1、 INCH-POUND MIL-DTL-22442/62A(AS) 14 May 2009 SUPERSEDING MIL-DTL-22442/62(AS) 14 April 2009 DETAIL SPECIFICATION SHEET CABLE ASSEMBLY, AIRCRAFT AUDIO This specification sheet is approved for use by the Naval Air Systems Command, Department of the Navy and is available for use by all Departments and
2、 Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-22442. 28.25 0.25FIGURE lA. Cable assembly P/N M22442/62-1 and P/N M22442/62-2. AMSC N/A 1 of 7 FSC 5995 Provided by IHSNot for ResaleNo reproduct
3、ion or networking permitted without license from IHS-,-,-MIL-DTL-22442/62A(AS) 2 FIGURE 1B. Cable assembly P/N M22442/62-1 and M22442/62-2 schematic diagram. APPLICABLE DOCUMENTS MIL-DTL-14072 - Finishes for Ground Based Electronic Equipment (Copies of these documents are available online at http:/a
4、ssist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA. 19111-5094.) Non-Government publications. The following document forms a part of this specification to the extent specified herein. Unless otherwise specified, the issu
5、es of these documents are those cited in the solicitation or contract. SOCIETY OF AUTOMOTIVE ENGINEERS INTERNATIONAL SAE-AMS 5901 - Steel, Corrosion Resistant, Sheet, Strip, and Plate 18 Cr- 8 Ni (SAE 30301), Solution Heat Treated (DoD Adopted) (Application for copies should be addressed to SAE Inte
6、rnational, 400 Commonwealth Drive, Warrendale, PA 15096.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-22442/62A(AS) 3 .577/16 HEX3/8-32 UNEF 2A.040 DIA.062 DIA7/16 HEX.423.270FIGURE 3A. CEP earphone connector, recessed SMB straight male j
7、ack, bulkhead rear mount, solder pot receptacle, gold plated, and terminal. FIGURE 3B. Terminal, lockwasher, thick brass, matte tin finish. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-22442/62A(AS) 4 0.3850.6250.093FIGURE 3C. ABS spacer f
8、or CEP connector (not included in P/N SK-1399-1). Black Shield Input from 47 OHM White Center DETAIL A 470 FIGURE 4. CEP earphone cable assembly schematic diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-22442/62A(AS) 5 REQUIREMENTS 1
9、 The cable (cord) shall be in accordance with M22442/35-3. 2. The weight of the cable assembly shall not be greater than 3 ounces. 3. The staycord shall be firmly attached to the connectors and strain relief. 4. The DC resistance shall be less than 2 ohms between the following contacts (Cable M2244
10、2/62-1 and M22442/62-2): (a) Contact 1 of P/N M642/14-01 and contact 2 of U-172/U. (b) Contact 2 of P/N M642/14-01 and contact 1 of U-172/U. (c) Contact 3 of P/N M642/14-01 and contact 2 of the left earphone contact and contact 2 of the right earphone contact. (d) Contact 5 of P/N M642/14-01 and con
11、tact 1 of the left earphone contact and contact 1 of the right earphone contact. (e) Contact 5 of P/N M642/14-01 and contact 2 of the CEP earphone connector contact. 5. The DC resistance shall be as specified between the following contacts (Cable M22442/62-1 and M22442/62-2): (a) Contact 3 of P/N M6
12、42/14-01 and contact 1 of the CEP earphone connector contact 470 ohms ( 20% tolerance). (b) Contact 1 and contact 2 of the CEP earphone connector contact 47 ohms ( 20% tolerance). 6. The CEP earphone connector (Applied Engineering Products, New Haven, CT. Dwg No. SK-1399-1) male bulkhead jack recept
13、acle shall be gold plated. 7. The cable assembly shall be tested in accordance with the tests listed in table I. 8. Cable assemblies M22442/62-1 and M22442/62-2 are identical with the exception that cable M22442/62-2 shall have a maximum length of 6.0 .25 from the outer shell of the U-384/U connecto
14、r to the crotched area. NOTES 1. All dimensions are in inches. 2. Tolerances are as follows: Metal parts .005, Molded sections .05. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-22442/62A(AS) 6 TABLE I. Tests. Inspection Requirement Paragra
15、ph Test ParagraphGroup I Qualification Tests Group II Quality Conformance Test 100% Group III Sample Testing Per 4.4.1 GROUP A (ALL SAMPLE UNITS) 1/ Visual & Mechanical Inspection 3.2 & 3.4 4.5.2 X X Soldering 3.4.18 4.5.2.1 X X Continuity 3.5.1 4.5.3 X X GROUP B Dielectric Withstanding Voltage 3.5.
16、2 4.5.4 X X Gauging 1/ 3.5.3 4.5.5 X X Bend Relief Flexibility 3.5.5 4.5.7 X X Pull and Twist Test 3.5.4 4.5.6 X X GROUP C Low Temperature Flexibility 3.5.6 4.5.8 X X Durability 1/ 3.5.7 4.5.9 X X GROUP D 1/ Salt Fog 3.6.2 4.6.2 X Vibration 3.6.4 4.6.4 X Humidity 3.6.5 4.6.5 X Thermal Shock 3.6.5 4.
17、6.6 X l/ Minimum tests for QPL retention (see 4.3.3) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-22442/62A(AS) 7 CONCLUDING MATERIAL Preparing activity: Navy - AS (Project 5995-2009-004) NOTE: The activity listed above was interested in t
18、his document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
