1、AEROSPACE STANDARD INSTALLING AND REMOVAL TOOLS, CONNECTOR ELECTRICAL CONTACT, TYPE I, CLASS 1, COMPOSITION C AS81969/17Copyright 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, elect
2、ronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 201
3、4-02THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C2 FEDERAL SUPPLY CLASS 5120 AS81969/17SHEET 1 OF 4PROCUREMENT SPECIFICATION: AS81969SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirel
4、y voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised, reaffirmed, stabilized, orcancelled. SAE invites y
5、ourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS81969/17RATIONALE AS81969/17 PERMITS THE CANCELLATION AND SUPERSESSION OF MIL-I-81969/17 WITH THIS DOCUMENT. IT INCLUDES ENGINEERING POSITION LE
6、TTERS, MILITARY SPECIFICATION AMENDMENTS, AND MINOR TECHNICAL CHANGES REQUIRED TO REFLECT THE APPROVED QUALIFIED TOOLS. GOVERNMENT DOCUMENTATION REFERENCES ARE REMOVED. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF
7、AS81969. DETAIL A DASH-04,-05 AND -09 DETAIL B DASH-03 FIGURE 1 INSTALLING TOOL -03,-04,-05,-09 AEROSPACE STANDARD AS81969/17SHEET 2 OF 4INSTALLING AND REMOVAL TOOLS, CONNECTOR ELECTRICAL CONTACT, TYPE I, CLASS 1, COMPOSITION C FIGURE 2 REMOVAL TOOL -06, -07, -08 TABLE 1 TOOL CONFIGURATION (SEE FIGU
8、RE 1 AND 2) DASHNUMBER CONTACT SIZECOLOR CODE AMINCDIA D EDIAFDIAGDIA J HMINPDIA-03 20 RED .930 .134 .130.093.085.109.107.093.085- - .093 - -04 16 BLUE 2.127 .169 .159.090.080.133.128.101.098- .090 .080.130 - -05 12 YELLOW 2.127 .209 .189.121.118.179.177.147.144- .110 .100.173 - -06 8 RED - - - - -
9、.308 .305- - .263 .255-07 4 BLUE - - - - - .414 .411- - .378 .370-08 0 YELLOW - - - - - .606 .603- - .558 .550-09 20 RED 1.00 .134 .124.070.060.106.104.085.083- .063 .053.093 - AEROSPACE STANDARD AS81969/17SHEET 3 OF 4INSTALLING AND REMOVAL TOOLS, CONNECTOR ELECTRICAL CONTACT, TYPE I, CLASS 1, COMPO
10、SITION C REQUIREMENTS: ALL REQUIREMENTS SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81969. 1. CONFIGURATION: TOOL CONFIGURATION SHALL BE IN ACCORDANCE WITH FIGURES 1 AND 2 AND TABLE 1. DIMENSIONS AND TOLERANCES ARE IN ACCORDANCE WITH ANSI Y14.5M. DIMENSIONS ARE IN INCHES. UNLESS OTHERWI
11、SE SPECIFIED, TOLERANCE IS .005 ON THREE PLACE DECIMALS, .01 ON TWO PLACE DECIMALS, AND 4. BREAK AND BLEND ALL SHARP EDGES. HANDLE CONFIGURATION OPTIONAL WITHIN DIMENSIONS SHOWN (SEE REQUIREMENT 1). SLOT DESIGN (SEE FIGURE 1, DETAIL A) SHALL PERMIT ALL APPLICABLE WIRE SIZE DIAMETERS SPECIFIED FOR TH
