1、1 t I INCH-POUND I 30 September 1996 MIL-DTL-24800 DETAIL SPECIFICATION CLEANING COMPOUND - AQUEOUS - OXYGEN SYSTEMS COMPONENTS This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification establishes the requirements for
2、 an aqueous, inorganic cleaning compound to be used in immersion, ultrasonic, spray, and pumped cleaning of oxygen system piping and components. 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not in
3、clude documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements documented cited in sections 3
4、 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 specifications, standards, and handbooks. The following specifica- tions, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of thes
5、e documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation (see 6.2). Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this
6、document should be addressed to: Commander, SEA 03R42, Naval Sea Systems Command, 2531 Jefferson Davis Hwy, Arlington, VA 22242-5160 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC NIA FSC 6850 DISTRIBU
7、TION STATEMENT A. Approved for public release; distribution is unlimited. Licensed by Information Handling ServicesProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-ZqBOO 999950b ZO2b865 Bq8 MIL-DTL-24800 SPECIFICATIONS FEDERAL A-A-50433 QQ-A-2
8、 5 O QQ-A-250/4 - QQ-B- 6 5 4 - QQ-N-2 8 1 - - - QQ-N-2 8 6 - QQ-S-7 6 3 W-T-700 - DEPARTMENT OF DEFENSE MIL-T-1368 MIL-P-5425 MIL-P-5510 MIL-P-5516 MIL-H-5606 MIL-R-6855 MIL-M-7866 MIL-A-8625 MIL-S-8660 MIL-L-9000 MIL-C-15726 MIL-S-16216 MIL-T-16420 MIL-L-17331 MIL-H-17672 MIL-S-21923 MIL-G-22050 M
9、IL-F-22606 MIL-S-22698 MIL-S-23008 MIL-T-2 4 1 O 7 MIL-G-24139 DOD-G-24508 DOD-L-24574 MIL-P-24691 MIL-P-24691/3 - Grease, Sea Water Wash Resistant. Aluminum and Aluminum Alloy Plate and Sheet: Aluminum Alloy 2024, Plate and Sheet. Brazing Alloys, Silver. Nickel-Copper Alloy Bar, Rod, Plate, Sheet,
10、Strip, Wire, Forgings, and Structural and Special Shaped Sections. General Specification for. Nickel-Copper-Aluminum Alloy, Wrought, (UNS N05500). Steel Bars, Wire, Shapes, and Forgings, Corrosion Tube, Aluminum and Aluminum Alloy, Drawn, Seamless, Resisting. 5052, General Specification for. Tube an
11、d Pipe, Nickel-Copper Alloy, Seamless and Plastic Sheet, Acrylic, Heat Resistant. Packing, Preformed, Straight Thread Tube Fitting Boss, Type I Hydraulic (-65“ to 160F). Packing, Preformed, Petroleum Hydraulic Fluid Resistant, 160F. Hydraulic Fluid, Petroleum Base; Aircraft, Missile and Ordnance. Ru
12、bber, Synthetic, Sheets, Strips, Molded or Extruded Shapes, General Specification for. Molybdenum Disulfide, Technical, Lubrication Grade. Anodic Coatings For Aluminum and Aluminum Alloys. Silicone Compound, NATO Code Number S-736. Lubricating Oil, Shipboard Internal Combustion Copper-Nickel Alloy,
13、Sheet, Plate, Strip, Bar, Rod Steel Plate, Alloy, Structural, High Yield Strength Tube, Copper-Nickel Alloy, Seamless and Welded Lubricating Oil, Steam Turbine and Gear, Moderate Hydraulic Fluid, Petroleum, Inhibited. Synthetic Rubber Compound, Butadiene-Styrene Type, Ozone Resistant, for Low Temper
14、ature Service. Gasket and Packing Material, Rubber, for Use With Polar Fluids, Steam, and Air at Moderately High Temperatures. Flask Compressed Gas and End Plugs for Air, Oxygen and Nitrogen. Steel Plate, Shapes and Bars, Weldable Ordinary Strength and Higher Strength: Structural. Steel Castings, Al
15、loy, High Yield Strength (HY-80 and HY-100). Tube, Copper (Seamless), Copper Alloy Numbers ClOlOO, C10200, C10300, C10800, C12000, C12200, and C14200). Welded. Engine, High Output Diesel. and Wire. (HY-80 and HY-100). (Copper Alloy Numbers 715 and 706). Service. Grease, Multipurpose, Water Resistant
16、 Grease, High Performance, Multipurpose. (Metric) Lubricating Fluid for Low and High Pressure Oxidizing Gas Systems. Pipe and Tube, Carbon, Alloy and Stainless Steel, Seamless and Welded, General Specification for. Pipe and Tube, Corrosion-Resistant, Stainless Steel, Seamless or Welded. 2 Provided
17、by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24800 W 9999906 2026866 724 MIL-DTL-24800 . DEPARTMENT OF DEFENSE (Continued) MIL-P-25732 - Packing, Preformed, Petroleum Hydraulic Fluid MIL-G-27617 - Grease, Aircraft and Instrument, Fuel and Oxidizer
18、MIL-R-81828 - Rubber, Chlorosulfonated Polyethylene Elastomer, MIL-R-83248 - Rubber, Fluorocarbon Elastomer, High Temperature, MIL-R-83285 - Rubber, Ethylene-Propylene, General Purpose. MIL-P-83461 - Packing, Preformed, Petroleum Hydraulic Fluid Resistant, Limited Service at 275F (135C). Resistant.
