1、MIL-STD-LhOC NOTICE L 4 m 9999931 00704Lb 2 m A-, MIE-STB-1608C 17 August 1988 SPER8EDING MIL-STD-1608B 16 January 1984 FSC 8410 ANSC N/A DISTBIBTIQN STATEMENT A. Approved for public r%ea%e, distribution is mbiiriited o Provided by IHSNot for ResaleNo reproduction or networking permitted without lic
2、ense from IHS-,-,- 5 s MIL-STD-360C NOTICE 3 L1 m 7779733 0070Y17 4 W , MIL-STD-1608C I FOREMFl 1. This Military Standard is approved for use by all Departments and Agencies of the Department of Defense. 2, Beneficial comments (recommendations, additions, deletions) and any pertinent data which may
3、be of use in improving this document should be addressed to: Officer in Charge, Navy Clothing and Textile Research Facility, 21 Strathmore Road, Natick, MA 01760-2490 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by
4、letter. 3. This document supplements the military specifications listed below. It provides a standard description for defects and standardizes examination . cequirements. SpeciEication MIL-C-21084(MC) MIL-C-21085(MC) MIL-U-28946 (MC) MIL-C-29121(NU) MIL-C-29124 (No) MTL-C-B427(MC) MI-C-29453( MC) MI
5、L-C-441OI.(GL) MIL-C-4 4 3 7 9 ( GL ) MIL-(387160 (USAI?) Title Lc_ Coat, Womens, Wool, Gabardine, Blue Coats, womens Wool, Polyesterflool Uniform, Womens; White; Dress (Officers) Coat, Womans, Service, White Coat, Womans, Blue, Dress Coat , Voxen fi Coat, Woran s , Wool/poly Gabardine, Blue Coat, W
6、oxms, Classic Design, Poiyesterflool Coat, Woments: Classic Design, Polyesterflool, AG-344, Fusible Coat, womans, (Pant Suit) a ii Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- , .- . MLL-STD-3bOC NOTICE 3 4 W 7777733 0070435 O W NOTICE OF rzJ MIL
7、ITARY STlWRD PROVISIONS FOR EVALUATING QALITy OF CQATS, mfS, DRESS To ALL HOLDERS OF MIL-STD-1608C: 1-GZ:pouND;1 MIL-STD-1608C NOTICE 1 4 June 1990 1. THE FOLLOWING PAGES OF MIL-STD-1608C HAVE BEEN REVISED AND SUPERSEDE THE PAGES LISTED: NEW PAGE DATE SUPERCEDED PAGE DATE Cover sheet 17 August 1988
8、Cover sheet REPRINTED WITHOUT CHANGE ii 4 June 1990 ii 17 August 1988 iii 17 August 1988 ii 17 August 1988 Leave blank iii 17 August 1988 2. RETAIN THIS NOTICE AND INSERT BEFORE TABLE OF CYrJTENTS. 3. Holders of MIL-STD-1608C will verify that page changes and additions indicated above have been ente
9、red. This notice page will be retained as a check sheet. This issuance, together with appended pages, is a separate publication. Each notice is to be retained by stocking points until the military standard is completely revised or canceled. Custodians : Navy- NU Air Force - 11 AT- GL Preparing activ
10、ity: Navy - NU (Project No. 8410-0744) Review activities:. Navy - MC Air Force - 99, 82 DLA - CT AMSC N/A FSC 8410 DISTRIBIPTION STATEMENT A. Approved for public release, distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- far
11、agragh 1. 1.1 1.2 1.2.1 2. 2.1 2.1.1 2.2 2.3 3. 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 4. 5. 5.1 5.2 5.3 5.4 5.5 5.5.1 5.5.2 5.5.3 5.5.4 5.6 5.6.1 5.7 5.8 6. 6.1 6.2 6.3 I II III IV SCOPE Scope DEFINITIONS Fabris defects Knots and s1ub6: Quality Assurance Terms and Procedures Open sem Defective button Outs
12、ide-Inside Raw edge Puckering DETAIL REQU1-S Purpose Inspection procedures Initiation sf irispection Continuation of inspection witching procedures Normal to tightened Tightened to norm1 Normal to reduced Reduced to normal. End item examination mamination for Table IV nieasiirab%e defects Dimensiona
13、l examination Exmination of packaging requirements INFORMATION FOR GWIWCE ONLY Intended use Subject term (key word) listing Changes from previous issue Sapling Prvisions Claesifieatisn of defects Selected defects Measurable defects F 1 1 1 3 4 4 4 4 4 4 4 4 4 5 5 5 6 6 25 25 25 25 7 0 24 25 iib c -
14、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-3608C L( U 7474733 0082646 L MIL-STD-1608C 1. SCOPE 1.1 Scope. The scope of this standard is to provide standardized provisions for evaluating the quality of womens dress coats. 1.2 Application.
