1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA
2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any
3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-21927-7 SANS 2063:2008Edition 2ISO 2063:2005Edition 3SOUTH AFRICAN NATIONAL STANDARD Thermal spraying Metallic and other inorganic coating
4、s Zinc, aluminium and their alloys This national standard is the identical implementation of ISO 2063:2005 and is adopted with the permission of the International Organization for Standardization. Published by SABS Standards Division 1 Dr Lategan Road Groenkloof Private Bag X191 Pretoria 0001Tel: +2
5、7 12 428 7911 Fax: +27 12 344 1568 www.sabs.co.za SABS SANS 2063:2008 Edition 2 ISO 2063:2005 Edition 3 Table of changes Change No. Date Scope National foreword This South African standard was approved by National Committee SABS TC 107, Metallic and other inorganic coatings, in accordance with proce
6、dures of the SABS Standards Division, in compliance with annex 3 of the WTO/TBT agreement. This SANS document was published in November 2008. This SANS document supersedes SABS ISO 2063:1991 (first edition). Reference numberISO 2063:2005(E)ISO 2005INTERNATIONAL STANDARD ISO2063Third edition2005-03-0
7、1Thermal spraying Metallic and other inorganic coatings Zinc, aluminium and their alloys Projection thermique Revtements mtalliques et autres revtements inorganiques Zinc, aluminium et alliages de ces mtauxSANS 2063:2008This s tandard may only be used and printed by approved subscription and freemai
8、ling clients of the SABS .ISO 2063:2005(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer perform
9、ing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF
10、file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Sec
11、retariat at the address given below. ISO 2005 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the a
12、ddress below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2005 All rights reservedSANS 2063:2008This s tandard may only
13、be used and printed by approved subscription and freemailing clients of the SABS .ISO 2063:2005(E) ISO 2005 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing Inter
14、national Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison wit
15、h ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technica
16、l committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to
17、 the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 2063 was prepared by the European Committee for Standardization (CEN) in collaboration with Technical Committee ISO/TC
18、 107, Metallic and other inorganic coatings, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement). Throughout the text of this document, read “.this European Standard.” to mean “.this International Standard.”. This third edition cancels and replaces the se
19、cond edition (ISO 2063:1991), which has been technically revised. For the purposes of this International Standard, the CEN annex giving a list of EN documents corresponding to ISO documents mentioned as normative references has been removed. SANS 2063:2008This s tandard may only be used and printed
20、by approved subscription and freemailing clients of the SABS .ISO 2063:2005(E) iv ISO 2005 All rights reservedContents page Forewordv Introductionvi 1 Scope 1 2 Normative references 1 3 Terms and definitions .2 4 Manner of specifying requirements.2 5 Classification3 6 Manufacture3 6.1 Preparation of
21、 surfaces to be coated by thermal spraying.3 6.2 Coating metal .4 6.3 Thermal spraying.4 6.4 Sealing 4 6.5 Painting.4 7 Required characteristics.5 7.1 Thickness .5 7.2 Appearance 6 7.3 Adhesion.68 Test methods6 8.1 Measurement of thickness6 8.2 Adhesion test .7 Annex A (informative) Adhesion test me
22、thods 8 A.1 Grid test 8 A.2 Tensile test method .9 Annex B (informative) Recommendations for use.11 Bibliography12 SANS 2063:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 2063:2005(E) ISO 2005 All rights reserved vForeword This docu
23、ment (EN ISO 2063:2005) has been prepared by Technical Committee CEN/TC 240 “Thermal spraying and thermally sprayed coatings”, the secretariat of which is held by DIN, in collaboration with Technical Committee ISO/TC 107 “Metallic and other inorganic coatings”. This European Standard shall be given
24、the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2005, and conflicting national standards shall be withdrawn at the latest by September 2005. This document supersedes EN 22063:1993. Annex A and B are informative. This documen
25、t includes a Bibliography. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
26、 Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom SANS 2063:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 2063:2005(E) vi
27、ISO 2005 All rights reservedIntroduction Thermal-sprayed metallic coatings are produced by heating the coating metal to its molten stage and projecting it in a stream of gas onto the prepared surface to be coated. It is essential that the purchaser specifies the coating metal or alloy and the thickn
28、ess of the coating required: merely to ask for thermal metal spraying to be carried out in accordance with this standard, without this information, is insufficient. It is essential that the design of the article is such that it may be coated properly. SANS 2063:2008This s tandard may only be used an
29、d printed by approved subscription and freemailing clients of the SABS .ISO 2063:2005(E) ISO 2005 All rights reserved 11 Scope This standard applies to thermal-sprayed metallic coatings for the protection of iron and steel against corrosion by applying zinc or aluminium or their alloys to uncoated s
30、urface to be protected. This standard deals with characteristic properties and gives test methods for coatings obtained by the spraying of zinc and aluminium and their alloys for the general purpose of corrosion protection. It gives firstly the definition, classification and symbols for these coatin
