1、MI L-STD-13224000 (NAVY) MILITARY STANDARD A AUGUST im UNIT LOADS FOR DOMESTIC AND OVERSEAS SHIPMENT TYPICAL LOADS 1. SCOPE 1.1 SCOPE. THISSLASH NUMBERED DOCUMENT PROVIDES GUIDANCE TO ENABLE AN ACTIVITY TO CONSTRUCT APPROVED UNIT LOADS WHEN NO SPECIFIC SLASH NUMBER DOCUMENT EXISTS FOR THE ITEM(S) TO
2、 BE PALLETIZED. 1.2 RESTRICTIONS. THE USE OF THIS SLASH NUMBERED DOCUMENT IS LIMITED TO CONVENTIONAL AMMUNITION AND EXPLOSIVE ITEMS PACKAGED IN APPROVED CONTAINERS. IT SHALL NOT BE USED FOR LOOSE OR IRREGULAR SHAPED ITEMS THAT REQUIRE SPECIAL PURPOSE PALLETS OR METAL PALLET ADAPTERS TO CONSTRUCT THE
3、 UNIT LOAD. 1.2.1 THE USE OF THISSLASH NUMBERED DOCUMENT IS LIMITED TO THE OCCASIONAL REQUIREMENT TO PALLETIZE ITEMS NOT COVERED BY SPECIFIC MIL-STD-1322 SLASH NUMBERED DOCUMENTS. RECURRING REQUIREMENTS REQUIRE THE DEVELOPMENT OF A SPECIFIC MIL-STO SLASH SHEET. REQUESTS FORA SPECIFIC SLASH SHEET SHO
4、ULD BE SENT TO COMMANDING OFFICER, NAVAL WEAPONS STATION MRE, COLTS NECK, N.J. 01722 ATTN: NAVAL WEAPONS HANDLING CENTER (NWHC). 2. DOCUMENT USE REQUIREMENTS 2.1 GENERAL. THE REQUIREMENTS OF THIS SLASH NUMBERED DOCUMENT AND THE GENERAL DOCUMENT MIL-STD-1322 (NAVY) SHALL BE FOLLOWED. 2.1.1 USE OF THI
5、S SLASH SHEET. THE EXAMPLES SHOWN IN THIS SLASH NUMBERED SHEET ARE TYPICAL PROCEDURES. CONSTRUCTION OF THE UNIT LOAD FOR THE ITEM(S) TO BE PALLETIZED SHOULD FOLLOW THE GENERAL PRINCIPLES AND REQUIREMENTS OF THE TYPICAL UNIT LOADS THAT ARE SHOWN QN THE FOLLOWING PAGES, THE TYPICAL UNIT LOAD FOR AN IT
6、EM WHLCH MOST CLOSELY RESEMBLES THE ITEM TO BE PALLETIZED SHOULD BE USED. 2.1.2 TYPICAL UNIT LOADS NOT USEABLE. WHEN THE ITEMS SHOWN AS TYPICAL UNIT LOADS AR NOT SUFFICIENTLY LIKE THE ITEM TO BE PALLETIZED, THE PUBLISHED MIL-STD-1322 (NAVY) DASH SHEETS (INCLUDING ALL WR-53 SLASH SHEETS NOT SUPERSEDE
7、D) SHOULD BE EXAMINED AND THE ONE WITH THE ITEM MOST CLOSELY RESEMBLING THE ITEM TO BE PALLETIZED SHOULD BE USED. rt U.S. GOVERNMENT PRINTING OFFICE1981-505-022/7398 I SC 814 - REQUIREMENTS FOR CONSTRUCTION OF THIS UNI” LOAD SHALL CONSIST OF THIS DOCUMENT AND THE LATEST AUTHORIZED AND RELEASED FOR T
8、HE PREPARATION OF UNIT LOADS FOR DOMESTIC AND OVERSEAS SHIPPING, HANDLING AND STORAGE. ISSUE OF MIL-STD-1322 (NAVY) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-13 22 -1 000 (NAVY) 2.1.3 ASSISTANCE. WHEN IT HAS BEEN DETERMINED THAT THE INS
9、TRUCTIONS OF PARAGRAPHS 2.1.1 AND 2.1.2 DO NOT PROVIDE SUFFICIENT GUIDANCE, ADDITIONAL ASSISTANCE MAY BE REQUESTED FROM THE NAVAL WEAPONS STATION EARLE (NWHC), AUTOVON 449-7692, 7693, 7691. 3. MATERIAL REQUIREMENTS 3.1 GENERAL. UNLESS OTHERWISE SPECIFIED, ALL MATERIAL USED IN THE CONSTRUCTION OF THE
