SAE AMS 3892 9B-1992 Tow Carbon Fiber for Structural Composites 500 (3447) Tensile Strength 32 (221) Tensile Modulus《500(3447)抗拉强度、32(221)抗拉模数的结构复合材料用碳纤维束》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

GOST IEC 61184-2011 Bayonet lampholders《卡口灯座》.pdf

GOST IEC 61188-1-1-2013 Printed boards and printed board assemblies Design and use Part 1-1 Generic requirements Flatness considerations for electronic assemblies《印制板和印制板组件 设计和使用 第.pdf

GOST IEC 61188-1-2-2013 Printed boards and printed board assemblies Design and use Part 1-2 Generic requirements Controlled impedance《印制板和印制板组件 设计和使用 第1-2部分 通用要求 控制阻抗》.pdf

GOST IEC 61188-5-2-2013 Printed boards and printed board assemblies Design and use Part 5-2 Attachment (land joint) considerations Discrete components《印制板和印制板组件 设计和使用 第5-2部分 连接 (焊盘.pdf

GOST IEC 61188-5-3-2013 Printed boards and printed board assemblies Design and use Part 5-3 Attachment (land joint) considerations Components with gull-wing leads on two sides《印制板和.pdf

GOST IEC 61188-5-4-2013 Printed boards and printed board assemblies Design and use Part 5-4 Attachment (land joint) considerations Components with J leads on two sides《印制板和印制板组件 设计.pdf

GOST IEC 61188-5-5-2013 Printed boards and printed board assemblies Design and use Part 5-5 Attachment (land joint) considerations Components with gull-wing leads on four sides《印制板.pdf

GOST IEC 61188-5-6-2013 Printed boards and printed board assemblies Design and use Part 5-6 Attachment (land joint) considerations Chip carriers with J-leads on four sides《印制板和印制板组.pdf

GOST IEC 61188-5-8-2013 Printed boards and printed board assemblies Design and use Part 5-8 Attachment (land joint) considerations Area array components (BGA FBGA CGA LGA)《印制板和印制板组.pdf