1、NEMA Standards PublicationNational Electrical Manufacturers AssociationANSI C136.11-2011 (R2016)Roadway and Area Lighting Equipment Multiple Parallel Wired Sockets 2017 National Electrical Manufacturers Association ANSI C136.11-2011 (R2016) Reaffirmation of ANSI C136.11-2011American National Standar
2、d for Roadway and Area Lighting Equipment Multiple Parallel Wired Sockets Secretariat: National Electrical Manufacturers Association Approved June 27, 2017 American National Standards Institute, Inc. ANSI C136.11-2011 (R2016) Page ii 2017 National Electrical Manufacturers Association NOTICE AND DISC
3、LAIMER The information in this publication was considered technically sound by the consensus of persons engaged in the development and approval of the document at the time it was developed. Consensus does not necessarily mean that there is unanimous agreement among every person participating in the
4、development of this document. ANSI standards and guideline publications, of which the document contained herein is one, are developed through a voluntary consensus standards development process. This process brings together volunteers and/or seeks out the views of persons who have an interest in the
5、 topic covered by this publication. While NEMA administers the process to promote fairness in the development of consensus, it does not write the document and it does not independently test, evaluate, or verify the accuracy or completeness of any information or the soundness of any judgments contain
6、ed in its standards and guideline publications. NEMA disclaims liability for any personal injury, property, or other damages of any nature whatsoever, whether special, indirect, consequential, or compensatory, directly or indirectly resulting from the publication, use of, application, or reliance on
7、 this document. NEMA disclaims and makes no guaranty or warranty, expressed or implied, as to the accuracy or completeness of any information published herein, and disclaims and makes no warranty that the information in this document will fulfill any of your particular purposes or needs. NEMA does n
8、ot undertake to guarantee the performance of any individual manufacturer or sellers products or services by virtue of this standard or guide. In publishing and making this document available, NEMA is not undertaking to render professional or other services for or on behalf of any person or entity, n
9、or is NEMA undertaking to perform any duty owed by any person or entity to someone else. Anyone using this document should rely on his or her own independent judgment or, as appropriate, seek the advice of a competent professional in determining the exercise of reasonable care in any given circumsta
10、nces. Information and other standards on the topic covered by this publication may be available from other sources, which the user may wish to consult for additional views or information not covered by this publication. NEMA has no power, nor does it undertake to police or enforce compliance with th
11、e contents of this document. NEMA does not certify, test, or inspect products, designs, or installations for safety or health purposes. Any certification or other statement of compliance with any health- or safety-related information in this document shall not be attributable to NEMA and is solely t
12、he responsibility of the certifier or maker of the statement. ANSI C136.11-2011(R2016) Page i AMERICAN NATIONAL STANDARD Approval of an American National Standard requires verification by The American National Standards Institute, Inc. (ANSI) that the requirements for due process, consensus, and oth
13、er criteria for approval have been met by the standards developer. An American National Standard implies a consensus of those substantially concerned with its scope and provisions. Consensus is established when, in the judgment of the ANSI Board of Standards Review, substantial agreement has been re
14、ached by directly, and materially affected interests. Substantial agreement means much more than a simple majority, but not necessarily unanimity. Consensus requires that all views and objections be considered, and that a concerted effort be made toward their resolution. The existence of an American
15、 National Standard does not in any respect preclude anyone, whether s/he has approved the standard or not, from manufacturing, marketing, purchasing, or using products, processes, or procedures not conforming to the standards. It is intended as a guide to aid the manufacturer, the consumer, and the
