1、AEROSPACE STANDARD FITTING, TEE, STANDARD AND REDUCER, BULKHEAD ON RUN, INTERNAL PORT ON RUN, FLARED AS1032Copyright 2010 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechan
2、ical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1962-08REVISED 2
3、010-05THIRD ANGLE PROJECTION CUSTODIAN: G-3/G-3B REV.FFEDERAL SUPPLY CLASS 4730 AS1032SHEET 1 OF 7REV. FPROCUREMENT SPECIFICATION: /4/ AS4875/1SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report
4、 is entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay bereaffirmed, revised, orcancelled. SAE invites yo
5、urwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS1032FRATIONALE OPERATING PRESSURES FOR ALUMINUM FITTINGS CLARIFIED. NADCAP-QML REQUIREMENT HAS BEEN ADDED. MATERIAL AND FINISH SPECIFICATION NUMB
6、ERS HAVE BEEN UPDATED. OTHER CLARIFICATIONS AND UPDATES.FIGURE 1 - FITTING, TEE, BULKHEAD END FOR OPTIONAL USE IN PORT PORT #2 SHOWN AS NON-REDUCER INACTIVE IN PART /25/ FIGURE 2 - FITTING, TEE, BULKHEAD END FOR OPTIONAL USE IN PORT PORT #2 SHOWN AS REDUCER SAME AS FIGURE 1 EXCEPT AS SHOWN AEROSPACE
7、 STANDARD AS1032SHEET 2 OF 7REV. FFITTING, TEE, STANDARD AND REDUCER, BULKHEAD ON RUN, INTERNAL PORT ON RUN, FLARED FIGURE 3 - FITTING, TEE, BULKHEAD END NOT FOR USE IN PORT PORT #2 SHOWN AS NON-REDUCER SAME AS FIGURE 1 EXCEPT AS SHOWN /23/ FIGURE 4 - FITTING, TEE, BULKHEAD END NOT FOR USE IN PORT P
8、ORT #2 SHOWN AS REDUCER SAME AS FIGURE 1 EXCEPT AS SHOWN /23/ TABLE 1 - DIMENSIONS AND WEIGHTS /16/ BASIC NO. AS1032/13/ /23/ SIZE CODE E/12/F/12/ V W Z/14/LB/EAAPPROX REF ALUMLB/EAAPPROX REF STEELLB/EAAPPROX REF TI02 .648 - .485- .502 .090 .562 .0313 .0898 .0496 03 .711 - .547- .565 .100 .625 .0410
9、 .1179 .06498 04 .773 .375 .735- .753 .110 - .0837 .2403 .1323 05 .773 .375 .735- .753 .120 - .0806 .2313 .1278 06 .836 .375 .860- .878 .120 - .1206 .3474 .1917 08 1.023 .469 1.047-1.065 .150 - .2160 .5553 .306 10 1.180 .625 1.047-1.065 .170 1.125 .1989 .5724 .316 12 1.367 .688 1.292-1.317 .185 1.37
10、5 .3285 .945 .521 16 1.555 .719 1.605-1.630 .205 1.625 .4743 1.359 .752 20 1.742 .781 1.855-1.880 .240 1.938 .6831 1.962 1.08 AEROSPACE STANDARD AS1032SHEET 3 OF 7REV. FFITTING, TEE, STANDARD AND REDUCER, BULKHEAD ON RUN, INTERNAL PORT ON RUN, FLARED TABLE 2 - LEG LENGTH B FORGING SIZE/13/TUBE SIZE
11、OF PORT #1 02TUBE SIZE OF PORT #1 03TUBE SIZE OF PORT #1 04TUBE SIZE OF PORT #1 05TUBE SIZE OF PORT #1 06TUBE SIZE OF PORT #1 08TUBE SIZE OF PORT #1 10TUBE SIZE OF PORT #1 12TUBE SIZE OF PORT #1 16TUBE SIZE OF PORT #1 2002 1.491 - - - - - - - - - 03 1.523 1.523 - - - - - - - - 04 1.679 1.679 1.773 -
12、 - - - - - - 05 1.679 1.679 1.773 1.773 - - - - - - 06 1.851 1.851 1.945 1.945 2.023 - - - - - 08 1.851 1.851 1.945 1.945 2.023 2.179 - - - - 10 1.929 1.929 2.023 2.023 2.101 2.257 2.398 - - - 12 2.008 2.008 2.102 2.102 2.180 2.336 2.477 2.648 - - 16 2.227 2.227 2.321 2.321 2.399 2.555 2.696 2.867 2
13、.867 - 20 2.367 2.367 2.461 2.461 2.539 2.695 2.836 3.007 3.007 3.054 TABLE 3 - LEG LENGTH D FORGING SIZE/13/TUBE SIZE OF PORT #3 02TUBE SIZE OF PORT #3 03TUBE SIZE OF PORT #3 04TUBE SIZE OF PORT #3 05TUBE SIZE OF PORT #3 06TUBE SIZE OF PORT #3 08TUBE SIZE OF PORT #3 10TUBE SIZE OF PORT #3 12TUBE SI
