1、This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 by Navistar, Inc. AUGUST 2009 Page 1 of 3 NAVISTAR, INC. TMS (TRUCK MATERIAL SPECIFICATION) NUMBER:
2、TMS-6814 srr TITLE: Lubricant, Corrosion Control (Disk Brake) CURRENT REV No: 0908 DATE: August 2009 WRITTEN/EDITED BY: Materials Engineering APPROVED BY: Materials Engineering SUPERSEDES ISSUE : Rev. D-1 - August 2001 PRINTED COPIES OF THIS DOCUMENT MUST BE VERIFIED FOR CURRENT REVISION This specif
3、ication may involve hazardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health practices and to determine the applicability of regulatory limits prio
4、r to use. Change Notice: Replaced “International Truck and Engine Corporation” with “Navistar, Inc.” per corporate directive; added section 2.1 “Restricted Chemical Substances”; added section 10 “Technical Information”; editorial changes. Reference: File 30-8 Keywords: Lubricant; Disc Brake 1.0 APPL
5、ICATION This specification covers a National Lubricating Grease Institute (NLGI) Grade #1-1/2 non-filler grease suitable for lubrication of disk brake caliper and anchor plate slides and to provide long-term corrosion protection in these areas. 2.0 SCOPE This specification covers the property and pe
6、rformance requirements, quality, source approval and quality control, and approved sources. 2.1 Restricted Chemical Substances Effective January 1, 2007, all product supplied to the requirements of this specification must comply with the requirements of the CEMS B-50 specification. 3.0 REFERENCE DOC
7、UMENTS Unless otherwise specified the latest issue of all referenced standards shall apply. The following Specifications, Standards, and Regulations are referenced in this specification. Quality System Standard ISO 9001 or TS-16949 ASTM D 97 ASTM B 117 NAVISTAR Mfg. Standard MS-D-13 ASTM D 217 ASTM
8、D 942 CFR Title 29, Part 1910 ASTM D 445 ASTM D 1264 NAVISTAR CEMS B-50 ASTM D 566 ASTM D 1743 ASTM D 92 4.0 REQUIREMENTS 4.1 General This material shall consist of a mixture of mineral oil and an inorganic gel (calcium complex) base. 4.2 Color Color shall be brown. Copyright Navistar International
9、Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: TMS-6814 TITLE: Lubricant, Corrosion Control (Disk Brake) REVISION: 0908 This document is restricted and may not be sent outside Navistar, Inc. or reproduce
10、d without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 by Navistar, Inc. AUGUST 2009 Page 2 of 3 4.3 Cone Penetration (ASTM D 217) After 60 strokes, the penetration shall be 290-320. After 1x106 strokes, the maximum allowable change shall
11、 be 20. 4.4 Dropping Point (ASTM D 566) Shall be 260C (500F) minimum. 4.5 Water Washout (ASTM D 1264) Shall exhibit 5% max loss when tested at 80C (175F). 4.6 Rust Prevention Rating (ASTM D 1743) Distilled Water - 1 maximum 5% Sea Water - 1 maximum 4.7 Salt Spray (ASTM B 117) A 4” x 12” polished ste
12、el panel with a 4 mil film of grease shall not exhibit corrosion after 500 hours exposure. 4.8 Oxidation Stability (ASTM D 942) After 100 hours at 99C (210F) shall exhibit a maximum pressure drop of 34.5 kPa (5 psi). 4.9 Mineral Oil Properties 4.9.1 Viscosity (ASTM D 445) Shall be 10-16 cSt (59-82 S
13、US) at 100C (210F). 4.9.2 Pour Point (ASTM D 97) Shall be -15C (+5F) maximum. 4.9.3 Flash Point (ASTM D 92) shall be 215C (419F) minimum. 4.10 Vertical Sag Test 4.10.1 Material (a) One - 4“ x 12“ (approx.) cold rolled plain steel panel with a centered holed at one end for hanging (available from Adv
14、anced Coatings Technologies, Inc., 273 Industrial Drive, Hillsdale, MI 49242). (b) Triangular grease bead with a 1/2” height and 1/2” base across the width of the panel. (c) Forced convection oven capable of holding 125C 3C (260 5F) 4.10.2 Method Scribe a horizontal line on the upper third of the te
15、st panel and locate the grease sample such that the lower edge of the grease is just above the horizontal line when the panel is hung vertically. Hang the panel vertically in the oven for 70 hours at 125C (260 F). 4.10.3 Required The grease shall not sag more than 12 mm (0.5 inch). 5.0 QUALITY Mater
16、ial supplied to this specification shall be suitable for the intended application, clean and free from foreign materials and dirt, and adequately packaged and identified. 6.0 SOURCE APPROVAL AND QUALITY CONTROL 6.1 Supplier Requirements All suppliers to Navistar are required to be registered to ISO
17、9001 Quality System Requirements. Navistar will also accept TS-16949 registration as long as the supplier can also fulfill all AIAG PPAP (Production Part Approval Process) documentation and approval requirements. Suppliers must Copyright Navistar International Corporation Provided by IHS under licen
18、se with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: TMS-6814 TITLE: Lubricant, Corrosion Control (Disk Brake) REVISION: 0908 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Tec
19、hnical Standards. Suppliers are required to assume all patent liability. 2009 by Navistar, Inc. AUGUST 2009 Page 3 of 3 maintain their certification with an accredited registrar and must furnish copies of registration certificates to their Navistar Corporate Buyer upon request. 6.2 Approval Parts su
20、pplied against contracts or purchase orders citing this specification shall be equivalent in all respects to those samples, which were approved by the purchaser. No changes in formulation or processing practices are permitted without approval. In the event that changes occur in material properties,
21、processing practices, or labeling, the supplier shall notify Materials Engineering at TDTC and Navistar Purchasing and Supplier Development of the proposed change(s). Test data indicating conformance to all requirements of this specification, test samples, and new/amended/updated Material Safety Dat
22、a Sheet(s) (MSDS), in accordance with CFR Title 29, Section 1910, shall be submitted with the request for change. 6.3 Process Control The supplier shall either perform and report results of tests on specific lots of parts produced using ISO 9001 or TS-16949 guidelines, or provide statistical evidenc
23、e of the lot having been produced in a state of statistical control and with a process capable of providing all required properties. The part supplier and the plant metallurgist and/or the quality control manager of the using NAVISTAR plant may determine testing and reporting requirements on specifi
24、c products. 7.0 SHIPPING, PACKING AND IDENTIFICATION Shipping and identification shall be in accordance with Navistar Manufacturing Standard MS-D-13. When packaged for resale, containers, packaging and identification shall be in accordance with requirements set forth by the Parts Marketing Division
25、of the Parts Operation at Cantera in Warrenville, Illinois. 8.0 DESIGNATION ON DRAWINGS Lubricant per TMS-6814 9.0 APPROVED PRODUCTS Exxon Company, USA (Southwest Grease) “Corrosion Control Grease” Product Code SA8249496 - Navistar Bulk P/N 2643529R1 1-800-529-2576 10.0 TECHNICAL INFORMATION For fur
26、ther information related to the technical content of this specification, contact: Suppliers may purchase controlled copies of this specification by contacting: Materials Engineering and Technology Dept. Truck Development and Technology Center 2911 Meyer Road Fort Wayne, IN 46803 E-mail: MaterialsEng
27、ineeringN IHS Global Inc. 15 Inverness Way East Englewood CO 80112-5776 Phone: 1-800-854-7179 E-mail: AutomotiveIHS.com Website: http:/ Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
