1、*USACE / NAVFAC / AFCESA / NASA UFGS-05 72 00 (May 2011)-Preparing Activity: NASA SupersedingUFGS-05 70 00 (May 2009)UNIFIED FACILITIES GUIDE SPECIFICATIONSReferences are in agreement with UMRL dated October 2011*SECTION TABLE OF CONTENTSDIVISION 05 - METALSSECTION 05 72 00DECORATIVE METAL SPECIALTI
2、ES05/11PART 1 GENERAL1.1 REFERENCES1.2 SUBMITTALS1.3 QUALIFICATIONS FOR WELDING WORK1.4 DELIVERY, STORAGE, AND HANDLING1.5 FIELD MEASUREMENTSPART 2 PRODUCTS2.1 INSTALLATION MATERIALS2.1.1 Concrete Inserts2.1.2 Masonry Anchorage Devices2.1.3 Toggle Bolts2.1.4 Standard Bolts and Nuts2.1.5 Lag Bolts2.1
3、.6 Machine Screws2.1.7 Wood Screws2.1.8 Plain Washers2.1.9 Lock Washers2.1.10 Welding Filler Metal2.2 METALS FOR FABRICATION2.2.1 Aluminum-Alloy Extrusions2.2.2 Aluminum-Alloy Sheets and Plates2.2.3 Aluminum-Alloy Castings2.2.4 Aluminum-Alloy Forgings2.2.5 Metals for Fasteners2.2.6 Shop Paint for Al
4、uminum2.3 ORNAMENTAL METAL ITEMS2.3.1 Aluminum Joint Cover Assemblies2.4 FABRICATION IN GENERAL2.4.1 Workmanship2.4.2 Holes for Other Work2.4.3 Protection of Aluminum from Dissimilar Materials2.4.4 Aluminum Finishes2.4.4.1 Preventative Maintenance and InspectionSECTION 05 72 00 Page 1Provided by IHS
5、Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-PART 3 EXECUTION3.1 GENERAL PROVISIONS3.2 ANCHORAGE DEVICES EMBEDDED IN OTHER CONSTRUCTION3.3 FASTENING TO CONSTRUCTION-IN-PLACE3.4 CUTTING AND FITTING3.5 SETTING MASONRY ANCHORAGE DEVICES3.6 WELDING PROCEDURES3.7 THR
6、EADED CONNECTIONS3.8 CLEANING3.9 INSPECTION AND ACCEPTANCE PROVISIONS3.9.1 Finished Ornamental Metal Work Requirements3.9.2 Repair of Defective Work3.10 MAINTENANCE INSTRUCTIONS- End of Section Table of Contents -SECTION 05 72 00 Page 2Provided by IHSNot for ResaleNo reproduction or networking permi
7、tted without license from IHS-,-,-*USACE / NAVFAC / AFCESA / NASA UFGS-05 72 00 (May 2011)-Preparing Activity: NASA SupersedingUFGS-05 70 00 (May 2009)UNIFIED FACILITIES GUIDE SPECIFICATIONSReferences are in agreement with UMRL dated October 2011*SECTION 05 72 00DECORATIVE METAL SPECIALTIES05/11*NOT
8、E: This guide specification covers the requirements for decorative metal products used in building construction for architectural and decorative effects.In the project drawings include a complete design indicating the character of the work to be performed by providing the following:Location and deta
9、ils of each metal item, indicating dimensions, shapes and sizes of members, connections, finishes, and the relation to other building components.Anchorage and/or fastening devices embedded in other construction.Adhere to UFC 1-300-02 Unified Facilities Guide Specifications (UFGS) Format Standard whe
10、n editing this guide specification or preparing new project specification sections. Edit this guide specification for project specific requirements by adding, deleting, or revising text. For bracketed items, choose applicable items(s) or insert appropriate information.Remove information and requirem
11、ents not required in respective project, whether or not brackets are present.Comments, suggestions and recommended changes for this guide specification are welcome and should be submitted as a Criteria Change Request (CCR).*PART 1 GENERAL1.1 REFERENCES*NOTE: This paragraph is used to list the SECTIO
12、N 05 72 00 Page 3Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-publications cited in the text of the guide specification. The publications are referred to in the text by basic designation only and listed in this paragraph by organization, designati
13、on, date, and title.Use the Reference Wizards Check Reference feature when you add a RID outside of the Sections Reference Article to automatically place the reference in the Reference Article. Also use the Reference Wizards Check Reference feature to update the issue dates.References not used in th
14、e text will automatically be deleted from this section of the project specification when you choose to reconcile references in the publish print process.*The publications listed below form a part of this specification to the extent referenced. The publications are referred to within the text by the
15、basic designation only.ALUMINUM ASSOCIATION (AA)AA ADM (2010) Aluminum Design ManualAA ASM-35 (2000) Specifications for Aluminum Sheet Metal Work in Building Construction, Construction Manual Series Section 5AA DAF45 (2003; Reaffirmed 2009) Designation System for Aluminum FinishesAA PK-1 (2009) Pink