14、ZE OF PORT #3 16TUBE SIZE OF PORT #3 2002 .929 - - - - - - - - - 03 .961 .992 - - - - - - - - 04 1.109 1.140 1.211 - - - - - - - 05 1.109 1.140 1.211 1.211 - - - - - - 06 1.165 1.196 1.267 1.267 1.273 - - - - - 08 1.232 1.283 1.354 1.354 1.360 1.461 - - - - 10 1.338 1.369 1.440 1.440 1.446 1.547 1.6
15、48 - - - 12 1.420 1.451 1.522 1.522 1.528 1.629 1.730 1.836 - - 16 1.623 1.654 1.725 1.725 1.731 1.832 1.933 2.039 2.086 - 20 1.763 1.794 1.865 1.865 1.871 1.972 2.073 2.179 2.226 2.273 TABLE 4 - G /15/ FORGING SIZE/13/TUBE SIZE OF PORT #2 02TUBE SIZE OF PORT #2 03TUBE SIZE OF PORT #2 04TUBE SIZE OF
16、 PORT #2 05TUBE SIZE OF PORT #2 06TUBE SIZE OF PORT #2 08TUBE SIZE OF PORT #2 10TUBE SIZE OF PORT #2 12TUBE SIZE OF PORT #2 1603 - - - - - - - - - 04 .594 .656 - - - - - - - 05 .594 .656 - - - - - - - 06 .594 .656 .719 .781 - - - - - 08 .594 .656 .719 .781 .844 - - - - 10 .594 .656 .719 .781 .844 -
17、- - - 12 .594 .656 .719 .781 .844 1.062 - - - 16 .594 .656 .719 .781 .844 1.062 1.188 1.438 - 20 .594 .656 .719 .781 .844 1.062 1.188 1.438 1.688 AEROSPACE STANDARD AS1032SHEET 4 OF 7REV. FFITTING, TEE, STANDARD AND REDUCER, BULKHEAD ON RUN, INTERNAL PORT ON RUN, FLARED TABLE 5 - TUBE SIZE AND CORRE
18、SPONDING THREAD PORT SIZE(NOMINAL TUBE SIZE)T THREAD PER AS8879 CLASS 3A 02 .125 .3125-24 UNJF 03 .188 .3750-24 UNJF 04 .250 .4375-20 UNJF 05 .312 .5000-20 UNJF 06 .375 .5625-18 UNJF 08 .500 .7500-16 UNJF 10 .625 .8750-14 UNJF 12 .750 1.0625-12 UNJ 16 1.000 1.3125-12 UNJ20 1.250 1.6250-12 UNJ NOTICE
19、: THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. NOTES: /1/ MATERIAL: a. DASH AS CODE LETTER - TYPE 4130 STEEL FORGING OR BAR PER AMS6370 OR AMS-S-6758, OR TYPE 4140 STEEL BAR PER AMS6349 OR AMS6382
20、. b. CODE LETTER D - TYPE 2014-T6 ALUMINUM ALLOY FORGING PER AMS4133 OR AMS-QQ-A-367; OR 2024-T6 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/6; OR 2024-T851 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/6. /25/ c. CODE LETTER J - TYPE 304 CORROSION RESISTANT STEEL FORGING OR BAR PER AMS5639. d. CODE LETTER K - TYPE 3
21、16 CORROSION RESISTANT STEEL FORGING OR BAR PER AMS5648. e. CODE LETTER R - TYPE 321 CORROSION RESISTANT STEEL FORGING OR BAR PER AMS5645. f. CODE LETTER S - TYPE 347 CORROSION RESISTANT STEEL FORGING OR BAR PER AMS5646. /25/ g. CODE LETTER T - 6AL-4V TITANIUM ALLOY FORGING OR BAR PER AMS4928. /24/
22、h. CODE LETTER W - 7075-T73 ALUMINUM ALLOY FORGING PER AMS4141 OR AMS-QQ-A-367; OR 7075-T7351 ALUMINUM ALLOY BAR PER AMS4124; OR 7075-T73 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/9. 2. HEAT TREATMENT: a. DASH AS CODE LETTER - HARDNESS SHALL BE 92 HRB TO 40 HRC PER PROCUREMENT SPECIFICATION. b. OTHER MATE
23、RIAL CODE LETTERS - NONE. 3. FINISH: a. DASH AS CODE LETTER - CADMIUM PLATE PER AMS-QQ-P-416, TYPE II, CLASS 2, DYE BLACK. b. MATERIAL CODE LETTER D: 1. ANODIZE PER AMS2472 OR MIL-A-8625, TYPE II, CLASS 2, DYE BLUE, DUPLEX SEAL PER PROCUREMENT SPECIFICATION. AEROSPACE STANDARD AS1032SHEET 5 OF 7REV.
