ITU-R SF 675-4-2012 Calculation of the maximum power density (averaged over 4 kHz or 1 MHz) of angle-modulated and digital carriers《调角和数字载波的最大功率密度(平均超过4 kHz或1 MHz)计算》.pdf

上传人:jobexamine331 文档编号:793926 上传时间:2019-02-02 格式:PDF 页数:11 大小:1.35MB
下载 相关 举报
ITU-R SF 675-4-2012 Calculation of the maximum power density (averaged over 4 kHz or 1 MHz) of angle-modulated and digital carriers《调角和数字载波的最大功率密度(平均超过4 kHz或1 MHz)计算》.pdf_第1页
第1页 / 共11页
ITU-R SF 675-4-2012 Calculation of the maximum power density (averaged over 4 kHz or 1 MHz) of angle-modulated and digital carriers《调角和数字载波的最大功率密度(平均超过4 kHz或1 MHz)计算》.pdf_第2页
第2页 / 共11页
ITU-R SF 675-4-2012 Calculation of the maximum power density (averaged over 4 kHz or 1 MHz) of angle-modulated and digital carriers《调角和数字载波的最大功率密度(平均超过4 kHz或1 MHz)计算》.pdf_第3页
第3页 / 共11页
ITU-R SF 675-4-2012 Calculation of the maximum power density (averaged over 4 kHz or 1 MHz) of angle-modulated and digital carriers《调角和数字载波的最大功率密度(平均超过4 kHz或1 MHz)计算》.pdf_第4页
第4页 / 共11页
ITU-R SF 675-4-2012 Calculation of the maximum power density (averaged over 4 kHz or 1 MHz) of angle-modulated and digital carriers《调角和数字载波的最大功率密度(平均超过4 kHz或1 MHz)计算》.pdf_第5页
第5页 / 共11页
点击查看更多>>
资源描述

1、 Recommendation ITU-R SF.675-4(01/2012)Calculation of the maximum power density (averaged over 4 kHz or 1 MHz)of angle-modulated and digital carriersSF SeriesFrequency sharing and coordination betweenfixed-satellite and fixed service systemsii Rec. ITU-R SF.675-4 Foreword The role of the Radiocommun

2、ication Sector is to ensure the rational, equitable, efficient and economical use of the radio-frequency spectrum by all radiocommunication services, including satellite services, and carry out studies without limit of frequency range on the basis of which Recommendations are adopted. The regulatory

3、 and policy functions of the Radiocommunication Sector are performed by World and Regional Radiocommunication Conferences and Radiocommunication Assemblies supported by Study Groups. Policy on Intellectual Property Right (IPR) ITU-R policy on IPR is described in the Common Patent Policy for ITU-T/IT

4、U-R/ISO/IEC referenced in Annex 1 of Resolution ITU-R 1. Forms to be used for the submission of patent statements and licensing declarations by patent holders are available from http:/www.itu.int/ITU-R/go/patents/en where the Guidelines for Implementation of the Common Patent Policy for ITU-T/ITU-R/

5、ISO/IEC and the ITU-R patent information database can also be found. Series of ITU-R Recommendations (Also available online at http:/www.itu.int/publ/R-REC/en) Series Title BO Satellite delivery BR Recording for production, archival and play-out; film for television BS Broadcasting service (sound) B

6、T Broadcasting service (television) F Fixed service M Mobile, radiodetermination, amateur and related satellite services P Radiowave propagation RA Radio astronomy RS Remote sensing systems S Fixed-satellite service SA Space applications and meteorology SF Frequency sharing and coordination between

7、fixed-satellite and fixed service systems SM Spectrum management SNG Satellite news gathering TF Time signals and frequency standards emissions V Vocabulary and related subjects Note: This ITU-R Recommendation was approved in English under the procedure detailed in Resolution ITU-R 1. Electronic Pub

8、lication Geneva, 2012 ITU 2012 All rights reserved. No part of this publication may be reproduced, by any means whatsoever, without written permission of ITU. Rec. ITU-R SF.675-4 1 RECOMMENDATION ITU-R SF.675-4 Calculation of the maximum power density (averaged over 4 kHz or 1 MHz) of angle-modulate