16、 Sheets: Designations and Chemical Composition Limits for Aluminum Alloys in the Form of Castings R 2007) Specification for Aluminum and Aluminum-Alloy Electrodes for Shielded Metal Arc WeldingAWS D1.2/D1.2M (2008) Structural Welding Code - AluminumASME INTERNATIONAL (ASME)ASME B18.13 (1996; Addenda
17、 A 1998; R 2008) Screw and Washer Assemblies - Sems (Inch Series)ASME B18.13.1M (1998; R 2008) Screw and Washer Assemblies-SEMS (Metric Series)ASME B18.2.1 (2010) Square and Hex Bolts and Screws (Inch Series)ASME B18.2.2 (2010) Standard for Square and Hex NutsSECTION 05 72 00 Page 4Provided by IHSNo
18、t for ResaleNo reproduction or networking permitted without license from IHS-,-,-ASME B18.2.3.8M (1981; R 2005) Metric Hex Lag ScrewsASME B18.2.4.1M (2002; R 2007) Metric Hex Nuts, Style 1ASME B18.21.1 (2009) Washers: Helical Spring-Lock, Tooth Lock, and Plain Washers (Inch Series)ASME B18.21.2M (19
19、99; R 2005) Lock Washers (Metric Series)ASME B18.22M (1981; R 2010) Metric Plain WashersASME B18.24 (2004; Addenda A 2006) Part Identifying Number (PIN) Code System Standard for B18 Fastener ProductsASME B18.3.3M (1986; R 2008) Hexagon Socket Head Shoulder Screws (Metric Series)ASME B18.6.1 (1981; R
20、 2008) Wood Screws (Inch Series)ASME B18.6.3 (2003; R 2008) Machine Screws and Machine Screw NutsASME B18.6.5M (2000; R 2010) Standard Specification for Metric Thread-Forming and Thread-Cutting Tapping ScrewsASME B18.6.7M (1999; R 2010) Metric Machine ScrewsASTM INTERNATIONAL (ASTM)ASTM A123/A123M (
21、2009) Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel ProductsASTM A153/A153M (2009) Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel HardwareASTM A27/A27M (2010) Standard Specification for Steel Castings, Carbon, for General ApplicationASTM A283/A2
22、83M (2003; R 2007) Standard Specification for Low and Intermediate Tensile Strength Carbon Steel PlatesASTM A47/A47M (1999; R 2009) Standard Specification for Ferritic Malleable Iron CastingsASTM B209 (2010) Standard Specification for Aluminum and Aluminum-Alloy Sheet and PlateASTM B209M (2010) Stan
23、dard Specification for Aluminum and Aluminum-Alloy Sheet and Plate (Metric)ASTM B211 (2003) Standard Specification for Aluminum and Aluminum-Alloy Bar, Rod, and WireASTM B211M (2003) Standard Specification for Aluminum SECTION 05 72 00 Page 5Provided by IHSNot for ResaleNo reproduction or networking
24、 permitted without license from IHS-,-,-and Aluminum-Alloy Bar, Rod, and Wire (Metric)ASTM B221 (2008) Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and TubesASTM B221M (2007) Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wi
25、re, Profiles, and Tubes (Metric)ASTM B247 (2009) Standard Specification for Aluminum and Aluminum-Alloy Die Forgings, Hand Forgings, and Rolled Ring ForgingsASTM B247M (2009) Standard Specification for Aluminum and Aluminum-Alloy Die Forgings, Hand Forgings, and Rolled Ring Forgings (Metric)ASTM B26
26、/B26M (2009) Standard Specification for Aluminum-Alloy Sand CastingsASTM B316/B316M (2010) Standard Specification for Aluminum and Aluminum-Alloy Rivet and Cold-Heading Wire and RodsASTM C514 (2004; R 2009e1) Standard Specification for Nails for the Application of Gypsum BoardASTM C636/C636M (2008)
27、Standard Practice for Installation of Metal Ceiling Suspension Systems for Acoustical Tile and Lay-In PanelsASTM D 1730 (2009) Standard Practices for Preparation of Aluminum and Aluminum-Alloy Surfaces for PaintingASTM D 1752 (2004a; R 2008) Standard Specification for Preformed Sponge Rubber Cork an
28、d Recycled PVC ExpansionASTM G 71 (1981; R 2009) Standard Guide for Conducting and Evaluating Galvanic Corrosion Tests in ElectrolytesASTM G 82 (1998; R 2009) Standard Guide for Development and Use of a Galvanic Series for Predicting Galvanic Corrosion PerformanceTHE SOCIETY FOR PROTECTIVE COATINGS
29、(SSPC)CS 23.00/AWS C2.23M/NACE #12 (2003) Specification for the Application of Thermal Spray Coatings (Metallizing) of Aluminum, Zinc, and Their Alloys and Composites for the Corrosion Protection of SteelSECTION 05 72 00 Page 6Provided by IHSNot for ResaleNo reproduction or networking permitted with
30、out license from IHS-,-,-SSPC PA 1 (2000; E 2004) Shop, Field, and Maintenance Painting of SteelSSPC PS 11.01 (1982; E 2004) Black (or Dark Red) Coal Tar Epoxy Polyamide Painting SystemU.S. GENERAL SERVICES ADMINISTRATION (GSA)CID A-A-344 (Rev B; Notice 1) Lacquer (Clear Gloss)1.2 SUBMITTALS*NOTE: R
31、eview Submittal Description (SD) definitions in Section 01 33 00 SUBMITTAL PROCEDURES and edit the following list to reflect only the submittals required for the project. Submittals should be kept to the minimum required for adequate quality control.A “G” following a submittal item indicates that th
