MSZ 6579 1-1984 《无机非金属涂层检查之磷酸锌表层》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

FORD ESB-M4D297-A1-2009 ABS 10% GLASS FIBER REINFORCED MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《丙烯腈-丁二烯-苯乙烯共聚物（ABS）10%玻璃纤维增强的成型料 与标准FORD WSS-M99P1111-A一起使用 》.pdf

FORD ESB-M4D297-A2-2009 ABS 20% GLASS FIBER REINFORCED MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《20%玻璃纤维增强的丙烯腈-丁二烯-苯乙烯共聚物(ABS)成型料 与标准FORD WSS-M99P1111-A一起使用 列于标准FOR.pdf

FORD ESB-M4D297-A3-2005 ABS 30% GLASS FIBER REINFORCED MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A (Shown on ESB-M4D297-A1)《30%玻璃纤维增强的丙烯腈-丁二烯-苯乙烯共聚物(ABS)成型料 与标准FORD WSS.pdf

FORD ESB-M4D299-A-2011 POLYPROPYLENE GLASS FIBER REINFORCED INJECTION MOLDING COMPOUND - NATURAL TO BE USED WITH FORD WSS-M99P1111-A 《玻璃纤维加强喷射成型自然聚丙烯 与福特WSS-M99P1111-A 一起使用》.pdf

FORD ESB-M4D300-A-2008 ABS MOLDING COMPOUND HIGH IMPACT - HIGH TEMPERATURE TO BE USED WITH FORD WSS-M99P1111-A 《丙烯腈-丁二烯-苯乙烯模塑料 耐冲击 耐高温(和FORD WSS-M99P1111-A一起使用)(使用 FORD WSB-M4D69.pdf

FORD ESB-M4D308-A-1983 POLYPROPYLENE HIGH IMPACT GRADE - INJECTION MOLDING《高抗冲级聚丙烯（PP）注塑塑料》.pdf

FORD ESB-M4D308-B-2006 POLYPROPYLENE FOAMED EXTRUSION TO BE USED WITH FORD WSS-M99P1111-A 《聚丙烯（PP）泡沫挤塑塑料 与标准FORD WSS-M99P1111-A一起使用 使用ESB-M4D308-A》.pdf

FORD ESB-M4D311-A-2008 POLYETHYLENE HIGH DENSITY - EXTRUSION GRADE - EXTERIOR TO BE USED WITH FORD WSS-M99P1111-A 《汽车外部用挤塑级高密度聚乙烯 与标准FORD WSS-M99P1111-A一起使用 》.pdf

FORD ESB-M4D317-A-2010 POLYVINYL CHLORIDE INJECTION MOLDING COMPOUND - ELECTRICAL GRADE TO BE USED WITH FORD WSS-M99P1111-A 《电气级喷射成型聚氯乙烯 与福特WSS-M99P1111-A 一起使用》.pdf