19、Sheet and Molded Shapes, Ozone Resistant. Fluid, and Compression Set Resistant. Resistant, Improved Performance at 275F (135C). STANDARDS DEPARTMENT OF DEFENSE MIL-STD-1330 - Cleaning and Testing of Shipboard Oxygen, Nitrogen and Hydrogen Gas Piping Systems. (Unless otherwise indicated, copies of th
20、e above specifications, standards, and handbooks are available from the Standardization Documents Order Desk, 700 Robbins Avenue, Bldg 4D, Philadelphia, PA 19111-5094.) 2.2.2 Other Government documents. drawinas and Dublications. The following other Government documents, drawings and publications fo
21、rm a part of this document to the extent specified herein, Unless otherwise specified, the issues are those cited in the solicitation. DEPARTMENT OF DEFENSE SD-14 - Listing of Toxic Chemicals, Hazardous Substances, and Ozone-Depleting Chemicals. (Application for copies should be addressed to Office
22、of the Assistant Secretary of Defense for Economic Security, Standardization Program Division, 5203 Leesburg Pike, Suite 1403, Falls Church, VA 22041-3466.) NATIONAL AERONAUTICS AND SPACE ADMINISTRATION (NASA) NASA-WSTF-TP-629 - Test Protocol and Quality Assurance Program for the Navy Submarine Atmo
23、sphere Material Control Progr am. (Application for copies should be addressed to the Lyndon B. Johnson Space Center, White Sands Test Facility, Las Cruces, NM 88004.) NAVY ENVIRONMENTAL HEALTH CENTER (NEHC) NEHC-T“M92-2 - Reproductive Hazards in the Workplace: A Guide for Occupational Health Profess
24、ionals. (Application for copies should be addressed to the Navy Environmental Health Center, 2510 Walmer Ave, Norfolk, VA 23513.) ENVIRONMENTAL PROTECTION AGENCY (EPA) EPA-600-4-90-027 - Methods for Measuring the Acute Toxicity of Effluents and Receiving Waters to Freshwater and Marine Organisms. Ge
25、l Treated N-Hexane Extractable Material (SGT- HEM) by Extraction and Gravimetry (Oil and Grease and Total Petroleum Hydrocarbons). EPA-Method-1664 - N-Hexane Extractable Material (HEM) and Silica (Application for copies should be addressed to the Water Resource Center, Mail Code RC-4100, 401 M Stree
26、t, SW, Washington, DC 20460.) 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24800 9999906 2026867 660 MIL-DTL-24800 2.3 Non-Government Dublications. The following documents form a part of this specification to the extent specified herein.
27、 Unless otherwise specified, the issues of the documents which are DOD adopted shall be those listed in the issue of the DoDISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DoDISS are the issues of the documents cited in the solicitation (see 6.2).
28、 AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) ASTM B 148 - Standard Specification for Aluminum-Bronze Sand Castings. (DoD adopted) ASTM B 150 - Standard Specification for Aluminum Bronze, Rod, Bar, and Shapes. (DoD adopted) ASTM B 167 - Standard Specification for Nickel-Chromium-Iron Alloys (UN
29、S N06600, N06601, N006690, N06025, and N06045) Seamless Pipe and Tube. (DoD adopted) ASTM B 171 - Standard Specification for Copper-Alloy Plate and Sheet for Pressure Vessels, Condensers, and Heat Exchangers. ASTM B 209 - Standard Specification for Aluminum and Aluminum- Alloy, Sheet and Plate. (DoD
30、 adopted) ASTM B 221 - Standard Specification for Aluminum and Aluminum- Alloy Extruded Bars, Rods, Wire, Shapes, and Tubes. (DoD adopted) ASTM B 265 - Standard Specification for Titanium and Titanium Alloy Strip, Sheet, and Plate. (DoD adopted) ASTM B 337 - Standard Specification for Seamless and W
31、elded Titanium and Titanium Alloy Pipe. (DoD adopted) ASTM B 446 - Standard Specification for Nickel-Chromium- Molybdenum-Columbium Alloy (UNS N06625) Rod and Bar. ASTM D 471 - Standard Test Method for Rubber Property - Effects of Liquids. ( DoD adopted) ASTM D 501 - Standard Test Methods of Samplin
32、g and Chemical Analysis of Alkaline Detergents. (DoD adopted) ASTM D 512 - Standard Test Methods for Chloride Ion in Water. ( DoD adopted) ASTM D 543 - Standard Test Method for Resistance of Plastics to Chemical Reagents. ASTM D 1193 - Standard Specification for Reagent Water. (DoD adopted) ASTM D 1
33、248 - Standard Specification for Polyethylene Plastics Molding and Extrusion Materials. ASTM D 1280 - Standard Test Method of Total Immersion Corrosion Test for Soak Tank Metal Cleaners. ASTM D 1292 - Standard Test Method for Odor in Water. ASTM D 1331 - Standard Test Methods for Surface and Interfa
34、cial ASTM D 1457 - Standard Specification for Polytetrafluoroethylene Tension of Solutions of Surface-Active Agents. (PTFE) Molding and Extrusion Materials. (DoD adopted) Chloride) (PVC) Compounds and Chlorinated Poly (Vinyl Chloride) (CPVC) Compounds. (DoD adopted) and Extrusion Materials. (DoD ado