9、d and digital carriers (1990-1992-1993-1994-2012) Rec. ITU-R SF.675-3 Scope This Recommendation provides methods for calculating the maximum power density of various types of carriers averaged over 4 kHz or 1 MHz. The ITU Radiocommunication Assembly, considering a) that administrations are requested

10、 to prepare the information listed in Appendices 3 and 4 to the Radio Regulations (RR) for coordination and notification purposes; b) that one item of the information listed in RR Appendices 3 and 4 is the maximum power density per Hz at the input of the antenna; c) that RR Appendix 4 prescribes tha

11、t the maximum power density per Hz of a carrier is averaged over the worst 4 kHz band for frequencies below 15 GHz and is averaged over the worst 1 MHz band for frequencies above 15 GHz; d) that generalized methods are necessary for the calculation of the maximum power density of an angle-modulated

12、carrier; e) that tracking, telemetry and telecommand (TT 2 that the methods described in Annex 2 should be used for calculation of the maximum power density, averaged over 1 MHz, of digital or TT 3 that for the determination of the maximum spectral power density, with agreement of the other administ

13、rations concerned, the objectives of Resolution 703 (Rev.WRC-07) should be followed. 2 Rec. ITU-R SF.675-4 Annex 1 Calculation of the maximum power density (averaged over 4 kHz) of an angle-modulated carrier Given below is the method of calculating the power level in the worst 4 kHz (W/4 kHz). The p

14、ower density per Hz required by the RR is obtained by dividing this value by 4 000. 1 FM carrier 1.1 FM carrier modulated by a multi-channel telephony signal The maximum power spectral density at full baseband loading is determined either by the residual carrier or by the peaks of the continuous spe

15、ctrum, depending upon the nature of the modulation. The power of the residual carrier is given by the expression: Pt e0mmmmmmW (1) where: ()+=32420230CCCm(2) In equation (2), m is the multi-channel r.m.s. modulation index and the constants C0, C2and C4describe the prevailing pre-emphasis characteris

16、tic in the general expression for the pre-emphasis: p(/h) = C0+ C2(/h)2+ C4(/h)4 (3) where is the specific baseband frequency under consideration, to be given in the same units as h. In the range /h 1, the pre-emphasis characteristic is well approximated by: p(/h) = 0.4 + 1.35(/h)2+ 0.75(/h)4(4) Thu

17、s, for a system with pre-emphasis: 0223(0.4 + 1.6 + 0.25 + 0.25 )m(5) Where m = /h. NOTE 1 Administrations should make available details of the spectrum shape and the value of the coefficients used in equations (2) and (3), for detailed coordination purposes. The maximum power of the spectral densit

18、y in the continuous part of the spectrum can be obtained approximately from Figs 1 and 2. Rec. ITU-R SF.675-4 3 FIGURE 1 Maximum spectral density of signal (distributed component) frequency modulated by Gaussian noise SF.0675-01C1202 7001 800D9001 200GJAB6003009601 260HEF11731591317125102510 1Normal

19、izedspectraldensity(powerperunitbandwidth/totalcarrierpower),(dB)VmaxNormalized frequency deviation, m = f / fhCurves A: = 0.1B: = 0.2C: = 0.4D: = 1.0E: = 2.0F: = 4.0G: = H: small-deviation approximationJ: large-deviation approximation0000000Values for standard radio-relay systems(as labelled) are f

20、or the following baseband limits:120 channels 60-552 kHz960 channels 60-4 028 kHz1 260 channels 60-5 636 kHz4 Rec. ITU-R SF.675-4 FIGURE 2 Equal contour of Vmax(maximum spectral density) of the FDM-FM signal SF.0675-02Multichannel modulation (= / ), hm20141618810126420 8 6 4 2 4 6 80.1103.0102.5102.