16、general public. The American National Standards Institute, Inc., does not develop standards and will in no circumstances give an interpretation of any American National Standard. Moreover, no person shall have the right or authority to issue an interpretation of an American National Standard in the
17、name of the American National Standards Institute, Inc. Requests for interpretations should be addressed to the secretariat or sponsor whose name appears on this title page. CAUTION NOTICE: This American National Standard may be revised or withdrawn at any time. The procedures of the American Nation
18、al Standards Institute, Inc., require that action be taken periodically to reaffirm, revise, or withdraw this standard. Purchasers of American National Standards may receive current information on all standards by calling or writing the American National Standards Institute, Inc. Published by Nation
19、al Electrical Manufacturers Association 1300 North 17thStreet, Suite 900 Rosslyn, Virginia 22209 2017 National Electrical Manufacturers Association All rights, including translation into other languages, reserved under the Universal Copyright Convention, the Berne Convention for the Protection of Li
20、terary and Artistic Works, and the International and Pan American copyright conventions. No part of this publication may be reproduced in any form, in an electronic retrieval system or otherwise, without prior written permission of the publisher. Printed in the United States of America ANSI C136.11-
21、2011 (R2016) Page ii 2017 National Electrical Manufacturers Association ANSI C136.11-2011(R2016) Page iii 2017 National Electrical Manufacturers Association CONTENTS 1 Scope 1 2 Purpose . 1 3 Normative References . 1 4 Classification 1 4.1 Voltage 1 4.2 Pulse . 1 5 Rated wattage . 1 6 Mechanical req
22、uirements . 2 6.1 Guarded 2 6.2 Lamp insertion . 2 6.3 Insertion and removal torquemogul . 2 Table 1 Insertion and removal torque for mogul sockets only* . 2 6.4 Insert and removal torquemedium 2 7 Screw shells . 2 7.1 Conformance . 2 7.2 Metal parts 2 8 Terminals and leads 2 9 Operating temperature
23、 . 3 10 Insulating material 3 Table 2 Distance insulation is to extend beyond the depressed center . contact . 3 11 Alignment . 3 12 Fatigue tests 3 ANSI C136.11-2011 (R2016) Page iv 2017 National Electrical Manufacturers Association ANSI C136.11-2011(R2016) Page 1 2017 National Electrical Manufactu
24、rers Association 1 Scope This standard covers medium and mogul screw base sockets as used in multiple fixture circuits or in luminaires designed and intended for parallel wired circuits and used in lighting roadways and other areas open to general use by the public. 2 Purpose The purpose of this sta
25、ndard is to provide interchangeability of lamps, minimum safety standards for operating personnel, and minimum performance criteria. 3 Normative References This standard incorporates, by undated reference, provisions from other publications. These normative references are cited at the appropriate pl
26、aces in the text, and the publications are listed below. For undated references, the latest edition of the publication referred to applies (including amendments). ANSI C136.2-2004 American National Standard for Roadway and Area Lighting EquipmentLuminaire Voltage Classification. ANSI C78 Series Amer
27、ican National Standards for Electric Lamps. ANSI C81.62-2009 American National Standard for Electric Lampholders. ANSI C81.63-2007 American National Standard for Gauges for Electric Lamp Bases and Lampholders. ASTM E1823-102 Standard Terminology Relating to Fatigue and Fracture Testing. Note: ANSI S
28、tandards are available from Global Engineering Documents, 15 Inverness Way East, Englewood, CO 80112-5776 Phone: 303/397-7956, Fax: 303/397-2740, E-mail: or . 4 Classification 4.1 Voltage Sockets, when mounted on their supports, shall conform to the requirements for the 250-V or 600-V classificatio
29、n given in ANSI C136.2. 4.2 Pulse Sockets, when used with high intensity discharge lamps requiring igniters, shall have a minimum pulse voltage rating of: a) 4 kVall medium sockets b) 4 kVmogul sockets when used with HPS lamps 400 W and below and all pulse start MH lamps c) 5 kVmogul sockets when us
30、ed with HPS lamps above 400 W 5 Rated wattage Medium sockets shall be rated 660 W, and mogul sockets shall be rated 1500 W. ANSI C136.11-2011 (R2016) Page 2 2017 National Electrical Manufacturers Association 6 Mechanical requirements 6.1 Guarded Parts that may be electrically energized shall be guar
