MSZ 6575 20-1979 《皮带扣检测层厚度测量与测试》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

KS P ISO 8362-2-2009 Injection containers and accessories－Part 2：Closures for injection vials《注射容器及附件 第2部分 注射瓶的封口》.pdf

KS P ISO 8362-3-2009 Injection containers and accessories－Part 3：Aluminium caps for injection vials《注射容器及附件 第3部分 注射小瓶用的铝盖》.pdf

KS P ISO 8362-5-2009 Injection containers and accessories－Part 5：Freeze drying closures for injection vials《注射容器和附件 第5部分 注射瓶用冷冻干燥塞》.pdf

KS P ISO 8362-7-2009 Injection containers and accessories－Part 7：Injection caps made of aluminium-plastics combinations without overlapping plastics part《注射容器及附件 第7部分 无重叠塑料部件的由铝和塑料.pdf

KS P ISO 8536-3-2009 Infusion equipment for medical use－Part 3：Aluminium caps for infusion bottles《医用输液器具 第3部分 输液瓶铝帽》.pdf

KS P ISO 8536-5-2009 Infusion equipment for medical use－Part 5：Burette infusion sets for single use gravity feed《医用输液器具 第5部分 一次性使用重力输液的滴定管式输液器》.pdf

KS P ISO 8536-6-2009 Infusion equipment for medical use－Part 6：Freeze drying closures for infusion bottles《医用输液器具 第6部分 输液瓶的冷冻干燥瓶塞》.pdf

KS P ISO 8536-7-2009 Infusion equipment for medical use－Part 7：Caps made of aluminium-plastics combinations for infusion bottles《医用输液器具 第7部分 输液瓶用铝和塑料复合物制帽盖》.pdf

KS P ISO 8548-1-2008 Prosthetics and orthotics－Limb deficiencies－Part 1：Method of describing limb deficiencies present at birth《修复术和矫形学 肢缺陷 第1部分 先天肢缺陷描述方法》.pdf