24、 FFITTING, TEE, STANDARD AND REDUCER, BULKHEAD ON RUN, INTERNAL PORT ON RUN, FLARED 2. D CODE PARTS TO BE COATED WITH HIGH PURITY ALUMINUM ONLY WILL HAVE THE FINISH CODE LETTER “V” PLACED AFTER THE SIZE CODE IN THE PART NUMBER. THE FINISH WILL BE: COAT WITH HIGH PURITY ALUMINUM PER MIL-DTL-83488, CL
25、ASS 3, TYPE II, WITH MAXIMUM COATING THICKNESS OF .0005. GLASS BEAD PEEN PRESSURE SHALL BE 25 psi MAXIMUM. /23/ SEE PROCUREMENT SPECIFICATION FOR ADDITIONAL REQUIREMENTS. c. MATERIAL CODE LETTER J - PASSIVATE PER AMS 2700, TYPE 6 OR 7. d. MATERIAL CODE LETTER K - PASSIVATE PER AMS 2700, TYPE 6 OR 7.
26、 e. MATERIAL CODE LETTER R - PASSIVATE PER AMS 2700, TYPE 6 OR 7. f. MATERIAL CODE LETTER S - PASSIVATE PER AMS 2700, TYPE 6 OR 7. g. MATERIAL CODE LETTER T - ANODIZE PER AMS 2488, TYPE 2 OR FLUORIDE PHOSPHATE CONVERSION COAT PER AMS 2486. h. MATERIAL CODE LETTER W: 1. ANODIZE PER AMS 2472 OR MIL-A-
27、8625, TYPE II, CLASS 2, DYE BROWN, DUPLEX SEAL PER PROCUREMENT SPECIFICATION. 2. W CODE PARTS TO BE COATED WITH HIGH PURITY ALUMINUM ONLY WILL HAVE THE FINISH CODE LETTER “V” PLACED AFTER THE SIZE CODE IN THE PART NUMBER. THE FINISH WILL BE: COAT WITH HIGH PURITY ALUMINUM PER MIL-DTL-83488, CLASS 3,
28、 TYPE II, WITH MAXIMUM COATING THICKNESS OF .0005. GLASS BEAD PEEN PRESSURE SHALL BE 25 psi MAXIMUM. /23/ SEE PROCUREMENT SPECIFICATION FOR ADDITIONAL REQUIREMENTS. /4/ PROCUREMENT SPECIFICATION: AS4875/1 EXCEPT AS SPECIFIED ON THIS STANDARD. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTU
29、RED BY AN ACCREDITED MANUFACTURER LISTED IN THE NATIONAL AEROSPACE AND DEFENSE CONTRACTORS ACCREDITATION PROGRAM (NADCAP) QUALIFIED MANUFACTURER LIST FOR THIS PRODUCT TYPE. THE QML IS AVAILABLE AT WWW.EAUDITNET.COM./5/ IDENTIFICATION AT LOCATION SHOWN: MARK PER AS478 CLASS C OR D, OR METHOD 7A3, 15A
30、3 OR 15B. a. FOR SIZE 06 AND SMALLER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, LETTERS “AS”, AND MATERIAL CODE LETTER FOR CORROSION RESISTANT STEEL, TITANIUM AND ALUMINUM AND NO MATERIAL CODE LETTER FOR ALLOY STEEL.b. FOR SIZE 08 AND LARGER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, BASIC PART
31、NUMBER, AND MATERIAL CODE LETTER FOR CORROSION RESISTANT STEEL, TITANIUM AND ALUMINUM AND NO MATERIAL CODE LETTER FOR ALLOY STEEL.6. INVENTORIED PARTS CONFORMING TO THE PREVIOUS “LETTER CHANGE” MAY BE USED TO DEPLETION. /7/ FITTINGS WITH AS4396 STYLE S ENDS MAY BE ASSEMBLED INTO INTERNALLY THREADED
32、PORTS BUT ARE HISTORICALLY UNRELIABLE AND ARE ONLY SUITABLE IN THAT APPLICATION FOR 1500 psi MAXIMUM PRESSURE. FITTINGS WITH AS4396 STYLE G ENDS MAY BE DESIGNATED WITH THE SUFFIX G AFTER THE BASIC PART NUMBER AND CANNOT BE USED IN PORTS. 8. INTENDED USE: THIS PART IS DESIGNED FOR USE IN SYSTEMS WITH
33、 MAXIMUM OPERATING PRESSURES AS SHOWN IN TABLE 6. TABLE 6 - OPERATING PRESSURES FOR ASSOCIATED MATERIAL SIZE MATERIAL PSI 02-08 ALUMINUM ALLOY 3000 10-16 ALUMINUM ALLOY 150020 ALUMINUM ALLOY 100002-16 STEEL 3000 20 STEEL 150002-16 CORROSION RESISTANT STEEL 3000 20 CORROSION RESISTANT STEEL 1500 02-1
