1、A.C.N. 006 893 232Holden LimitedEngineering DepartmentMATERIAL SPECIFICATIONNUMBERSHEETRELEASEREVISION:HN 22401 of 4October, 1996February, 2000NAME: ADHESIVE TAPE, NONWOVEN, SOUND ABATEMENTTHIS DOCUMENT MUST NOT BE REPRODUCED. IF USED IN RELATION TOTHE COMPANYS PRODUCTS THE RECIPIENT IS RESPONSIBLE
2、TO CONFIRMTHE DOCUMENT ISSUE DATE IS STILL VALID.FORM : I:LABRTORYFORMSTDMATSPEC.DOC1. SCOPEThis specification describes the physical and performance properties of a nonwovensound abatement tape. The tape consists of a nonwoven material coated on oneside with a pressure sensitive adhesive.1.1 The ta
3、pe is used for sound abatement applications where two similar ordissimilar substrate materials come into contact causing rubbing, chaffing,itching, chattering, or squeaking noise. A typical application would bebetween A/B/C pillar mouldings and instrument panel assemblies.1.2 Type tape is a lower co
4、st alternative to flock tape, with lower abrasionresistance. Type tape is capable of conforming to irregular surfaces withexcellent abrasion resistance.2. REFERENCESGM1000M ASTM D 1004 SAE J1351 ASTM D 1000SAE J369 SAE J1756 HN 10003. REQUIREMENTS3.1 PropertiesRefer to Table 13.2 Shelf LifeMaterial
5、shall pass all requirements of this specification after ageing materialin the original container 90 days at 35 oCA.C.N. 006 893 232Holden LimitedEngineering DepartmentMATERIAL SPECIFICATIONNUMBERSHEETRELEASEREVISION:HN 22402 of 4October, 1996February, 2000NAME: ADHESIVE TAPE, NONWOVEN, SOUND ABATEME
6、NTTHIS DOCUMENT MUST NOT BE REPRODUCED. IF USED IN RELATION TOTHE COMPANYS PRODUCTS THE RECIPIENT IS RESPONSIBLE TO CONFIRMTHE DOCUMENT ISSUE DATE IS STILL VALID.FORM : I:LABRTORYFORMSTDMATSPEC.DOC3. REQUIREMENTS (continued)3.3 ConstructionThe size of the product shall conform to the following:TABLE
7、 2Description Type Type Total Thickness, min 0.3 mm 0.42 mmMaterial Type Polyester PolyurethaneConstruction Non-Woven Non-WovenColour Dark Gray/Black BlackPressure SensitiveAdhesiveAcrylic Acrylic3.4 PackagingTape to be furnished in evenly and uniformly wound rolls on suitable coreswith silicone tre
8、ated paper or polyethylene release liner (if applicable), easilyremovable with no separation of material.4. OTHER TESTS MAY BE REQUIRED TO VALIDATE THE SPECIFIC APPLICATION5. APPROVAL, INSPECTION AND REJECTIONRefer HN 1000, Clauses A and C.6. HAZARDOUS MATERIALSRefer HN 1000, Clause H.7. RESTRICTED
9、CHEMICALSRefer HN 1000, Clause J.A.C.N. 006 893 232Holden LimitedEngineering DepartmentMATERIAL SPECIFICATIONNUMBERSHEETRELEASEREVISION:HN 22403 of 4October, 1996February, 2000NAME: ADHESIVE TAPE, NONWOVEN, SOUND ABATEMENTTHIS DOCUMENT MUST NOT BE REPRODUCED. IF USED IN RELATION TOTHE COMPANYS PRODU
10、CTS THE RECIPIENT IS RESPONSIBLE TO CONFIRMTHE DOCUMENT ISSUE DATE IS STILL VALID.FORM : I:LABRTORYFORMSTDMATSPEC.DOC8. REVISIONSFebruary, 2000 -Editorial and Formatting corrections.-References section added.Prepared by: Ron BoyackA.C.N. 006 893 232Holden LimitedEngineering DepartmentMATERIAL SPECIF
11、ICATIONNUMBERSHEETRELEASEREVISION:HN 22404 of 4October, 1996February, 2000NAME: ADHESIVE TAPE, NONWOVEN, SOUND ABATEMENTTHIS DOCUMENT MUST NOT BE REPRODUCED. IF USED IN RELATION TOTHE COMPANYS PRODUCTS THE RECIPIENT IS RESPONSIBLE TOCONFIRM THE DOCUMENT ISSUE DATE IS STILL VALID.FORM : I:LABRTORYFOR
12、MSTDMATSPEC.DOCTABLE 1 (Properties)Properties Values Test MethodsColour Dark Gray/Black Visual180oMean Peel StrengthAs ReceivedABSPP72 hr at 70 oCafter 24hr Humidity at 38oC, 95% RHABSPP650 N/m280 N/m825 N/m235 N/mASTM D 1000Shear StrengthCold, Tested at -18 oC after 24 hrs at -18oCABSPPHot, Tested
13、at 60 oC after 24 hrs at 60 oCABSPP0.15 MPa0.15 MPa0.20 MPa0.20 MPaASTM D 1000Tear Resistance 15 N ASTM D 1004Elongation Break Type 30 %, Type 300 % ASTM D 1000Abrasion Resistance, CS-10 Wheels, #cycles to fail.Dry, 500 gWet, 250 gType 500 cycles, Type 1500 cyclesType 250 cycles, Type 1000 cyclesHum
14、idity Resistance,48 hrs at 38 oC at 95 % RHNo Visible Loss of Adhesion BetweenTape & SubstrateHeat Resistance30 min at 120 oC168 hrs at 82 oCNo Visible Loss of Adhesion BetweenTape & SubstrateNo Visible Loss of Adhesion BetweenTape & SubstrateFogging (Bath Temperature = 110oC,Cooling Temperature = 38 oC)60 SAE J 1756Flammability, burn rate, max 100 mm/min SAE J369Odour, maxDryWet2 rating3 ratingSAE J 1351
