1、AEROSPACE MATERIAL SPECIFICATION AMS5717 REV. H Issued 1964-01 Revised 2003-07 Reaffirmed 2014-10 Superseding AMS5717G Nickel Alloy, Corrosion and Heat-Resistant, Bars, Forgings, and Rings45.5Ni - 25.5Cr - 3.2Co - 3.2Mo - 3.2W - 18.5Fe Solution Heat Treated (Composition similar to UNS N06333) RATION
2、ALE AMS5717H has been reaffirmed to comply with the SAE five year review policy. _ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and su
3、itability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and sug
4、gestions. Copyright 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLAC
5、E A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/
6、AMS5717H 1. SCOPE:1.1 Form: This specification covers a corrosion and heat-resistant nickel alloy in the form of bars, forgings, flash welded rings, and stock for forging or flash welded rings.1.2 Application: These products have been used typically for parts requiring heat and oxidation resistance
7、up to 2150 F (1177 C), particularly where such parts may require welding during fabrication, but usage is not limited to such applications.2. APPLICABLE DOCUMENTS: The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specif
8、ied herein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been canceled and no superseding document has been specified, the last published issue of that document shall apply.SAE INTERNATIONAL AMS5717H Page
9、 2 of 6 2.1 SAE Publications: Available from SAE, 400 Commonwealth Drive, Warrendale, PA 15096-0001 or www.sae.org.AMS 2241 Tolerances, Corrosion and Heat Resistant Steel, Iron Alloy, Titanium, and Titanium Alloy Bars and WireAMS 2248 Chemical Check Analysis Limits, Corrosion and Heat-Resistant Stee
10、ls and Alloys, Maraging and Other Highly-Alloyed Steels, and Iron AlloysAMS 2371 Quality Assurance Sampling and Testing, Corrosion and Heat-Resistant Steels and Alloys, Wrought Products and Forging StockAMS 2374 Quality Assurance Sampling and Testing, Corrosion and Heat-Resistant Steel and Alloy For
11、gingsAMS 2806 Identification, Bars, Wire, Mechanical Tubing, and Extrusions, Carbon and Alloy Steels and Corrosion and Heat-Resistant Steels and AlloysAMS 2808 Identification, ForgingsAMS 7490 Rings, Flash Welded, Corrosion and Heat-Resistant Austenitic Steels, and Austenitic-Type Alloys or Precipit
12、ation-Hardenable-Alloys2.2 ASTM Publications: Available from ASTM, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959 or www.astm.org.ASTM E 8 Tension Testing of Metallic MaterialsASTM E 8M Tension Testing of Metallic Materials (Metric)ASTM E 18 Rockwell Hardness and Rockwell Superficial Hardne
13、ss of Metallic MaterialsASTM E 354 Chemical Analysis of High-Temperature, Electrical, Magnetic, and Other Similar Iron, Nickel, and Cobalt Alloys3. TECHNICAL REQUIREMENTS: 3.1 Composition: Shall conform to the percentages by weight shown in Table 1, determined by wet chemical methods in accordance w
14、ith ASTM E 354, by spectrochemical methods, or by other analytical methods acceptable to purchaser.SAE INTERNATIONAL AMS5717H Page 3 of 6 3.1.1 Check Analysis: Composition variations shall meet the applicable requirements of AMS 2248.3.2 Condition: The product shall be supplied in the following cond
15、ition:3.2.1 Bars, Forgings, and Flash Welded Rings: Solution heat treated.3.2.1.1 Bars shall be hot finished, except that bars under 0.250 inch (6.35 mm) in nominal diameter or distance between parallel sides may be cold finished.3.2.1.2 Flash welded rings shall not be supplied unless specified or p
16、ermitted on purchasers part drawing. When supplied, rings shall be manufactured in accordance with AMS 7490.3.2.2 Stock for Forging or Flash Welded Rings: As ordered by the forging or flash welded ring manufacturer.3.3 Heat Treatment: No specific heat treating instructions are specified, but bars, f
17、orgings, and flash welded rings shall be solution heat treated to produce the properties specified in 3.4.1.1 and 3.4.1.2. Recommended solution heat treatment is presented in 3.3.1.TABLE 1 - CompositionElement min maxCarbon - 0.08Manganese - 2.00Silicon 0.75 1.50Phosphorus - 0.030Sulfur - 0.030Chrom
18、ium 24.00 27.00Nickel 44.00 47.00Cobalt 2.50 4.00Molybdenum 2.50 4.00Tungsten 2.50 4.00Copper - 0.50Tin - 0.025Lead - 0.025Iron remainderSAE INTERNATIONAL AMS5717H Page 4 of 6 3.3.1 Bars, forgings, and flash welded rings should be solution heat treated by heating to a temperature not lower than 1950
19、 F (1066 C), holding at the selected temperature within 25 F (14 C) for a time commensurate with cross-sectional thickness, and cooling at a rate equivalent to an air cool or faster.3.4 Properties: The product shall conform to the following requirements:3.4.1 Bars, Forgings, and Flash Welded Rings:
