JUS C D1 005 1-1986 Copper and copper alloys Copper alloys for castings Chemical composition designation quality re-guirements Amendments《铜和铜合金 铸造用铜合金 化学成分、命名和质量要求 修订版》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

AGMA 06FTM04-2006 Precision Planetary Servo Gearheads《精密行星伺服齿轮头》.pdf

AGMA 06FTM05-2006 Development of a Gear Rating Standard - A Case Study of AGMA 6014--A06《齿轮分级标准的发展.AGMA 6014--A06的案例研究》.pdf

AGMA 06FTM06-2006 An Analytical Approach to the Prediction of Micropitting on Case Carburised Gears《层渗碳齿轮微点蚀的预测分析方法》.pdf

AGMA 06FTM07-2006 Improvement of Standardized Test Methods for Evaluating the Lubricant Influence on Micropitting and Pitting Resistance of Case Carburized Gears《评估润滑剂对层渗碳齿轮上微点蚀和抗点.pdf

AGMA 06FTM08-2006 An Evaluation of FZG Micropitting Test Procedures and Results for the Crowned AGMA Test Gears《鼓形AGMA测试齿轮用FZG微点蚀测试程序和结果的评估》.pdf

AGMA 06FTM09-2006 Opportunities to Replace Wrought Gears with High Performance PM Gears in Automotive Applications《在汽车应用中用高性能PM齿轮替换精加工齿轮的时机》.pdf

AGMA 06FTM10-2006 Fabrication Assembly and Test of a High Ratio Ultra Safe High Contact Ratio Double Helical Planetary Transmission for Helicopter Applications《直升机设施用双螺旋混合行星齿轮传动高接触.pdf

AGMA 06FTM11-2006 On Tooth Failure Analysis in Small--Teeth--Number Gearing An Analytical Approach《小齿数齿轮上轮齿故障分析 分析方法》.pdf

AGMA 06FTM12-2006 A Crane Gear Failure Analysis -- Case Study Observations Lessons Learned Recommendations《起重机齿轮疲劳分析.案例研究、观察、课程学习、介绍》.pdf