32、e submittal requires Government approval. Some submittals are already marked with a “G”. Only delete an existing “G” if the submittal item is not complex and can be reviewed through the Contractors Quality Control system. Only add a “G” if the submittal is sufficiently important or complex in contex
33、t of the project.For submittals requiring Government approval on Army projects, a code of up to three characters within the submittal tags may be used following the “G“ designation to indicate the approving authority. Codes for Army projects using the Resident Management System (RMS) are: “AE“ for A
34、rchitect-Engineer; “DO“ for District Office (Engineering Division or other organization in the District Office); “AO“ for Area Office; “RO“ for Resident Office; and “PO“ for Project Office. Codes following the “G“ typically are not used for Navy, Air Force, and NASA projects.Choose the first bracket
35、ed item for Navy, Air Force and NASA projects, or choose the second bracketed item for Army projects.*Government approval is required for submittals with a “G“ designation; submittals not having a “G“ designation are for Contractor Quality Control approval.for information only. When used, a designat
36、ion following the “G“ designation identifies the office that will review the submittal for the Government. Submit the following in accordance with Section 01 33 00 SUBMITTAL PROCEDURES:SD-01 Preconstruction SubmittalsSubmit survey data showing Existing Conditions prior to work in accordance with par
37、agraph entitled, “Field Measurements,“ of this section.SECTION 05 72 00 Page 7Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SD-02 Shop DrawingsSubmit fabrication drawings for Ornamental Metal Items in accordance with the paragraph entitled, “Fabric
38、ation In General,“ of this section.Submit Installation Drawings for the following items in accordance with paragraph entitled, “Fabrication In General,“ of this section.Ornamental Metal ItemsShop and Field ConnectionsConstruction DetailsSD-03 Product DataSubmit manufacturers catalog data for the fol
39、lowing items listing all ornamental metal accessories including casting, forgings, fasteners and anchorage devices.Installation MaterialsMetals for FabricationOrnamental Metal ItemsSD-04 SamplesSubmit Manufacturers Standard Color Charts for the following items and secure Contracting Officers approva
40、l prior to work commencement.Shop PaintFinish PaintSamples for Aluminum Finishes, one for each type, complying with paragraph entitled, “Aluminum Finishes,“ of this section.Submit samples for each type of Anchorage Devices and Fasteners in accordance with paragraph entitled, “Installation Materials,
41、“ of this section.Submit samples for each type of Architectural Metal Items in accordance with paragraph entitled, “Metals for Fabrications,“ of this section.Submit samples for aluminum finishes, two of each type, in accordance with paragraph entitled, “Ornamental Metal Items,“ of this section.Provi
42、de samples of standard size as used in construction. After approval, full-sized samples may be used in construction, provided each sample is clearly identified and its location recorded.SD-06 Test ReportsSubmit Test reports for Welding Tests complying with SECTION 05 72 00 Page 8Provided by IHSNot f
43、or ResaleNo reproduction or networking permitted without license from IHS-,-,-AWS D1.2/D1.2M, “Qualifications of Procedures and Personnel.“SD-07 CertificatesSubmit Welding Procedures complying with AWS D1.2/D1.2M, “Structural Welding Code - Aluminum.“Submit Certificates for Ornamental Metal Items in
44、 accordance with the paragraphs entitled, “Metals For Fabrication“ and “Ornamental Metal Items.“ Certificates of Welder Qualifications are to comply with the paragraph entitled, “Qualifications for Welding Work,“ of this section.SD-08 Manufacturers InstructionsSubmit Preventative Maintenance and Ins
45、pection instructions for the following items in accordance with paragraph entitled, “Aluminum Finishes,“ of this section.Cleaning Materials and Maintenance InstructionsApplication Methods1.3 QUALIFICATIONS FOR WELDING WORK*NOTE: If Section 05 14 00.13 WELDING STRUCTURAL ALUMINUM FRAMING is not included in the project specification, applicable requirements thereof should be inserted and the following paragraph deleted.*Section 05 14 00.13 WELDING STRUCTURAL ALUMINUM FRAMING applies to work specified in this section.Submit Welding Pr