34、6 TITANIUM ALLOY 3000 20 TITANIUM ALLOY 1500 AEROSPACE STANDARD AS1032SHEET 6 OF 7REV. FFITTING, TEE, STANDARD AND REDUCER, BULKHEAD ON RUN, INTERNAL PORT ON RUN, FLARED 9. FOR REDUCER CONFIGURATIONS, THE PRESSURE RATING IS DETERMINED BY THE LARGEST PORT. 10. THE NON-REDUCER CONFIGURATION WITHOUT A
35、SUFFIX PART NUMBER CODE IS THE FUNCTIONAL EQUIVALENT OF AN784 AND MS24389 FOR THE CORRESPONDING FORGING SIZE AND IS INTENDED TO BE SUITABLE AS A REPLACEMENT STANDARD. 11. WHEN MACHINING FROM BAR STOCK OR OVERSIZED FORGING, THE CENTER BODY DIMENSIONS SHALL CONFORM TO AS1376, TABLE 11. /12/ DIMENSIONS
36、 “E” AND “F” ARE DETERMINED BY THE FORGING SIZE. /13/ THE DIMENSIONS IN THE TABLE ARE FOR FINAL MACHINED PARTS. THE FORGING SIZE IS DETERMINED AS THE SIZE NECESSARY TO MAKE THE LARGEST FITTING END. /14/ THE .125 MINIMUM DIMENSION APPLIES ONLY WHEN “Z” IS SPECIFIED. WHEN “Z” IS NOT SPECIFIED, USE “V”
37、 DIMENSION. /15/ WHEN “G” DIMENSION IS NOT SPECIFIED, USE “V” DIMENSION. /16/ WEIGHTS ARE FOR NON-REDUCERS ONLY. REDUCER FITTINGS WILL HAVE LOWER WEIGHTS. 17. THE CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL
38、 CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT. 18. INTERPRETATION OF DRAWING PER ARP4296. 19. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPEC
39、IFIED, MACHINED SURFACES TO BE 125 in Ra. FORGED SURFACES MAY BE 250 in Ra. 20. BREAK ALL SHARP EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 21. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994. 22. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .016, ANGULAR DIMENSI
40、ONS 0 DEGREES 30. /23/ EXAMPLE OF PART NUMBER: /24/ TITANIUM AND CADMIUM SHALL NOT BE USED FOR OXYGEN OR POTABLE WATER SYSTEMS. BASIC PART NUMBERSUFFIX CODE “G“ FOLLOWINGBASIP PART NUMBER ONLYFOR PARTS WITH AS4396STYLE G FITTING ENDS /7/MATERIAL CODE LETTER /1/AS1031 G J 10 10 10 VTHE FINISH LETTER
41、“V“ WILLBE PLACED HERE ONLY FORMATERIAL CODE LETTER “D“ AND “W“PARTS THAT ARE TO BE COATEDWITH HIGH PURITY ALUMINUM /3/SIZE CODE, TUBE SIZE OFPORT #3 IN .062 INCREMENTSSIZE CODE, TUBE SIZE OFPORT #2 IN .062 INCREMENTSSIZE CODE, TUBE SIZE OFPORT #1 IN .062 INCREMENTSAEROSPACE STANDARD AS1032SHEET 7 O
42、F 7REV. FFITTING, TEE, STANDARD AND REDUCER, BULKHEAD ON RUN, INTERNAL PORT ON RUN, FLARED /25/ INACTIVE MATERIAL CODES: a. PART NUMBERS WITH MATERIAL CODE LETTER D ARE INACTIVE FOR NEW DESIGN AS OF 2001-12. USE PART NUMBERS WITH MATERIAL CODE LETTER W FOR NEW DESIGN. b. PART NUMBERS WITH MATERIAL C
43、ODE LETTER S ARE INACTIVE FOR NEW DESIGN AS OF 2009-09. USE PART NUMBERS WITH MATERIAL CODE LETTER R FOR NEW DESIGN. /26/ THE SHOULDER IS NOT NEEDED BECAUSE THE FORGING BODY SIZE IS DESIGNED TO ACCOMMODATE THE INTERNAL BOSS PORT END, WHICH REQUIRES A LARGER BODY AND WALL THICKNESS. TO SEE HOW THE SH
44、OULDER IS USED REFER TO AS1033, AS1038 AND AS1040. 27. A CHANGE BAR (|) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