12、E CONNECTORS TO FIT INTO THE TOOL FREELY (SEE TABLE 2). PROBE LENGTH DIMENSION PERMITS FULL CONTACT PENETRATION INTO CONNECTOR FOR THE CONNECTORS SPECIFIED (SEE TABLE 2). SURFACE ON THE EXTERIOR OF THE PROBES SHALL BE 32 MICROINCHES RMS MAX IN ACCORDANCE WITH ANSI B46.1. EACH TOOL SHALL BE FURNISHED
13、 WITH A PROBE PROTECTIVE CAP. THE CAP DESIGN AND MATERIAL IS OPTIONAL (SEE APPLICATION NOTE). 2. IDENTIFICATION MARKING: EACH TOOL SHALL BE LEGIBLY AND PERMANENTLY MARKED ON TOOL BODY IN ACCORDANCE WITH MIL-STD-130 (LOCATION OPTIONAL). SUPPLIER SYMBOL, IF USED, IT SHALL BE IN ACCORDANCE WITH AIR1351
14、. TOOL SIZES ARE IDENTIFIED BY THE COLOR SCHEMES ON THE HANDLE AS LISTED IN TABLE 1. 3. MATERIALS: HANDLE SHALL BE PLASTIC OR ALUMINUM IN ACCORDANCE WITH AS81969. IF PLASTIC IS USED, IT SHALL REMAIN STABLE AT 200 F (93.3 C) FOR 2 HOURS AS REQUIRED BY DEFLECTION UNDER LOAD TESTS APPROPRIATE FOR THE M
15、ATERIAL USED. SLOTTED PROBES SHALL BE STEEL IN ACCORDANCE WITH AS81969. 4. PART NUMBER: M81969 /17 -01 I I I I I I_DASH NUMBER (SEE TABLE 1) I I_ DETAIL SPECIFICATION NUMBER I_ BASIC SPECIFICATION NUMBER AEROSPACE STANDARD AS81969/17SHEET 4 OF 4INSTALLING AND REMOVAL TOOLS, CONNECTOR ELECTRICAL CONT
16、ACT, TYPE I, CLASS 1, COMPOSITION C APPLICATION NOTES: 1. TOOLS SHALL BE USED TO INSTALL CONTACTS IN CONNECTORS SPECIFIED IN TABLE 2. TABLE 2 TOOL APPLICATION PART NUMBER M81969/17 CONTACT SIZE HANDLE COLOR CODE CONNECTOR -03 20 RED MIL-DTL-26482 SERIES 1 CRIMP MIL-DTL-26500 MIL-DTL-26518 AS81703 SE
17、RIES II -04 16 BLUE MIL-DTL-26482, SERIES 1 CRIMP MIL-DTL-26500 MIL-DTL-26518 AS81703, SERIES 2 AS50151, SERIES AS34001-AS34121 MIL-C-38300 1/ AS81582 MIL-DTL-28748/9 AND /10 -05 12 YELLOW -09 20 RED -06 8 RED MIL-DTL-26518 AS50151, SERIES AS34001-AS34121 MIL-DTL-26500 -07 4 BLUE -08 0 YELLOW 1/ MIL
18、-C-38300 IS CANCELED (FOR FIELDED CONNECTORS ONLY). 2. TOOL SUPERSEDING PART NUMBERS ARE SHOWN TABLE 3. AS81969/17 DETAIL SPECIFICATION SUPERSEDES MIL-I-81969/17B AND MIL-I-81969/17B AMENDMENT 1 DETAIL SPECIFICATIONS. PART NUMBERS REMAIN UNCHANGED. TABLE 3 TOOL PART NUMBER SUPERSESSION PART NUMBER M
19、81969/17 SUPERSEDED PART NUMBERS -03 MS24256A20-04 MS24256A16M81969/17-01 MS90455-16 -05 MS24256A12M81969/17-02 MS90455-12 -06 MS90455-8-07 MS90455-4-08 MS90455-0 -09 MS24256B203. THE PROTECTIVE CAP (SEE FIGURE 1) MINIMIZES DAMAGE TO THE TIP AND IMPROVES PERSONNEL SAFETY. IF LOST, CONTACT THE SUPPLI
20、ER FOR REPLACEMENT. SPECIFICATION NOTE: 1. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
