1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there
2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2013 SAE International All rights reserved. No part of this p
3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497
4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS5044J AEROSPACE MATERIAL SPECIFICATION AMS5044 REV. J Issued 1942-12 Revised 2
5、005-09 Reaffirmed 2013-10 Superseding AMS5044H Steel, Sheet and Strip 0.15 Carbon, Maximum Half Hard Temper (Composition similar to UNS G10100) RATIONALE AMS5044J has been reaffirmed to comply with the SAE five-year review policy. 1. SCOPE: 1.1 Form: This specification covers a carbon steel in the f
6、orm of sheet and strip. 1.2 Application: These products have been used typically for stamped parts and for parts requiring bending only normal to the direction of rolling, but usage is not limited to such applications. 2. APPLICABLE DOCUMENTS: The issue of the following documents in effect on the da
7、te of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the
8、last published issue of that document shall apply. 2.1 SAE Publications: Available from SAE, 400 Commonwealth Drive, Warrendale, PA 15096-0001 or www.sae.org. AMS 2232 Tolerances, Carbon Steel Sheet, Strip, and Plate AMS 2259 Chemical Check Analysis Limits, Wrought Low-Alloy and Carbon Steels AMS 23
9、70 Quality Assurance Sampling and Testing, Carbon and Low-Alloy Steel Wrought Products and Forging Stock AMS 2807 Identification, Carbon and Low-Alloy Steels, Corrosion and Heat Resistant Steels and Alloys, Sheet, Strip, Plate, and Aircraft Tubing SAE INTERNATIONAL AMS5044J Page 2 of 4 2.2 ASTM Publ
10、ications: Available from ASTM, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959 or www.astm.org. ASTM E 350 Chemical Analysis of Carbon Steel, Low-Alloy Steel, Silicon Electrical Steel, Ingot Iron, and Wrought Iron ASTM A 370 Mechanical Testing of Steel Products 3. TECHNICAL RE
11、QUIREMENTS: 3.1 Composition: Shall conform to the percentages by weight shown in Table 1, determined by wet chemical methods in accordance with ASTM E 350, by spectrochemical methods, or by other analytical methods acceptable to purchaser. TABLE 1 - Composition Element min max Carbon - 0.15 Manganes
12、e 0.30 0.60 Phosphorus - 0.035Sulfur - 0.0403.1.1 Check Analysis: Composition variations shall meet the applicable requirements of AMS 2259. 3.2 Condition: Product shall be cold rolled. 3.3 Properties: The product shall conform to the following requirements: hardness and bend tests shall be performe
13、d in accordance with ASTM A 370. 3.3.1 Hardness: Shall be as shown in Table 2, or equivalent (See 8.2). TABLE 2 - Hardness Nominal Thickness Inches Nominal Thickness Millimeters Hardness 0.009 to 0.017, incl 0.23 to 0.43, incl 83.5 to 89 HR15TOver 0.017 to 0.032, incl Over 0.43 to 0.81, incl 63.5 to
14、 74 HR30TOver 0.032 to 0.054, incl Over 0.81 to 1.37, incl 96 to 105 HRF Over 0.054 Over 1.37 70 to 85 HRB SAE INTERNATIONAL AMS5044J Page 3 of 4 3.3.2 Bending: The product shall withstand, without cracking, bending at room temperature through an angle of 90 degrees around a diameter equal to twice
15、the nominal thickness of the product, with axis of bend perpendicular to the direction of rolling. 3.4 Quality: The product, as received by purchaser, shall be uniform in quality and condition, sound, and free from foreign materials and from imperfections detrimental to usage of the product. 3.5 Tol
16、erances: Shall conform to all applicable requirements of AMS 2232. 4. QUALITY ASSURANCE PROVISIONS: 4.1 Responsibility for Inspection: The vendor of the product shall supply all samples for vendors tests and shall be responsible for the performance of all required tests. Purchaser reserves the right
17、 to sample and to perform any confirmatory testing deemed necessary to ensure that the product conforms to specified requirements. 4.2 Classification of Tests: Tests for all technical requirements are acceptance tests and shall be performed on each heat or lot as applicable. 4.3 Sampling and Testing
18、: Shall be in accordance with AMS 2370. 4.4 Reports: The vendor of the product shall furnish with each shipment a report showing the results of tests for composition of each heat and hardness and bending properties of each lot, and stating that the product conforms to the other technical requirement
19、s. This report shall include the purchase order number, heat and lot numbers, AMS 5044J, size, and quantity. 4.5 Resampling and Retesting: Shall be in accordance with AMS 2370. 5. PREPARATION FOR DELIVERY: 5.1 Identification: Shall be in accordance with ASTM 2807. SAE INTERNATIONAL AMS5044J Page 4 o
20、f 4 5.2 Protective Treatment: The product shall be protected from corrosion prior to shipment. 5.3 Packaging: The product shall be prepared for shipment in accordance with commercial practice and in compliance with applicable rules and regulations pertaining to the handling, packaging, and transport
21、ation of the product to ensure carrier acceptance and safe delivery. 6. ACKNOWLEDGMENT: A vendor shall mention this specification number and its revision letter in all quotations and when acknowledging purchase orders. 7. REJECTIONS: Product not conforming to this specification, or to modifications
22、authorized by purchaser, will be subject to rejection. 8. NOTES: 8.1 A change bar (|) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of a specification. An (R) symbol to the left o
23、f the document title indicates a complete revision of the specification, including technical revision. Change bars and (R) are not used in original publications, nor in specifications that contain editorial changes only. 8.2 Hardness conversion tables for metals are presented in ASTM E 140. 8.3 Term
24、s used in AMS are clarified in ARP1917. 8.4 Dimensions and properties in inch/pound units and Fahrenheit temperatures are primary; dimensions and properties in SI units and Celsius temperatures are shown as the approximate equivalents of the primary units and are presented only for information. 8.5 Purchase documents should specify not less than the following: AMS 5044J Form and size of product desired Quantity of product desired. 8.6 Key Words: Steel, sheet, strip, 0.15 Carbon, half hard, temper, UNS G10100 PREPARED UNDER THE JURISDICTION OF AMS COMMITTEE “E“
