
16、ng requirements.3Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-23 14A7.3 National Stock Numbers (N SNS). A list of NSNs assigned that correspond to this CID. The listmay not be indicative of all possible NSNs associated with the CID.NSN Length
17、Dimensions of Cross-SectionA B cIn In In InType I - Bastard-cut5110-00-234-6563 6 5/32 1/16 11/165110-00-234-6566 8 13/16 1/16 7/85110-00-234-6569 10 1/4 1/16 1-1/16Type 11- Second-cut5110-00-238-7866 4 7/64 1/32 15/325110-00-203-4948 6 5/32 1/16 11/165110-00-234-6567 8 3/16 1/16 7/85110-00-234-6570
18、 12 1/4 1/16 1-1/16Type III - Smooth-cut5110-00-203-4552 6 5/32 1/16 11/165110-00-203-4553 8 3/16 1/16 7/85110-00-203-4554 10 114 1/16 1-1/167.4 Key words. File, Hand (American Pattern), KnifeMILITARY INTERESTS: Preparing Activity: aNONE: DoD has no registered interest GSA-FSSin revisions and amendments to thisCommercial Item Description until further notice.4Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