21、0101.5101.0100.50.5 1.0 1.5 2.0 2.5Ratioofminimumto maximumbasebandfrequencies, In the equations and the figures, the symbols have the following meanings: Pt: total power of carrier (W) : multi-channel r.m.s. deviation (Hz) 1260for1060240for10240for 10)/20 log 2+(2.6)/20 log 4+1()/20 log 10+15(cNdcN

22、dcNdNfNfNffccc24012for10240for10or )/20 log 4+1()/20 log 10+15(cNdcNdNfNfccd: r.m.s. test tone deviation (Hz) Nc: number of channels h: top frequency of the baseband (Hz) 1: bottom frequency of the baseband (Hz) m : multi-channel modulation index (= /h) = 1/ hVmax= Wmaxh / PtWmax: maximum spectral p

23、ower per unit bandwidth (W/Hz). Rec. ITU-R SF.675-4 5 For carriers for which 1 N 12, the maximum power density per 4 kHz is approximated by the expression: Ptcos2mb1.5mmmmmmW/4 kHzmmmmmmfor mb 1 (6) where: Pt: total power of the carrier (W) mb: peak modulation index (rad) due to a 0 dBm test tone in

24、 the highest frequency baseband channel. 1.2 FM carrier modulated by a multi-channel telephony signal and an energy dispersal signal of a triangular waveform with fixed amplitude Triangular wave dispersal systems are normally designed to ensure that the maximum power spectral density per 4 kHz centr

25、ed on the carrier frequency is maintained within 3 dB of the fully loaded value. The power spectral density centred on the carrier frequency is given by: 4000FPtkHzW/4 (7) where: Pt: total power of the carrier (W) F : peak-to-peak frequency deviation due to the energy dispersal signal (Hz). NOTE 1 E

26、quation (7) assumes the use of a perfectly linear triangular dispersal waveform. 1.3 FM carrier modulated by a television video signal For the case where an energy dispersal signal of a triangular waveform is superimposed on the video signal, the maximum power density per 4 kHz in the worst case is

27、given by: 4000FPtkHzW/4(8) where: Pt: total power of the carrier (W) F : peak-to-peak frequency deviation due to the energy dispersal signal (Hz). NOTE 1 Equation (8) assumes the use of a perfectly linear triangular dispersal waveform. Negligible error results from this assumption for current FM-TV

28、transmissions. For the case where there is no modulation by video and energy dispersal signals, the maximum power density per 4 kHz in the worst-case is given by: PtmmmmmmW/4 kHz 2 Phase modulated (PM) carrier modulated by a multi-channel telephony signal When a PM carrier is modulated by a multi-ch

29、annel telephony signal, the maximum power density is found at the centre frequency of the carrier. This is true if the top baseband frequency is much larger than the bottom baseband frequency. An expression for the maximum power density assuming this condition is given as follows: 6 Rec. ITU-R SF.67

30、5-4 for a 2: Pt(a) h32 4 000mmmmmmW/4 kHz (9) for a 2, the maximum power density per 4 kHz is the sum of following two terms: continuous spectrum: Pt S(0) 4 000mmmmmmW/4 kHz (10) S(0) can be found from Fig. 3 which gives values for the ratio of the total carrier power-to-power density in a bandwidth

31、 of h(Hz). residual carrier: Ptexp (a)2mmmmmmW (11) where: Pt: total power of the carrier (W) a: multi-channel phase deviation (rad) : r.m.s. test tone phase deviation (rad) a: loading factor of the multi-channel telephony signal. a= 240for10240for10N)/20 log 4+1()/20 log 10+15(NNNN : channel number

32、 h: top baseband frequency (Hz). FIGURE 3 Power density at the centre frequency of continuous power spectrum of PM carrier in a bandwidth of fhSF.0675-030246810121416182001234567Multi-channel phase derivation, a(rad)Ratio oftotalcarrierpower-to-powerdensityinabandwidth of,(0)(dB)hShRec. ITU-R SF.675

33、-4 7 3 Digital carrier with necessary bandwidth greater than 4 kHz The maximum power density per Hz of a digital carrier is given by: Po = Pt/B (12) where: Pt: total power of the carrier (W) B : necessary bandwidth of the digital emission (Hz). The maximum power density per 4 kHz in the worst case i

