1、 L-F-315C 67 7777774 0012423 5 -7-r- L-F-315C November 15. 19n SUPERSEDING Fed. Spec. L-F-315b April 24, 1965 FEDERAL SPECIFICATION FILM, DIAZOTYPE, SENSITIZED (DIRECT IMAGE MICRoFoFfMS) This specification was approved $. the Commissioner, Federal Supply Service, General Services Administration, for
2、 the use of all Federal agencies. 1. SCOPE AND CLASSIFICATION 1.1 Scope. This specification covers the requirements for positive working, direct image ammonia developed diazotype films intended for use in microreproduction eystems. -Where applicable, films include those in rolls, sheets and mounted
3、in FAM copy cards. 1.2 Classification. Diazotype film covered by this specification shall be classified using the designators specified in table I, and meting the requirements put forth in table II. products nominal value of the appropriate characteristic will fall within one of the designator group
4、s. The film product supplied by the manufacturer shall not vary more than a fixed percentage of the manufacturers nominal stated value, as shown on table I. conceivable combination of sensitized product, many of these products are not feasible in the diazo process at this the. The film While this de
5、signator system includes every 2. APPLICABLE DOCUMENTS 2.1 The following documents, of the issues in effect on date of invitation for bids, or request for proposal, form a part of this specification to the extent specified herein. Federal Specifications: PPP-E601 - Boxes, Wood, Cleated-Plywood. PPP-
6、E621 PPP-E636 - Box, Fiberboard. pPP-Eb640 PPP-T-60 - Boxes, Wood, Nailed and Lock-Corner. - Box, Fiberboard, Corrugated, Triple-Wall. - Tape, Pressure Sensitive, Adhesive, Waterproof for packaging. Federal Standards: Fed. Std. No. 123 - Harking for Domestic Shipmsnt (Civil Agencies): (Activities ou
7、tside the Federal Government may obtain copies of Federal Specifications, Standards, and Handbooks as outlined under General Information in the Index of Federal Specifications and Standards and at the prices indicated in the Index. issued, is for sale on a subscription basis by the Superintendent of
8、 Documents, U, S. Governuent Printing Office, Washington, D. C. 20402. The Index, which includes dative rnmthly supplements as (Single copies of this specification and other Federal Specifications required by activities outside the Federal Government for bidding purposes are available without charge
9、 from Business Service Centers at the General Services Administration Regional Offices in Boston, New York, Washington, X, Atlanta, Chicago, Kansas City, M, Fort Worth, Denver, San Francisco, Los Angeles, ad Seattle, UA. and the Index of Federal Specifications ami Standards from established distribu
10、tion paints in their agencies. ) (Federal Government activities may obtain copies of Federal Specifications, Stadards, and Handbooks .-. FSS 6750 I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-c Military Specifications: MIL-L-10547 - Uners, Case,
11、Waterproof. .- . (Copies- O? Military Spesifications aidstandards required by sappliers in cmectiou with spclfic proornament fugcViom sbodd be obtained Prom the piwcuring acitivity or 9s irecbed by the coutrrscting o ef icer . ) 2.2 Other pliifiicatisns. Tue following docirimats fern R purt o? this
12、apocification to the extent specified herein. for Oils or request for progosa1 shall .qpp2;7: Unleas a spocific issue is idSntifid, the isaae in effect on date of invitatiou -.- Ammican Natioluli Sta-dars 1ns;itu:e (ANSI) Stanads: PHl,13 - Coras for Photogap.iiic Film ?tolls (Plsatic, Waod) Dr Metal
13、), Miaeneiona for, PH1.16 - Grapiic Arts Sheet Film (Inch and Centimeter Sizes), Dimensions for, PHl.20 - 70mm Unperforated and Perforated Film for Canrn Other tha2 Iilotio?i-?ickure Canaras, Dimensions for. PHl.25 - Safety Photographic Film, Specifications for. PH1.23 - Curl of PhoLogaphic Film, Me
14、thod3 fo? Determining the. Pn1.32 - Determining the Dimanioiial Chaage Characteristics o.? Tho5ographic Films and Papera, Meth Microfiche Standards, ThirU Edition, April 1968. (Copies of the Micrfiche Stanmd are availsble from the Cleariff Xoiise for Federal ScienLAfic and Tecanicol Information, Sil
15、s kildlng, 5245 Pork Royal ?bad, SpringfielSI Virginis 22171. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-National Motor Freight Traffic Association, Incorporated, Agent: National Motor Freight Classification. (Application for copies should be
16、addressed to the American Rucking Association, Inc., Tariff Order Section, 1616 P Street, N.W., Washington, D. C. 20036.) Uniform Classification Committee. Agent: Uniform Freight ClassificaP;ion. (Amlication fez- copies should be addresse3 to the niform ClassiIicatLon Committee, Room 202 Union 3. RE
17、Qmms 3.1 Materials. The diazotype film procured in accordance with tus specification shall meet all Station, 516 W. Jackson Blvd., Chicago, Illinois 60606.) the requirements specified herein. the suscification shall be raplaced by the manufacturer at no additional cast to the Government. Any materia
18、l which exhibits casting or physical defects not meeting 3.2 When examined for the p.hysical defects listed in 4.4.2.1.1, 8s spacifid in 4.3.1, the film shall be free from defects of a physical nature that will impair the md use of the praiuct for duplicstinp microfilms. 3.3 3.4 Classification desig
