NF C93-415-1985 Electromechanical components for electronic equipment Sensitive switches General requirements 《电子设备用机电元件 灵敏开关 一般要求》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

FORD WSK-M4D838-A-2006 POLYETHERETHERKETONE (PEEK) SELF-EXTINGUISHING (SE) MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《聚醚醚酮（PEEK）自熄灭型（SE）成型料 与标准FORD WSS-M99P1111-A一起使用》.pdf

FORD WSK-M4D839-A-2006 ACETAL (POM) COPOLYMER ELASTOMER MODIFIED MOLDING COMPOUND EXTERIOR TO BE USED WITH FORD WSS-M99P1111-A 《汽车外部用乙缩醛共聚物（POM）弹性体改性成型料 与标准FORD WSS-M99P1111-A一起使.pdf

FORD WSK-M4D840-A1-2006 ACETAL (POM) COPOLYMER MELT FLOW RATE 5 - 11 INTERIOR TO BE USED WITH FORD WSS-M99P1111-A 《汽车内部用熔体流动速率为5-11的乙缩醛共聚物（POM） 与标准FORD WSS-M99P1111-A一起使用 》.pdf

FORD WSK-M4D840-A2-2006 ACETAL (POM) COPOLYMER MELT FLOW RATE 11 - 16 INTERIOR TO BE USED WITH FORD WSS-M99P1111-A (Shown on WSK-M4D840-A1)《汽车内部用熔体流动速率为11-16的乙缩醛共聚物(POM) 与标准FORD.pdf

FORD WSK-M4D840-A3-2011 ACETAL (POM) COPOLYMER MELT FLOW RATE 29 - 35 INTERIOR TO BE USED WITH FORD WSS-M99P1111-A (Shown on FORD WSK-M4D840-A1)《内部熔态流动率为29-35的乙缩醛(POM)共聚物 与福特WSS.pdf

FORD WSK-M4D843-A2-2010 POLYPHTHALAMIDE (PPA) IMPACT MODIFIED 34% GLASS FIBER REINFORCED MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《34%玻璃纤维增强的冲击改性聚邻苯二甲酰胺(PPA)成型料 与标准F.pdf

FORD WSK-M4D844-A7-2010 POLYPHENYLENE ETHER + POLYSTYRENE BLEND (PPE+PS) HIGH HEAT MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《耐高温聚苯醚+聚苯乙烯（PPE+PS）混合物成型料 与标准FORD WSS-M9.pdf

FORD WSK-M4D844-A9-2006 POLYPHENYLENE ETHER + POLYSTYRENE BLEND (PPE +PS) IMPACT RESISTANT MOLDING COMPOUND《聚苯醚+聚苯乙烯混合物（PPE+PS）耐冲击成型料》.pdf

FORD WSK-M4D848-A-2010 POLYCARBONATE + POLYBUTYLENE THEREPHTHALATE BLEND (PC+PBT) SHEET 30% LONG GLASS FIBERS REINFORCED TO BE USED WITH FORD WSS-M99P1111-A 《30%长玻璃纤维增强的聚碳酸酯+聚对苯二.pdf