34、s given by multiplying the result of equation (12) by 4 103 as: P4 kHz= Po* 4 103(W/4 kHz) (13) 4 Digital carrier with necessary bandwidth less than 4 kHz For those cases with multiple identical carriers with a bandwidth less than 4 kHz where it is known that any 4 kHz will not be completely filled

35、with such carriers, the following equation should be applied: P4 kHz= (Pt* N) (W/4 kHz) (14) where: Pt: total power of a single carrier (W) N: maximum number of carriers, or portions of carriers, with a bandwidth less than 4 kHz to occupy any given 4 kHz band. Equation (14) can be generalized for th

36、e case where it is known that there will be multiple different types of carriers with bandwidths less than 4 kHz occupying any given 4 kHz band by summing the power of the various individual carrier types to occupy the 4 kHz band and assuming this total power is the power per 4 kHz. 5 TT&C carrier W

37、hen narrow-band TT&C carriers are involved, in accordance with RR No. 1.23, in frequency bands below 15 GHz, care must be taken in assessing the maximum power per 4 kHz for such carriers. This is due to the fact that such carriers can have multiple distinct and significant spectral components. As su

38、ch, it is important to consider the actual spectral shape of such TT&C carriers when selecting the worst 4 kHz bandwidth in order to assess the maximum power density. 8 Rec. ITU-R SF.675-4 Annex 2 Calculation of the maximum power density (averaged over 1 MHz) of a digital or TT&C carrier Given below

39、 is the method of calculating the power level in the worst 1 MHz (W/MHz). 1 Digital carrier with necessary bandwidth greater than 1 MHz The maximum power density per Hz of a digital carrier is given by: Po= Pt/B (W/Hz) (15) where: Pt: total power of the carrier (W) B: necessary bandwidth of the digi

40、tal emission (Hz). The maximum power density per MHz in the worst case is given by multiplying the result of equation (15) by 1 106 as: P1 MHz= Po* 1 106(W/MHz) (16) 2 Digital carrier with necessary bandwidth less than 1 MHz Note that for digital carriers with a necessary bandwidth less than 1 MHz,

41、a determination must be made as to the maximum number of carriers, and portions of carriers, that will be operating in any 1 MHz band. Where this maximum number of carriers is not known, an assumption should be made that the 1 MHz reference bandwidth will be filled with multiple identical carriers.

42、Under this assumption equations (15) and (16) provide the estimate of the maximum power density per MHz in the worst case. For those cases with carriers with a necessary bandwidth less than 1 MHz where it is known that any 1 MHz will not be completely filled with multiple identical carriers, the fol

43、lowing equation for calculating the maximum power density per 1 MHz should be applied: P1 MHz= (Pt* N) (W/MHz) (17) where: Pt: total power of a single carrier (W) N: maximum number of carriers, including portions of carriers, with a necessary bandwidth less than 1 MHz to occupy any given 1 MHz band.

44、 Equation (17) can be generalized for the case where it is known that there will be multiple different types of carriers with necessary bandwidths less than 1 MHz occupying any given 1 MHz band by summing the power of the various individual carrier types to occupy the 1 MHz band and assuming this to

45、tal power is the power per 1 MHz. 3 TT&C carrier When, in accordance with RR No. 1.23, narrow-band TT&C carriers are involved, the calculation of maximum power density per MHz can lead to an overestimation of the potential interference power. This is due to the fact that simply scaling the power of

46、a single TT&C carrier up to 1 MHz by applying a ratio of the bandwidths would result in a power level greater than the TT&C carrier itself when a single TT&C carrier with a necessary bandwidth less than 1 MHz is used in a given frequency assignment. In such cases, the interference potential caused b

47、y a TT&C carrier would be Rec. ITU-R SF.675-4 9 more accurately assessed if recognition were given to the fact that, in most cases, only a single TT&C carrier will be transmitted in any given 1 MHz band. As such, the maximum power density per 1 MHz for a TT&C carrier having a necessary bandwidth les