15、 This standard will be made applicable to contracts by references in the appropriate coat specifications. These documents require: (a) As a final step in the contractors production control plan before formation of a lot, each coat shall be buttoned on a model form and examined for selected defects.
16、and (b) A coat containing a selected defect shall not be included in the end item lot. Selected defects are those defects listed in Table II as asterisk (*) defects. The selected asterisk defects are listed individually in Table III. The examination for selected defects will also include the measure
17、ment of those selected defects identified in Table IV. 1.,2.1 Model form. The model forms (for the selected defects examination specified in 1.2, and for examination of defects XV through XXVI in Table II, Classification of defects) shall be womens forms conforming to the measurements specified belo
18、w. The coat sizes listed shall be examined on the appropriate model form size as specified below. Model form measurements Coat size Model form size Bust - i/ Waist - 2/ Hip 2/ 3, 4, 5 4 33 24 34 6, 7, 8, 9, 10 6 11, 12, 13, 14, 15 12 16, 17, 18, 19 16 20, 22 20 34 25 35 37 28 38 40 31 41 43-1 /2 34-
19、1 /2 45 i/ Tolerance + 1 inch 2/ Tolerance 1/2 inch - - - 2. REFERENCE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks forms a part of this document to the extent specified herein. Unless otherwise specified,
20、the issue of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation. 1 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I_- - -I-
21、.- ._ MIL-STD-LbOC 84 9LL 0082647 3 W MIL-STD-1608C STANDARD FEDERAL FED-STD-4 - Glossary of Fabric Imperfections MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by MIL-STD-1 O9 Attributes - Quality Assurance Terms and Definitions (Copies of specifications, standards, drawings,
22、and publications required by contractor in connection with specific procurement functions should be obtained from the procuring activity or as directed by the contracting officer .) 2.2 Other publications, The following document(s) form a part of this standard to the extent specified herein. Unless
23、otherwise specified, the issues of the documents which are DOD adopted shall be those listed in the issue of the DODISS specified in the solicitation. Unless otherwise specified, the issues of documents not listed in DODISS shall be the issue of the nongovernment documents which is current on the da
24、te of the solicitation. AATCC Photographic Comparative Rating of Single and Double Needle Seams (Method 88B, Two photos) (Application for copies should be address to The American Association of Tsxtile Chemists and Colorists, P.O. Box 12215, Research Triangle Park, NC 27709-9989). (Nongovernment sta
25、ndards are generally available for reference from libraries. They are also distributed among nongovernment standards bodies and using Federal Agencies .) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this standard s
26、hall take precedence. Nothing in this standard, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. 3. DEFINITIONS 3.1 Fabric defects. The fabric defect definitions applicable to the standard are described in FED-STD-4. Fabric defects shall be clea
27、rly visible when examined at a distance of 3 feet. 3.2 Knots and slubs. Only knots and slubs that exceed the limits specified in the basic cloth specification and are clearly visible when examined at a distance of 3 feet shall be scored as defects in evaluating quality of coat. 3.3 Quality assurance
28、 terms and procedures. Quality assurance terms and procedures, when applicable, shall be in accordance with MIL-STD-105 and MIL-STD-109. O n O 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-1608C 3.4 Open seam. The seam shall be classified
29、 open when one or more stitches joining a seam are broken or runoff, or when two or more continuous skipped or runoff stitches occur. Double stitched seams are considered open when one or both rows of the stitching are open. 3.5 Defective button. A button shall be considered defective when it has a
30、sharp, rough, cracked or split edge; scratches, dents, blemishes, imbedded foreign matter, loose shank, loose shell; badly shaded or poorly plated. 3.6 Outside-Inside. The terms “outside” and “inside“ as used in this standard for defects I, II, and IV (see Table 11) are defined as follows: Outside -
31、 Any part of coat that is visible when the completely buttoned coat is observed on the model form (including undersleeve). inside - Any part of coat that is not visible when the completely buttoned coat is observed on the model form. The terms “outside“ and “inside“ as used in this standard for any
32、defects other than I, II, and IV are defined as follows: Outside - Any part, seam or stitching that appears on the outer coat. This includes under the collar (including undercollar), under the shoulder loops and under the pocket flaps. Inside - Any part, seam, or stitching that does not appear on th
33、e outer coat b 3.7 Raw edge. A raw edge is defined as any edge not finished as specified including any protruding edge on the outside of the coat. 3.8 Puckering. In the course of the sampling examination, seams suspected of being puckered shall be examined at a distance of 3 feet in comparison with
34、the AATCC Photographic Comparative Rating (see 2.2), method 88B for seams. Puckering on a major portion of the suspected seam that equals or is worse than rating 3 for single needle seams or double needle seams shall be scored as a puckered seam. 4.GENEKAL REQUIREMENTS This section is not applicable
35、 to this standard. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- - ._ -_ MIL-STD-LbOC 84 99999311 002b49 7 W MIL-STD-1608C 5. DETAIL REQUIREMENTS 5.1 Purpose. This standard contains the provisions for end item examination, dimensional examinatio
36、n, and packaging inspection for coats. If there are any inconsistencies between the requirement of the appropriate specification and the provisions of the standard, the specification shall control, This standard assigns to listed defects, point values of 1, 2, or 3 depending on a degree of severity.