10、 UNIT LOADS SHALL BE AS SPECIFIED IN THE GENERAL PALLETIZING DOCUMENT MIL-STD-1322 (NAVY). 3.2 PALLETS, ONLY STANDARD SIZE WOOD PALLETS (40 x 48 AND 35 x 45 1/2 SHALL BE USED, MK 3 AND MK12 METAL PALLETS MAY BE USED WHEN OVERALL LOGISTIC COST SAVINGS OWEIGH THE HIGHER COST OF METAL PALLETS. 3.3 STEE
11、L STRAPPING. UNLESS OTHERWISE SPECIFIED 3/4 INCH STRAPPING MAY BE USED FOR UNIT LOADS WITH A GROSS WEIGHT OF LESS THAN 2800 LBS. WHEN THE UNIT LOAD GROSS WEIGHT EXCEEDS 2800 LBS., 1 1/4 INCH STRAPPING SHALL BE USED. 4. CONSTRUCTION REQUIREMENTS 4.1 ITEM PLACEMENT ON PALLET. UNIT LOADS SHALL ONLY BE
12、MADE UP IN FULL LAYERS THAT ARE CENTERED LENGTHWISE AND WIDTHWISE ON THE PALLET. THE UNIT LOAD MAY CONSIST OF ONE OR MORE LAYERS AS APPROPRIATE. QUANTITIES OF ITEMS WHICH DO NOT EQUAL A FULL LAYER SHALL BE SHIPPED, HANDLED AND STORED/STOWED LOOSE (NOT UNITIZED). 4.1.1 ITEM SHOULD BE ARRANGED ON THE
13、PALLET TO FORM SOLID, COMPACT LAYERS. ITEMS IN PLACE ON A PALLET SHOULD REMAIN IN PLACE WITHOUT ADDITIONAL SUPPORT. OVERHANG IN EXCESS OF 3 INCHES SHOULD BE AVOIDED. 4.2 SIZE AND WEIGHT. UNIT LOADS SHOULD NOT EXCEED 45 INCHES IN WIDTH, 54 INCHES IN ISNGTH AND 47 INCHES IN HEIGHT. DIMENSIONS MAY BE I
14、NCREASED IF MANDATED BY THE SIZE OF THE ITEM AND THE LOGISTIhHIPPING CYCLE IS SUCH THAT NO PROBLEMS WILL BE ENCOUNTERED DURING HANDLING, SHIPPING, AND STORAGE/STOWAGE. THE GROSS WEIGHT OF THE UNIT LOAD SHOULD NOT EXCEED 3ooo POUNDS. 4.3 UNDERHANG, UNDERHANG SHALL NOT BE PERMITTED. SPACERS AND BATTEN
15、S SHALL BE USED TO FILL OUT THE UNIT LOAD SO THAT THE OVERALL NOMINAL PLAN VIEW DIMENSIONS ARE FLUSH WITH THE PALLET DIMENSIONS. 4.4 TIE-DOWN STRAPS. UNLESS OTHERWISE SPECIFIEDALL UNIT LOADS SHALL HAVE A MINIMUM OF FOUR TIE-DOWN STRAPS WITH TWO STRAPS RUNNING THE LENGTH OF THE UNIT LOAD AND TWO STRA
16、PS RUNNING THE WIDTH OF THE UNIT LOAD. 4.4.1 ADDITIONAL STRAPS SHALL BE USED AS NECESSARY TO PROVIDE POSITIVE RESTRAINT OF ALL ITEMS. THIS MAY BE ACCOMPLISHED BY USE OF ADDITIONAL TIE-DOWN STRAPS, HORIZONTAL STRAPS OR BOTH. 4.5 WOOD PALLET ADAPTERS. CONTAINERS OTHER THAN RECTANGULAR SHAPE SUCH AS CY
17、LINDRIC4L SHAPED CONTAINERS (DRUMS) OFTEN REQUIRE PALLETIZING. THIS REQUIRES THE USE OF ADAPTERS TO ASSIST IN SECURING THE DRUMS TO THE PALLET. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-1322 -1000 il W 7997921 0071344 7 = MIL-STD-13 22-
18、1000 (NAVY) 4.5.1 WHEN REQUIRED, WOOD ADAPTERS MAY BE CONSTRUCTED AND USED PROVIDED THE ITEM IS NOT RESTRICTED AS SPECIFIED IN PARAGRAPH 1.2. 4.5.2 THE EXAMPLES USED IN THIS DASH SHEET AND OTHER MIL-STD-1322 DASH SHEETS (AND WR-53 SLASH SHEET) SHOULD BE USED TO ASSIST IN CONSTRUCTING WOOD ADAPTERS.