31、gs in relation to their thickness. It then deals with the preparation of surfaces, application of coatings and their characteristic properties: namely, thickness, appearance and adhesion. Finally it gives test methods for checking these properties. For other metals some of the provisions are valid a
32、nd can be adopted by agreement between the interested parties. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document
33、 (including any amendments) applies. EN ISO 1463, Metallic and oxide coatings Measurement of coating thickness Microscopical method (ISO 1463:1982). EN ISO 2064:2000, Metallic and other inorganic coatings Definitions and conventions concerning the measurement of thickness (ISO 2064:1996). EN ISO 217
34、8, Non-magnetic coatings on magnetic substrates Measurement of coating thickness Magnetic method (ISO 2178:1982). EN ISO 8501-1, Preparation of steel substrates before application of paints and related products Visual assessment of surface cleanliness Part 1: Rust grades and preparation grades of un
35、coated steel substrates and of steel substrates after overall removal of previous coatings (ISO 8501-1:1988). EN ISO 11124-2, Preparation of steel substrates before application of paints and related products Specifications for metallic blast-cleaning abrasives Part 2: Chilled-iron grit (ISO 11124-2:
36、1993). EN ISO 11126-3, Preparation of steel substrates before application of paints and related products Specifications for non-metallic blast-cleaning abrasives Part 3: Copper refinery slag (ISO 11126-3:1993). EN ISO 11126-4, Preparation of steel substrates before application of paints and related
37、products Specifications for non-metallic blast-cleaning abrasives Part 4: Coal furnace slag (ISO 11126-4:1993). EN ISO 11126-7, Preparation of steel substrates before application of paints and related products Specifications for non-metallic blast-cleaning abrasives Part 7: Fused aluminium oxide (IS
38、O 11126-7:1995). EN ISO 12944-1, Paints and varnishes Corrosion protection of steel structures by protective paint systems Part 1: General introduction (ISO 12944-1:1998). EN ISO 12944-2, Paints and varnishes Corrosion protection of steel structures by protective paint systems Part 2: Classification
39、 of environments (ISO 12944-2:1998). EN ISO 12944-3, Paints and varnishes Corrosion protection of steel structures by protective paint systems Part 3: Design considerations (ISO 12944-3:1998). SANS 2063:2008This s tandard may only be used and printed by approved subscription and freemailing clients
40、of the SABS .ISO 2063:2005(E) 2 ISO 2005 All rights reservedEN ISO 12944-4, Paints and varnishes Corrosion protection of steel structures by protective paint systems Part 4: Types of surface and surface preparation (ISO 12944-4:1998). EN ISO 12944-5:1998, Paints and varnishes Corrosion protection of
41、 steel structures by protective paint systems Part 5: Protective paint systems (ISO 12944-5:1998). EN ISO 12944-6, Paints and varnishes Corrosion protection of steel structures by protective paint systems Part 6: Laboratory performance test methods (ISO 12944-6:1998). EN ISO 12944-7, Paints and varn
42、ishes Corrosion protection of steel structures by protective paint systems Part 7: Execution and supervision of paint work (ISO 12944-7:1998). EN ISO 12944-8, Paints and varnishes Corrosion protection of steel structures by protective paint systems Part 8: Development of specifications for new work
43、and maintenance (ISO 12944- 8:1998). EN ISO 14919:2001, Thermal spraying Wires, rods and cords for flame and arc spraying Classification Technical supply conditions (ISO 14919:2001). 3 Terms and definitions For the purposes of this European Standard, the terms and definitions given in EN ISO 2064:20
44、00 and the following apply. 3.1 significant surface part of the article covered or to be covered by the coating and for which the coating is essential for serviceability and/or appearance 3.2 minimum local thickness lowest value of the local thickness found on the significant surface of a single art
45、icle 4 Manner of specifying requirements When specifying the coating of articles by thermal spraying in accordance with this standard, the purchaser shall state, in addition to the number of the standard, the significant surface of the metal coating and its thickness in accordance with the symbols i
46、ndicated in Table 1. SANS 2063:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 2063:2005(E) ISO 2005 All rights reserved 35 Classification The zinc, aluminium or Zn-Al alloy coatings considered in this standard are classified in a sca
47、le according to their thickness, in conformity with the indications in Table 1. Table 1 Classification of sprayed metal coatings Minimum local thickness (m)a Thermal spray material according to EN ISO 14919 50b 100 150 200 250 300c Zn99,99 Al99,5 AlMg5 ZnAl15 This classification gives a series of th
48、ickness values applicable to zinc, aluminium and Zn-Al alloy coatings. Intermediate values may be specified by agreement between the parties concerned. The symbol corresponding to each coating shall be composed of the symbol according to EN ISO 14919 followed by the minimum local thicknessd. aIn con
49、formity with EN ISO 2064. bThicknesses requiring an agreement between the interested parties, notably on the spraying technique used to achieve uniformity of thickness, the use of paints or sealers and the test methods. cBy special agreement between the interested parties, greater minimum thicknesses may be used if the coating obtained remains in conformity with this standard. dTo specify an alloy coating, the chemical symbol corresponding to EN ISO 14919 shal