20、3.4.1.1 Tensile Properties: Shall be as shown in Table 2, determined in accordance with ASTM E 8 or ASTM E 8M:3.4.1.2 Hardness: Shall be not higher than 95 HRB, or equivalent (See 8.2), determined in accordance with ASTM E 18.3.4.2 Stock for Forging or Flash Welded Rings: As agreed upon by purchaser
21、 and vendor.3.5 Quality: The product, as received by purchaser, shall be uniform in quality and condition, sound, and free from foreign materials and from imperfections detrimental to usage of the product.3.5.1 Grain flow of die forgings, except in areas which contain flash-line end grain, shall fol
22、low the general contour of the forgings showing no evidence of reentrant grain flow.3.6 Tolerances: Bars shall conform to all applicable requirements of AMS 2241.4. QUALITY ASSURANCE PROVISIONS: 4.1 Responsibility for Inspection: The vendor of the product shall supply all samples for vendors tests a
23、nd shall be responsible for the performance of all required tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that the product conforms to specified requirements.TABLE 2 - Tensile PropertiesProperty ValueTensile Strength, maximum 120 ksi
24、 (827 MPa)Yield Strength at 0.2% Offset, minimum 35.0 ksi (241 MPa)Elongation in 4D, minimum 30%SAE INTERNATIONAL AMS5717H Page 5 of 6 4.2 Classification of Tests: 4.2.1 Acceptance Tests: Composition (3.1), tensile properties (3.4.1.1), hardness (3.4.1.2), and tolerances (3.6) are acceptance tests a
25、nd shall be performed on each heat or lot as applicable.4.2.2 Periodic Tests: Grain flow of die forgings (3.5.1) is a periodic test and shall be performed at a frequency selected by the vendor unless frequency of testing is specified by purchaser.4.3 Sampling and Testing: Shall be as follows:4.3.1 B
26、ars, Flash Welded Rings, and Stock for Forging or Flash Welded Rings: In accordance withAMS 2371.4.3.2 Forgings: In accordance with AMS 2374.4.4 Reports: The vendor of the product shall furnish with each shipment a report showing the results of tests for composition of each heat and for tensile prop
27、erties and hardness requirements of each lot, and stating that the product conforms to the other technical requirements. This report shall include the purchase order number, heat and lot numbers, AMS 5717H, specific heat treating cycles used to obtain reported properties, size, and quantity. If forg
28、ings are supplied, the part number and the size and melt source of stock used to make the forgings shall also be included.4.5 Resampling and Retesting: Shall be as follows:4.5.1 Bars, Flash Welded Rings, and Stock for Forging or Flash Welded Rings: In accordance withAMS 2371.4.5.2 Forgings: In accor
29、dance with AMS 2374.5. PREPARATION FOR DELIVERY: 5.1 Sizes: Except when exact lengths or multiples of exact lengths are ordered, straight bars will be acceptable in mill lengths of 6 to 24 feet (1.8 to 7.3 m) but not more than 25% of any shipment shall be supplied in lengths of 6 to 9 feet (1.8 to 2
30、.7 m) except that for bars weighing over 25 pounds per foot (37 kg/m), short lengths down to 2 feet (610 mm) may be supplied.5.2 Identification: Shall be as follows:SAE INTERNATIONAL AMS5717H Page 6 of 6 5.2.1 Bars: In accordance with AMS 2806.5.2.2 Forgings: In accordance with AMS 2808.5.2.3 Flash
31、Welded Rings and Stock for Forging, or Flash Welded Rings: As agreed upon by purchaser and vendor.5.3 Packaging: The product shall be prepared for shipment in accordance with commercial practice and in compliance with applicable rules and regulations pertaining to the handling, packaging, and transp
32、ortation of the product to ensure carrier acceptance and safe delivery.6. ACKNOWLEDGMENT: A vendor shall mention this specification number and its revision letter in all quotations and when acknowledging purchase orders.7. REJECTIONS: Product not conforming to this specification, or to modifications
33、 authorized by purchaser, will be subject to rejection.8. NOTES:8.1 A change bar (|) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this specification. An (R) symbol to the left
34、 of the document title indicates a complete revision of the specification, including technical revisions. Change bars and (R) are not used in original publications, nor in specifications that contain editorial changes only.8.2 Hardness conversion tables for metals are presented in ASTM E 140.8.3 Ter
35、ms used in AMS are clarified in ARP1917.8.4 Dimensions and properties in inch/pound units and the Fahrenheit temperatures are primary; dimensions and properties in SI units and the Celsius temperatures are shown as the approximate equivalents of the primary units and are presented only for information.8.5 Procurement documents should specify not less than the following: AMS 5717HForm and size or part number of product desiredQuantity of product desired.PREPARED UNDER THE JURISDICTION OF AMS COMMITTEE “F”