19、5. MARKINGS 5.1 THE UNIT LOAD SHALL BE MARKED IN ACCORDANCE WITH THE REQUIREMENTS OF THE GENERAL WCUMENT MIL-STD-1322 (NAVY). 6. INSPECTION 6.1 THE COMPLETED UNIT LOAD SHALL BE INSPECTED IN ACCORDANCE WITH PARAGRAPH 4.9 OF THE GENERAL DOCUMENT MIL-STD-1322 (NAVY). 1 X 4 BATTEN (4 PLACES) UNIT LOAD W
20、ITH UNDERHANG CORRECTED USING BATTENS (2 SIDES) AND CONTAINERS ARRANGED AT RIGHT ANGLES Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIGSTD-1322-1000 (NAVY) CONTAINER 2 X 4 BATTEN (4 PLACES) STAPLE (12 REQD) . (WOOD PALLET) DETAIL UNIT LOAD WITH U
21、NDERHANG (2 SIDES) CORRECTED USING BATTENS CONTAINERS ARRANGED “CHIMNEY PATTERN“ Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-M IL-STD-1322-1OOO (NAVY) MK 1 MUNITION BOX DETAIL UNLT LOAD WITH UNDERHANG (4 SIDES) CORRECTED USING BATTENS AND SIDE FR
22、AMES Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-1322-1000 (NAVY) lX4J 1x4 SPACER FRAME ASSEMBLY v 1 REQUIRED STAPLE DETAIL UNIT LOAD WITH SPACER FRAME ASSEMBLY USED TO PREVENT UNDERHANG PAGE 6 i WOOD PALLET Provided by IHSNot for ResaleN
23、o reproduction or networking permitted without license from IHS-,-,-PROTECTOR DETAIL UNIT LOAD WITH BOXES ARRANGED MODIFIED “CHIMNEY PATTERN“ PAGE 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_- MIL-STD-1322 -1000 BI 7777733 0071347 b W 20 l/4 D
24、IA. DRUM PAGE 8 m-UD-13 22-1000 (NAVY) 1 X 6 (NAIL W-3/8d BOX NAILS PER JOINT TOP FRAME ASSEMBLY (i REQUIRED) 1 X 6 (NAIL W-3/d BOX NAILS PER JOINT) BOTTOM FRAME ASSEMBLY (i REQUIRED) UNIT LOAD OF DRUMS USING WOOD ADAPTERS Provided by IHSNot for ResaleNo reproduction or networking permitted without
25、license from IHS-,-,- NIL-STD-I322 -IO00 BI 77977II 0073350 2 MIL-STD-1322-1000 (NAVY) .ET DETAIL 0 UNIT LOAD WITH NO UNDERHANG PAGE 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-SID-1322-1000 (NAVY) STRAP THREADING DETAIL CONTAINER DETAIL UN
26、IT LOAD ON MK 3 METAL PALLET (SEE PARAGRAPH 3.2) PAGE 10 i , Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-M Il- STD-13 229-1000 (NAVY) STRAP THREADING DETAIL DETAIL 0 UNIT LOAD ON MK 12 METAL PALLET (SEE PARAGRAPH 3.2) I REVIEW ACTIVITY: NAW-OS PREPARING ACTIVITY: NAVY-OS (PROJECT N0.8140-N471) PAGE II Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
