SIS SS-EN 60 439-3-1991 Low-vo tage switchgear and controlgear assemblies Part 3 Particular requirements for low-voltage switchgear and controlgear assemblies intended to be instace.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

NF E62-182-1983 Machine tools Horizontal internal broaching machines Designation Dimensions Characteristics 《机床 卧式内拉床 名称、尺寸和特征》.pdf

NF E62-183-1983 Pullers with 4 clamps for internal pull-type broaching Part 1 general 《内拉式拉削用带四个夹具的拉出器 第1部分 总则》.pdf

NF E62-185-1983 Pullers with 4 clamps for internal pull-type broaching Part 3 dimensions and characteristics of pullers for broaches of diameters 28 to 32 《内拉削用带四个夹具的拉出器 第3部分 直径28.pdf

NF E62-190-1989 Tail end head with two catch fingers for pull broaching Dimensions and characteristics of heads for broaching tools of diameters 4 to 50 《拉削用的带两个卡销的尾挂钩头 直径4到50拉刀的主轴.pdf

NF E62-196-1989 Machine-tools Retriever for internal push type broaching with full ends shape W Part 1 general 《机床 内孔后推式拉削刀具端头 SW型 W形状 第1部分 总则》.pdf

NF E62-197-1989 Machines-tools Pushing head type uv for internal push type broaching with tail ends shape U or V Part 1 general 《机床 U或V形尾端的内推式拉削的UV 型顶推头 第1部分 总则》.pdf

NF E62-277-1996 Modular units for machine tool construction Support brackets 《机床结构的模块装置 支承座》.pdf

NF E62-317-1993 Modular units for machine tools Workholding pallets Part 2 workholding pallets of nominal size greater than 800 mm 《机床的模块装置 工件夹持托盘 第2部分 公称尺寸大于800毫米的较厚的工件夹持托盘》.pdf

NF E62-331-1992 Machine tools Modular units Modular clamping and mounting device for piece Generalities 《机床 模块装置 工件夹紧和安装用的模块装置 概述》.pdf