1、Page 2 “3.2,5.9 Badiogra?hic IasFecticn, Ti7e detona.l;cr shall meet: %he following requireinents when radiogra,phical distribution is unlimited bT Page I of 4- = I “s Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-D-LSLCLA (2) 13; e. The igniti
2、on assembly Dwg 1664935 or 2508062 as applicable sual1 be seated flush against the PETN charge in the cup assembly Dk-g 1664933 or 2508061 as applicable. betveen PETN charge and lead azide charge). or other fweign material within the detonator assembly. detonator assembly,“ (.O05 inch maxinuni gap a
3、llowable f. mers shall be no evidence of metal slivers, wire clippings There shall be no evidence of malformed parts within the g. Page 12 Para 4.5.6, second line, Change “(see 6.2.3)“ to I1(see 6.3.1)“. Page 14 After para 4.5.11, add: 114. 5.12 Radiographic Test (MI 12). The detonators. shall be te
4、sted Any detonator which fails to meet all in accordance with MILrSTD-202, Method 209 in the directions indicated on Dig 1261834 or 2508060 as applicable. the requirements of 3.2.5.9 shall be classified as defective. Acceptance shall b6 in accordance with Figure I through Figure 4 as applicable.Ir P
5、age I5 Change paragraph ri6.111 to %,211 and add: “f. Mod of detonator (I .I) g. Special markings required ( 5.4) h. That the safety precaution requirements of the Contractors Safety Manual for Ammunition, Explosives and Related Dangerous Material, BOD 4145.26, are applicable. NOTE: !en this specifi
6、cation is used as part of the description of work to be accomplished by a Government activity, the safety precaution requ3rements of Ammunition Ashore, OP 5, should be made applicable.“ . *I Add neu paragraph 6.1 as follows: Arming Delete Change to Change to “6.1 intended Use. Device Mark 2 Mods I,
7、3, and 5.“ Page 16 paragraph 6.3 in its entirety and change section 16.211 to 116.31. Detonators Mark 57 Mods I and 2 are used in Page 18 “;*MI O2 4.5.2“ “*M102(V) 4.5.21: MI07 (0.25% AQL) 4.5.7“ MI 07( V) 4.5.71 Change KIO8(Vj (0.25% AQL) 4.5. b. 1“ to 108(v) 4.5.8. II Aft er II *MI I I ( V 1- 3.2.
8、 4Ii Add lMI12 (sampling and acceptance h 4.5.12 acco-rdance with figure I, 2, 3, or 4)i1 ._ . 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-D-LILA (2) 13 = 7797706 0300252 7 W ,. MILD-1 91 51A (OS AMENDME3?T 2 . Page 20 ,. After “*Ml17 3.2.4
9、“ Add “MI12 (sampling and acceptance in 4.5.12 . accordance with Figure 1,2,3 or %)I1 Page 22 Figure 1, after “Dimensional and Material Inspectionlt.block add: Radiographic Inspection Sample Size = 50 11 Page 23 Figure 2, top block, change WK 50 Mod 1 or 2“ to IIMK 57 Mod 1 or Sit Both above and bel
10、ow the “Transportation Vibration“ block, add: Radiographic Inspect ion 4.5.12 Sample Size = 12 Page 24 Figure 3, top block, change “MX 50 Mod 1 or 211 to “MK 57 Mod i or 2“ After the I1Dimensional and Material Inspection1 block add: 100% inspection; In four blocks, change 100% Inspection“ to “100% I
11、nspection; reject 11 defectives“ . Page 25 Figure 4, top block, change “MK 50 Mod 1 or 2“ to I1M 57 Mod 1 or SI1 Both above and below the “Transportation Vibration block: add: Sample Size = 12 AC-O Re-1 11 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IH
12、S-,-,-frlIL-D-i9151A(C63 AMENDMENT 2 1 6.3 Changes from previous issue. Asterisks are not used in this revision .to $dentim &anges with respect to the prevLous issue due to the extensiveness of the changes. Preparing Activity : Navy - Os Project No. 1356-NO24 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