19、nators, (table I), 3.4.1 Film base. Ths film base shall be an opticslly, homogenous, transpwerit medium. The film Emiration date, Unless otherwise spsoified (see 6.2), the expiration date of the diazotype microfilm shall be not less than 99 days from the dste uf shipment. base shall aoqly with only
20、the burning requiremnts of ANSI PHl.25, a.* ss define8 therain for Safety Photographic Film.“ 34.2 Celluio3e ester base. 3.4.3 Cellulose ester base shall conform to ANSI PK1.25. The film shall meet the dimensional stability requirements specified Dimensional stabilitv, in table II, when tested in ac
21、cordance with 4.3.3. 3.4.4 Total product thickness. The nominsl total product thickness of Formt 1, 2 and 3 film (table 11) shall conform to the desimator in table I when tested immediately after slitting in .- - accordai; with-4.3.4. percent. 3.4.5 satisfactorily in equipment utilizing high tempera
22、ture, 120 to 220 F., and ambient pressure as development conditions. Thickness vGiations from the manufacturers nominal- shall be within i 10 Development tvpe high temperature - ambient pressure. Tqs diazo film is designed to Aevelop 3.4.6 Development tme mbient temperature - hivh prassure. This dia
23、zatypu film is designed to develop satisfactorily in equipment utilizing ambient temperature and high pressure, above 30 lbs. per square in-h as development conditions. designed for viwhng, blowsScas, o? reprinting; and a sepia lintermediate“ u3ed solely as a duplicate master film. 3.4.7 Film usage.
24、 The film usage shall conform to the designator in table I; a iiprinttt film 3.4.8 ARMM speed ratino. The nominal AFW spead designator of the film shall conform to the values in table I when tested in acoordsnae with 4.3.5. noninal shall be -thin _+ 20 percent. Sped variations from the msnufacturers
25、 3.4.9 Bar pamma . The nominal bar gamma designator of film specified herein shall conform to Variations fro% the manufacturers noainsl the values in table I when tested as spscifie8 in 4.3.6. shall bs within210 percent. 3.4.10 Bar !mama ratio. The bar gms ratio designator of the film specified here
26、in shall meet the values shoxn in table I when tested in accordsnce with 4.3.7. manufacturers nominal shall be within _t 10 percent. Bar gamma ratio variations from the 3.4.11 Maximm density. The mximum density designator of films specified herein shall be in accordance with the values in table I wh
27、en tested as specified in 4.3.8. from the manufacturers nominal shall be within? 10 percent Maximum density variations 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-4 ! Provided by IHSNot for ResaleNo reproduction or networking permitted without
28、license from IHS-,-,-L-F-315C 67 777777L1 0032927 2 m sPF-315C 3.5 Product characteristics (,t+ble 11). 3.5.1 Format. Tnree formats as supplied by the manufacturer are specified in table II. 3.5.2 Width format 1 and 2. Format 1 and 2 films shall conform to the width in table II when testad imediatel
29、y after slitting in accordance with 4.3.9. 3.5.3 Size format 3 . Format 3 film shall conform to the size specifications Of page 1 of PB 167/630, Microfiche Standards, Third Edition, April 1968, or its latest revision. 3.5.4 Splices. mmat 1 and 2 fib supplied in XOCI and 2000 foot lengtins may contai
30、n one splice, provided that not more than 10 percent of such spliced rolls are included in any one shipment. 3.5.5 Spools and cores. Unless otherwise specified by the ordering activity (see 6.2), spools for 16mm by 100 feet shall be in accordance with ANSI PHl.33. accordance with ANSI PH1.34. Spools
31、 for 7Omm shall be in accordance with iss-26565. Cores shall be in accordance with ANSI PH.13. Commercial spools or cores not covered by the above specified ANSI and I45 Standards may be supplied when the contractor has certified that the performance of the comercial spools or cores are equal to or
32、better thai th? s-.t;r:.rl s-cls or cores (see 6.2). Spools for 16 mm by 200 feet shall be in Spools for 35mm by 100 feet shall be in accordance with ANSI PH1.35. 3.5.6 Roll lemths. Formt 1 ancl 2 film shall conform to the roll length in table II. 3.5.7 Nuher of s3egta Deraackaze. Formt 3 fiLu ahall
33、 c.xfom to the amber uf sheets T!r package in table II. TABLE II. Characteristics - designators A. Format (3.5.1) 1. Rolls - unperforated 2. Rolls - perforated 3. Sheets B. Width* (3.5.2 and 3.5.3) 16mm - 0.626 2 0.002 inches 35m - 1.377 2 0.002 inches 7Omm - 2.754 2 0.005 inches Tab Card - 3.245 2
34、0.005 inches 105 - 4.129 2 0.005 Inches 3-1/4 inch - 3.245 2 0.005 inches Microfiche - 105 x 146.75m, +O -0.75nu.u 3.250 x 7.375 inches (+O -0.030 inches) Unless otherwise specified weasured at 72O. + Other sizes cut to ANSI Standard PH1.16. PF. and 50 percent RH 2 2 percent . loo, 200, 300, 400, 50
35、0, 1000, 2000 ft. *A combined integral film leader and trailer not less than 4ft. in length shall be included on each roll. D. Number of heets wr mckape (3.5.7) 100, 500 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EpF-315C TXBLE II. (CON.) E, w
36、nirnum Densitz (3.5.9) 0.12,minlrnum (see 4.3.10). - F. Actinic Wansmission (3.5.10) 30 percent minimum (see 4.3.11). G. H. Resolving Power (3.5.11) Accelerated Aging ChaPacterlstics (se3,5.i3 and .ocessiog of sanples before neasurement i 4. SP34FLIPS A?m IssoEmIoN 4.1 Responsibility for inspection.
