1、SURFACEVEHICLESTANDARDJ561REAF.NOV2010Issued 1918-08Reaffirmed 2010-11Superseding J561 APR2006Electrical TerminalsEyelet and Spade Type1. ScopeThis SAE Standard covers general requirements and dimensions of various sizes of eyelet andspade type terminals.1.1 RationaleJ561 has been reaffirmed to comp
2、ly with the SAE 5-Year Review policy.2. References2.1 Applicable PublicationThe following publications form a part of this specification to the extent specifiedherein. The latest issue of SAE publications shall apply.2.1.1 SAE PUBLICATIONAvailable from SAE, 400 Commonwealth Drive, Warrendale, PA 150
3、96-0001, Tel:877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org.SAE J163Low Tension Wiring and Cable Terminals and Splice Clips3. General RequirementsThe eyelet and spade type terminals listed in Tables 1A and 1B and Figures 1through 5 of this document may be used for te
4、rminating wire ends or for terminating circuits on devices otherthan wire. Performance requirements for low tension wire terminals are specified in SAE J163.Terminal sizes other than those listed are permissible, providing they meet the general requirements of thisdocument and the performance requir
5、ements of SAE J163.Terminals shall be free from burrs, corrosion, or any foreign matter, and shall be of a temper that will permitattachment to wires or circuits on devices without fracturing or cracking.Terminals may be applied to wire by crimping, welding, swaging, soldering, or any combination th
6、ereof at theconductor grip. Insulation grips shall be used on all terminals assembled to 8 gage (8 mm2) and smallerinsulated wire except where usage provides other means of relieving strain.Materials should be of copper, brass, or other copper alloys. Minimum metal thickness is the nominalthickness
7、shown less a standard strip stock tolerance. Thickness is based on SAE CA260 (UNS C26000)brass conductivity and may be adjusted for use with other materials. Unless otherwise noted, all dimensionsshall be held to a tolerance of 0.25 mm ( 0.010 in).SAE Technical Standards Board Rules provide that: “T
8、his report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” SAE rev
9、iews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2010 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or tran
10、smitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SA
11、E WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/J561_201011 SAE J561 Reaffirmed NOV2010-2-TABLE 1AMETRIC STUD OR SCREW AND HOLE OR SLOT SIZESSAE No.Metric Stud orScrew SizeNominalMetric Stud orScr
12、ew SizeMaxHole orSlot SizeFor Eyeletor Spade,AMinHole orSlot SizeFor Eyeletor Spade,AMax1M M3 3.0 mm 3.2 mm 3.4 mm2M M4 4.0 mm 4.2 mm 4.4 mm3M M5 5.0 mm 5.3 mm 5.5 mm4M M6 6.0 mm 6.3 mm 6.5 mm5M M8 8.0 mm 8.4 mm 8.6 mm6M M10 10.0 mm 10.5 mm 10.7 mm7M M12 12.0 mm 12.5 mm 12.9 mm8M M14 14.0 mm 14.6 mm
13、 15.0 mm9M M16 16.0 mm 16.7 mm 17.1 mmTABLE 1BSTUD OR SCREW AND HOLE OR SLOT SIZESSAE No.Stud orScrew SizeNominalStud orScrew SizeMaxHole orSlot SizeFor Eyeletor Spade,AMinHole orSlot SizeFor Eyeletor Spade,AMax1 4 0.112 in 0.123 in 0.129 in2 6 0.138 in 0.144 in 0.150 in3 8 0.164 in 0.170 in 0.176 i
14、n4 10 0.190 in 0.201 in 0.207 in5 1/4 0.250 in 0.279 in 0.285 in6 5/16 0.313 in 0.342 in 0.348 in7 3/8 0.375 in 0.404 in 0.410 in8 7/16 0.438 in 0.466 in 0.476 in9 1/2 0.500 in 0.528 in 0.538 inSAE J561 Reaffirmed NOV2010-3-FIGURE 1STRAIGHT-TYPE EYELET AND SNAP-ON EYELET TERMINALSSAE J561 Reaffirmed
15、 NOV2010-4-FIGURE 2STRAIGHT-TYPE SPADE TERMINALSSAE J561 Reaffirmed NOV2010-5-FIGURE 3SIDE-TYPE SPADE TERMINALSSAE J561 Reaffirmed NOV2010-6-FIGURE 4SIDE-TYPE EYELET TERMINALSSAE J561 Reaffirmed NOV2010-7-FIGURE 5END-TYPE STARTING-CABLE TERMINALSPREPARED BY THE ELECTRICAL DISTRIBUTION SYSTEMS STANDARDS COMMITTEEREAFFIRMED BY THE SAE CONNECTOR SYSTEMS STANDARDS COMMITTEE