35、pted) Polymer and Copolymer Molding and Extrusion Compounds. (DoD adopted) with Liquid Oxygen (Impact Sensitivity Threshold and Pass-Fail Techniques). Water. ( DoD adopted) Hydrocarbons in Water. Unfilled and Reinforced Material. ASTM D 1784 - Standard Specification for Rigid Poly (Vinyl ASTM D 2116
36、 - Standard Specification for FEP-Fluorocarbon Molding ASTM D 2287 - Standard Specification for Nonrigid Vinyl Chloride ASTM D 2512 - Standard Test Method for Compatibility of Materials ASTM D 2579 - Standard Test Method for Total Organic Carbon in ASTM D 3921 - Standard Test Method for Oil and Grea
37、se and Petroleum ASTM D 3935 - Standard Specification for Polycarbonate (PC) 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- _ MIL-DTL-24800 9999906 2026868 ST7 W MIL-DTL-24800 ASTMs (Continued) ASTM D 4052 - Density and Relative Density of Liquid
38、s by Digital Density Meter. ASTM D 4066 - Standard Specification for Nylon Injection and Extrusion Materials (PA). (DoD adopted) ASTM D 4101 - Standard Specification for Propylene Plastic Injection and Extrusion Materials. (DoD adopted) ASTM D 4181 - Standard Specification for Acetal (POM) Molding a
39、nd Extrusion Materials. (DoD adopted) ASTM D 4281 - Standard Test Method for Oil and Grease (Fluorocarbon Extractable Substances) by Gravimetric Determination. Inorganic Carbon in High Purity Water by Ultraviolet (UV) or Persulfate Oxidation, or Both, and Infrared Detection. ASTM E 70 - Standard Tes
40、t Method for pH of Aqueous Solutions With the Glass Electrode. (DoD adopted) ASTM F 483 - Standard Test Method for Total Immersion Corrosion Test for Aircraft Maintenance Chemicals. ASTM F 1104 - Standard Test Method for Preparing Aircraft Cleaning Compounds, Liquid Type, Water Base, For Storage Sta
41、bility Testing. ASTM G 72 - Standard Test Method for Autogenous Ignition Temperature of Liquids and Solids in a High-pressure Oxygen-Enriched Environment. ASTM D 4779 - Standard Test Method for Total, Organic, and (Application for copies should be addressed to the American Society for Testing and Ma
42、terials, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.) 2.4 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein, the text of this document takes precedence. Nothing in the specification, however, shall supersede applicable
43、 laws and regulations unless a specific exemption has been obtained. 3- REQUIREMENTS 3.1 First article. When specified (see 6.2), a sample shall be subjected to first article inspections in accordance with 4.3. 3.2 ComDosition. The cleaning compound shall be an aqueous, inorganic solution meeting th
44、e performance characteristics of 3.4. The cleaning composition shall not intentionally contain carbon-hydrogen bonded material, or material that is not completely soluble. Examples of prohibited material include polar organic surface active agents, polar solvents, or dispersable fluorocarbon surface
45、 active agents. If any of these prohibited materials are present as a result of being a trace impurity in another ingredient(s), the concentration shall not exceed the limits specified in 3.4.3. 3.3 Naw oxvaen cleaner INOC). 3.3.1 NOC composition. The NOC composition shown in table I meets the perfo
46、rmance characteristics of 3.4 when manufactured as specified in 3.3.2 and packaged as specified in 5.1. 3.3.2 NOC manufacture. Unless otherwise approved by the preparing activity, NOC shall be blended in welded stainless steel tanks; piping and components shall be stainless steel; hoses shall be Tef
47、lon lined; and gaskets shall be Viton or Teflon. The cleaning compound shall be filtered through a 0.1 micron membrane filter. Filters shall be constructed of stainless steel, Teflon, polysulfone, or polyethylene, and shall contain no plasticizer, adhesive or other extractable material, Production o
48、f the cleaning compound shall utilize dedicated equipment which shall not be used for any other purpose. A recirculating pump, or other method approved by the preparing activity, shall be used to ensure complete blending of the cleaning compound. The minimum blending time when recirculating NOC thro
49、ugh a pump shall be determined as follows: 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24800 D 9999906 202bBb9 433 D MIL-DTL-24800 . Minimum blending time = (Oe693/W)(V)(5) where: W = pump flow rate in gallons per minute V = batch tank volume in gallons 3.3.3 NOC raw materials. Raw materials used or the NOC composition cleaning compound shall meet the requirements shown in table II when tested as specif