31、ded to prevent accidental contact with metal parts during their installation, removal, or adjustment. 6.2 Lamp insertion Sockets shall be designed so as to allow full insertion of all lamps that meet the requirements given in the ANSI C78 Series. 6.3 Insertion and removal torquemogul Sockets shall b
32、e designed so as to maintain contact pressure and retain the lamp without loosening under normal conditions of vibration. The torque required to insert and remove mogul-base lamps shall be in accordance with Table 1. The torque test shall be performed in the sequence given on Standard Sheet 2-210-1
33、of ANSI C81.62 and with the gauges given on Standard Sheets 3-212-1 and 3-213 of ANSI C81.63. Table 1 Insertion and removal torque for mogul sockets only* Maximum insertion torque to test lamp 35 lb-in (3.95 N-m) Minimum removal torque 8 lb-in (0.90 N-m) Maximum removal torque 35 lb-in (3.95 N-m) *
34、Torque values are taken from Standard Sheet 2-210-1 of ANSI C81.62. 6.4 Insert and removal torquemedium Currently, there are no insertion and removal torque requirements for medium-base sockets in ANSI C81.62. 7 Screw shells 7.1 Conformance Socket screw shells shall be in conformance with the applic
35、able portions of ANSI C81.62 and its supplements, except that threads may be deformed, cut, or partially replaced by springs to meet the removal torque requirements of clause 6.3. The screw-shell height and center contact placement shall be such as to ensure proper electrical contact with lamp bases
36、 meeting the requirements of ANSI C81.62 and ANSI C81.63 and their supplements. 7.2 Metal parts Socket screw shells and other lamp-gripping metal parts shall be of copper or copper alloy and shall be plated with nickel or an equivalent corrosion-resistant metal. All other socket parts shall also be
37、plated with nickel or an equivalent corrosion-resistant metal. 8 Terminals and leads Socket terminals or permanently mounted leads shall be provided in accordance with the following: a) Terminals for line connections shall be suitable for both copper and aluminum conductors from 14 AWG to 6 AWG, eit
38、her solid or stranded. ANSI C136.11-2011(R2016) Page 3 2017 National Electrical Manufacturers Association b) Terminals, leads, and associated insulation for internal luminaire wiring (with a separate terminal block provided for line connections) shall be adequate for the wattage rating of the socket
39、. 9 Operating temperature The socket shall be capable of operating continuously when heated by a lamp whose operating base temperature is 210C for mogul sockets or 190C for medium sockets if electrical porcelain or other ceramic material is used. Other socket skirt materials may be used only if the
40、operating temperature in the luminaire does not exceed the thermal limits of the material. 10 Insulating material Sockets shall include a body of porcelain or other suitable insulating material that encloses the sides and bottom of the screw shell sufficiently to meet the requirements of clause 6.1
41、and that extends beyond the depressed center contact in accordance with Table 2. Table 2 Distance insulation is to extend beyond the depressed center contact Type of socket Minimum distance in inches (mm) Mogul 1-5/8 (41.3) Medium 15/16 (23.8) 11 Alignment Sockets shall be so designed that a deviati
42、on from the lamp base axis in any direction from the centerline (measured perpendicular to the socket mounting surface) will not exceed 3 degrees. The deviation shall be checked in all directions immediately after applying and slowly releasing a minimum moment load of 100 lbs.-in. (11.3 N-m) to a fu
43、lly inserted lamp-base screw-shell gauge meeting the requirements of ANSI C81.63 and its supplements. 12 Fatigue tests Sockets shall be so designed that, when used in conjunction with the maximum weight lamp (or dummy lamp) for which they are intended and when subjected to a 1 G (9.8 m-s2) vibration
44、 stress in all planes, the material used in the socket construction shall not exceed the fatigue limit stress values for those materials as determined by ASTM E1823. Fatigue tests shall be run at or below the resonant frequency of the socket and lamp (or dummy lamp), but the frequency shall not exceed 25 Hz. NATIONAL ELECTRICAL MANUFACTURERS ASSOCIATION 1300 NORTH 17TH STREET, SUITE 900 ROSSLYN. VA 22209www.NEMA.orgTO ORDER ADDITIONAL NEMA STANDARDS VISITWWW.GLOBAL.IHS.COM OR CALL 1-800-854-7179/1-303-397-79565612_0514TB
