NBN C 68-207-1986 5000 《电压直至37kv的能源输送绝缘电缆的附属装置 外部电压UO U超过 0 6 1 kV 直至20，8 36kV》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

AGMA 01FTM7-2001 Chemically Accelerated Vibratory Finishing for the Elimination of Wear and Pitting of Alloy Steel Gears《合金钢齿轮的磨损和点蚀的消除用化学加速振动修整》.pdf

AGMA 01FTM8-2001 The Effect of Spacing Errors and Runout on Transverse Load Sharing and the Dynamic Factor of Spur and Helical Gears《正齿轮和螺旋齿轮的横向负载分配上间距误差和弯曲及动力因素的影响》.pdf

AGMA 01FTM9-2001 New opportunities with Molded Gears《浇注齿轮的新时机》.pdf

AGMA 01FTMS1-2001 Optical Technique for Gear Contouring《齿轮造型用光学技术》.pdf

AGMA 02FTM1-2002 The Effect of Chemically Accelerated Vibratory Finishing on Gear Metrology《齿轮度量衡学的化学加速振动修整的影响》.pdf

AGMA 02FTM10-2002 Comparison in Rating Trends in AGMA versus ISO《AGMA对ISO的等级趋势比较》.pdf

AGMA 02FTM11-2002 A Gear Design Optimization Procedure that Identifies Robust Minimum Stress and Minimum Noise Gear Pair Designs《确认坚固、最低应力与最小噪声齿轮副设计的齿轮设计优化程序》.pdf

AGMA 02FTM2-2002 Development and Application of Computer-Aided Design and Tooth Contact Analysis of Spiral-Type Gears with Cylindrical Worms《带圆柱蜗杆螺旋型齿轮的计算机辅助设计和齿面接触分析的开发与应用》.pdf

AGMA 02FTM3-2002 Application of Statistical Stability and Capability for Gear Cutting Machine Acceptance Criteria《齿轮切割机验收标准用性能和统计学稳定性的应用》.pdf