37、 Unless otherwise specified in the contract or purchase order, the supplier is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified, the supplier may utilize his own facilities or any commercial laboratop acceptable to the Government. The
38、Government reserves the right to perform any of the Inspections set forth ip the specification where such inspections are deemed necessary to assure that supplies and services conform to prescribed requirements. 4.2 Sampling f.or inspection and acceptance. Unless otherwise specified (see 6.2), sampl
39、ing for inspection and acceptance shall be performed in accordance with MIL-STD-105. sampling an inspection lot for examination closures not accomplished by specified or required methods or materials. Number of rolls or packages per carton less than indicated or specifid. Marking not in accordance w
40、ith contract specifications. Labels when used not properly attached. Markings illegible, incorrect, incomplete, omitted, or not in accordance with contract requirements. Gross weight exceeds contract requirements. 4.2.2.1.5 -on levels and Aas for examinations. The inspection levels, for determining
41、the sample size and the AQs expressed in defects per 100 units, shall be as follows: Examination 4.2.2.1.1 4.2.2.1.2 Inspection level I s-3 1.0 2.5 4.2.2.1.3 s-2 2.5 4.2.2.1.4 S-4 4.0 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-L-F-3L5C 67 7777
42、774 0032432 b 1 . kF-315C 4.2.3 Testing of the end item, Testing of the end item shall be conducted in accordance with The table III for the characteristics as indicated therein on each lot submitted for acceptance, sample unit, as referenced herein is defined as the amount of material required to p
43、erform ail tests at one time. Three sample units, each drawn from a different shipping container, shall be tested with no evidence of failure to meet sample unit or average requirements, as applicable. The sample unit for di testing shall consist of one roll or one packge of fib. TABLE II. Instructi
44、ons for testing (Sample unit) Characteristic ReolVLng Parer Sensitometric Characteristics Dimensional Stability Humidity Thermal coefficient Coefficient Humidity Change Thermal Change Width and Size oll length Number of Sheets Accelerated Agi% Curl 10 Specification Reference Requirement 3.5.n 3.4.8
45、3.4.9 3.4.10 3.43. 3.5.9 3.5.10 3.5.13 3.4.3 3.5.2 3.5.3 3.5.6 3.5.7 3.5 S2.1 3.5 S2.2 3.5.12.3 3.5.12.4 3.5 .U. 5 3.5 2.6 3.5.U.l 3.5.u.2 Test Method 4.3.12 4.3.5 4.3.6 4.3.7 4.3.8 4.3.10 4.3.n 4.3.34 4.3.3 4.3.3.1 4.4.3.2 4.3.3.3 4.3.3.4 4.3.9 -I- - 4.3.13.1 4.3.13.2 4.3.13.3 4.3.13.4 4.3.13.5 4.3
46、.13.6 - Requirements applicable tc Individial unit X X X X X X X X X X X X X X X lo. Determinations Per Sample Unit Avg. of 5 Avg. of 2 Avg. of 2 kvg. of 2 Avg. of 2 Avg. of 2 Avg. of 2 Avg. of 2 Avg. of 5 Avg. of 5 Avg. of 5 Avg. of 5 Avg. of 5 Avg. of 2 Avg. of 2 Avg. of 2 Avg. of 2 Avg. of 2 Avg.
47、 of 2 Avg. of 2 Avg. of 2 Avg. of 5 Avg. of 5 Results Reported as - pass Fail X - - - I X X X X X X X X X X X X X X X X X X Numerically to nearest - 1 unit 0.01 unit .o1 unit .o1 unit .o1 unit 1 unit Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-6
48、L-F-315C b7 979777Li 0012433 3 L-F-315C 4.3 Test methods. 4.3.1 material it shall be not less than one linear yard in length and the full width of the material under test. One-half of the sample shall be put aside, protected from exposure to light, shall be examined in visible light to determine con
49、formance with requlrements specified in 3.2. protected half Of the sample shall be partially exposed to produce appro-tely one-half the maximum density, and then be completely developed on applicable equipment. for compliance with requirements specified in 3.2. Type VI-b in accordance with ANSI PH2.19, and shall be measured on a densitometer conforming to that specification.