48、s than 1 MHz is given by: Pt(W/MHz) (18) where: Pt: total power of the TT&C carrier (W). For the case of a TT&C carrier having a necessary bandwidth greater than 1 MHz, but not more than 1.5 MHz, the maximum power density per 1 MHz is given by: Pt (1 106/B) (W/MHz) (19) where: Pt: total power of the TT&C carrier (W) B: necessary bandwidth of the TT&C emission which is greater than 1 MHz (Hz). _

展开阅读全文
相关资源
猜你喜欢
  • STAS SR EN 196-7-1995 Methods of testing cement Methods of taking and preparing samples of cement《水泥测试方法 采取和准备水泥样品的方法》.pdf STAS SR EN 196-7-1995 Methods of testing cement Methods of taking and preparing samples of cement《水泥测试方法 采取和准备水泥样品的方法》.pdf
  • STAS SR EN 2-1995 Classification of fires《火的分类 》.pdf STAS SR EN 2-1995 Classification of fires《火的分类 》.pdf
  • STAS SR EN 2000-1995 Aerospace series Quality assurance EN aerospace products Approval of the quality system of manufacturers《航空航天系列 质量保证 EN航天产品 制造商的质量系统的通过》.pdf STAS SR EN 2000-1995 Aerospace series Quality assurance EN aerospace products Approval of the quality system of manufacturers《航空航天系列 质量保证 EN航天产品 制造商的质量系统的通过》.pdf
  • STAS SR EN 202-1994 Ceramic tiles — Determination of frost resistance《瓷砖 抗冻性的测定 》.pdf STAS SR EN 202-1994 Ceramic tiles — Determination of frost resistance《瓷砖 抗冻性的测定 》.pdf
  • STAS SR EN 2022-1994 Aerospace series Bearings spherical plain in corrosion resisting steel with self-lubrificating liner Light series Dimensions and loads《航空航天系列.轴承.带自润滑内衬的耐蚀钢普通球面.pdf STAS SR EN 2022-1994 Aerospace series Bearings spherical plain in corrosion resisting steel with self-lubrificating liner Light series Dimensions and loads《航空航天系列.轴承.带自润滑内衬的耐蚀钢普通球面.pdf
  • STAS SR EN 2070-1+A1-1996 Aerospace series Aluminium and aluminium alloy wrought products Technical specification Part 1 General requirements《航空航天系列铝和铝合金锻造产品 技术规范 第1部分:一般要求》.pdf STAS SR EN 2070-1+A1-1996 Aerospace series Aluminium and aluminium alloy wrought products Technical specification Part 1 General requirements《航空航天系列铝和铝合金锻造产品 技术规范 第1部分:一般要求》.pdf
  • STAS SR EN 2076-1+A1-1995 Aerospace series Aluminium and magnesium ailoy ingots and castings Technical specification Part 1 General requirements《航空航天系列 铝和镁合金锭和铸件 技术规范 第1部分:一般要求》.pdf STAS SR EN 2076-1+A1-1995 Aerospace series Aluminium and magnesium ailoy ingots and castings Technical specification Part 1 General requirements《航空航天系列 铝和镁合金锭和铸件 技术规范 第1部分:一般要求》.pdf
  • STAS SR EN 2076-2-1995 Aerospace series Aluminium and magnesium alloy ingots and castings Technical specification Part 2 Ingots for remelting《航空航天系列 铝和镁合金锭和铸件 技术规范 第2部分: 重熔锭》.pdf STAS SR EN 2076-2-1995 Aerospace series Aluminium and magnesium alloy ingots and castings Technical specification Part 2 Ingots for remelting《航空航天系列 铝和镁合金锭和铸件 技术规范 第2部分: 重熔锭》.pdf
  • STAS SR EN 2078-1995 Aerospace series Metallic materials Manufacturing schedule Inspection schedule inspection and test report Description and rules for use《航空航天系列.金属材料.生产进度.检查时间表..pdf STAS SR EN 2078-1995 Aerospace series Metallic materials Manufacturing schedule Inspection schedule inspection and test report Description and rules for use《航空航天系列.金属材料.生产进度.检查时间表..pdf
  • 相关搜索

    当前位置:首页 > 标准规范 > 国际标准 > 其他

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1