37、 The higher point values are assigned to those defects having more detrimental effect on the appearance or serviceability of the item. The defects indicated by an asterisk (*) in Table II are those defects having the most detrimental effect on appearance or serviceability of the item. 5.2 Inspection
38、 procedures. Inspection prbcedures shall be specified in MIL-STD-105, except where otherwise indicated in this document. 5.3. Initiation of inspection. Normal inspection shall be used at the start of inspection unless otherwise directed by the procurement quality assurance element administrating the
39、 contract. 5.4 Continuation of inspection. Normal, tightened, or reduced inspection shall continue unchanged on successive lots except where switching procedures in 5.5 require change. 5.5 Switching procedures. 5.5.1 Normal to tightened, When normal inspection is in effect, tightened inspection shal
40、l be instituted when two out of five consecutive lots have been rejected on original inspection (i .e., ignoring resumbi tted lots for this procedure). 5.5.2 Tightened to normal. When tightened inspection is in effect, normal inspection shall be instituted when five consecutive lots have been consid
41、ered acceptable on original inspection. 5.5.3 Normal to reduced. When normal inspection is in effect, reduced inspection shall be instituted providing that all of the following conditions are satisfied: (a) The preceding 10 lots have been on normal inspection and none have been rejected on original
42、inspection; and (b) The total number of points for 3 and 2 point defects in the samples from the preceding 10 lots is equal to or less than sixty percent of the total maximum acceptable point values for 3 and 2 point defects from the preceding 10 lots; and (c) The total number of points for 3, 2, an
43、d 1 point defects in the sample from the preceding 10 lots is equal to or less than seventy-five percent of the total maximum acceptable point values for 3, 2, and 1 point defects from the preceding 10 lots; and 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license f
44、rom IHS-,-,-MIL-STD-LhOC L( 77777LL 0082b50 3 M MIL-S TD- 1608C (d) Production is at a steady rate; and (e) Reduced inspection is considered desirable by the procurement quality assurance element administrating the contract. 5.5.4 Reduced to normal. When reduced inspection is in effect, normal inspe
45、ction shall be instituted if any of the following occur on original i ns pec t i on : (a) A lot is rejected; or (b) A lot is considered acceptable but exceeds the applicable first value (see NOTE to Table I); or * (e) Production becomes irregular or delayed; or (d) Other conditions warrant that norm
46、al inspection be instituted. e 29 5.6 End item examination. The dress coats shall be buttoned on a model form or laid out flat on a table as required in Table II for inspection. The dress coats shall be examined and all defects shall be penalized as indicated in Table II of this standard. The sample
47、 size shall be as specified in Table L. The sample unit shall be one finished coat, The lot shall be unacceptable if: a. The point value for 3 and 2 point defects exceeds the applicable maximum acceptable point value. OR b. The point value for total (3, 2, and 1 point) defects exceeds the applicable
48、 maximum acceptable point value. OR C. The number of selected defects (asterisk -k defect) exceeds the maximum allowed for the sample size (see Table I). 29 5.6.1 Examination for measurable defects (Table IV). As a part of the end iteni examination, the applicable number of dress coats specified bel
49、ow shall be measured to determine the presence of defects listed in Table IV. At least one coat from each size in the lot shall be included in the sample. When the number of sizes in the lot exceeds the sample size, the sizes to be included in the sample shall be randomly selected from among all the sizes. The sample shall be examined for all end item characteristics
