1、Designation: F3123 18a An American National StandardStandard Specification forMetric Outside Diameter Polyethylene (PE) Plastic Pipe (DR-PN)1This standard is issued under the fixed designation F3123; the number immediately following the designation indicates the year oforiginal adoption or, in the c
2、ase of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers metric outside diameter poly-ethylene (PE) pipe made from poly
3、ethylene compound thatqualifies for MRS, HDB and HDS ratings and for PE100 andPE4710 designations. Included are requirements for polyeth-ylene compound, workmanship, dimensions, short-term stressand ductility, long-term stress, marking, quality assurance andverification of joining.1.1.1 Polyethylene
4、 pipe in accordance with Table 1 isintended to be compatible with nominal diameters in accor-dance with ISO 161-1, Specification D3035 and other pipesizing conventions, nominal pressures in accordance with ISO161-1 and wall thickness in accordance with ISO 4065.1.1.2 Polyethylene pipe in accordance
5、with Table 2 isintended to be outside diameter compatible with steel pipeNPS/IPS nominal outside diameter pipe in accordance withspecifications such as Specification D3035, Specification F714,or AWWA C906.1.1.3 Polyethylene pipe in accordance with Table 3 isintended to be outside diameter compatible
6、 with cast iron/ductile iron, DIPS/DIOD outside diameter pipe in accordancewith specifications such as Specification D3035, SpecificationF714, or AWWA C906.1.2 Pipes produced under this specification are intended forthe pressure or non-pressure conveyance of liquid or gaseousmedia. Pipes produced un
7、der this specification are not intendedas enclosures for electrical or communications components.See Appendix X1.1.3 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.1.4 The following safety hazards caveat pertains only to thetes
8、t methods portion, Section 7, of this specification: Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It is the responsibility of the userof this standard to establish appropriate safety, health, andenvironmental practices and determine the applica
9、bility ofregulatory limitations prior to use.1.5 The ANS label on this international standard certifies thedevelopment of this international standard in accordance withrequirements for openness, balance, consensus and due processin accordance with ANSI Essential Requirements: Due ProcessRequirements
10、 for American National Standards and denotes inaddition that this international standard is an American Na-tional Standard.1.6 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDeve
11、lopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD638 Test Method for Tensile Properties of PlasticsD746 Test
12、 Method for Brittleness Temperature of Plasticsand Elastomers by ImpactD792 Test Methods for Density and Specific Gravity (Rela-tive Density) of Plastics by DisplacementD1238 Test Method for Melt Flow Rates of Thermoplasticsby Extrusion PlastometerD1435 Practice for Outdoor Weathering of PlasticsD15
13、05 Test Method for Density of Plastics by the Density-Gradient TechniqueD1598 Test Method for Time-to-Failure of Plastic PipeUnder Constant Internal PressureD1599 Test Method for Resistance to Short-Time HydraulicPressure of Plastic Pipe, Tubing, and FittingsD1600 Terminology for Abbreviated Terms R
14、elating to Plas-ticsD1603 Test Method for Carbon Black Content in OlefinPlastics1This specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.26 on OlefinBased Pipe.Current edition approved Nov. 1, 2018. Published De
15、cember 2018. Originallyapproved in 2015. Last previous edition approved in 2018 as F312318. DOI:10.1520/F312318A2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the
16、standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internatio
17、nally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.1D2122 Test Method for Determining Dimensions of Ther-
18、moplastic Pipe and FittingsD2290 Test Method for Apparent Hoop Tensile Strength ofPlastic or Reinforced Plastic PipeD2565 Practice for Xenon-Arc Exposure of Plastics In-tended for Outdoor ApplicationsD2837 Test Method for Obtaining Hydrostatic Design Basisfor Thermoplastic Pipe Materials or Pressure
19、 Design Basisfor Thermoplastic Pipe ProductsD3035 Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside DiameterD3350 Specification for Polyethylene Plastics Pipe and Fit-tings MaterialsD3895 Test Method for Oxidative-Induction Time of Poly-olefins by Differential Scan
20、ning CalorimetryD4218 Test Method for Determination of Carbon BlackContent in Polyethylene Compounds By the Muffle-Furnace TechniqueF412 Terminology Relating to Plastic Piping SystemsF714 Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside DiameterF905 Practice for Qualificatio
21、n of Polyethylene Saddle-Fused JointsF1055 Specification for Electrofusion Type PolyethyleneFittings for Outside Diameter Controlled Polyethyleneand Crosslinked Polyethylene (PEX) Pipe and TubingF1056 Specification for Socket Fusion Tools for Use inSocket Fusion Joining Polyethylene Pipe or Tubing a
22、ndFittingsF1290 Practice for Electrofusion Joining Polyolefin Pipe andFittingsF1473 Test Method for Notch Tensile Test to Measure theResistance to Slow Crack Growth of Polyethylene Pipesand ResinsF2620 Practice for Heat Fusion Joining of Polyethylene Pipeand FittingsTABLE 1 Diameter and Wall Thickne
23、ss Dimensions and Tolerances, mmNominalDiameter,DNOutside DiameterMinimum Wall Thickness, tPN 25 PN 20 PN 16 PN 12.5 PN 10 PN 8 PN 6 PN 5Min.(dn)Tol.OORTol.DR 7.4 DR 9 DR 11 DR 13.6 DR 17 DR 21 DR 26 DR 33tTol.AtTol.AtTol.AtTol.AtTol.AtTol.AtTol.AtTol.A32 32 0.3 1.3 44 0.6 3.6 0.5 3 0.4 . . . . . .
24、. . . .40 40 0.4 1.4 5.5 1.7 4.5 0.6 3.7 0.5 3.0 0.5 . . . . . . . .50 50 0.4 1.4 6.9 1.8 5.6 0.7 4.6 0.6 3.7 0.5 3.0 0.4 . . . . . .63 63 0.4 1.5 8.6 1 7.1 0.9 5.8 0.7 4.7 0.5 3.8 0.5 3 0.4 . . . .75 75 0.5 1.6 10.3 1.2 8.4 1 6.8 0.8 5.6 0.6 4.5 0.6 3.6 0.5 . . . .90 90 0.6 1.8 12.3 1.5 10.1 1.2 8.
25、2 1 6.7 0.8 5.4 0.7 4.3 0.6 3.5 0.5 . .110 110 0.7 2.2 15.1 1.7 12.3 1.4 10 1.1 8.1 1 6.6 0.8 5.3 0.7 4.2 0.6 . .125 125 0.8 2.5 17.1 1.9 14 1.6 11.4 1.3 9.2 1.1 7.4 0.9 6 0.7 4.8 0.6 . .140 140 0.9 2.8 19.2 2.1 15.7 1.7 12.7 1.4 10.3 1.2 8.3 1 6.7 0.8 5.4 0.7 . .160 160 1 3.2 21.9 2.3 17.9 1.9 14.6
26、 1.6 11.8 1.3 9.5 1.1 7.7 0.9 6.2 0.8 . .180 180 1.1 3.6 24.6 2.6 20.1 2.2 16.4 1.8 13.3 1.5 10.7 1.2 8.6 1 6.9 0.8 . .200 200 1.2 4 27.4 2.9 22.4 2.4 18.2 2 14.7 1.5 11.9 1.3 9.6 1.1 7.7 0.9 . .225 225 1.4 4.5 30.8 3.2 25.2 2.7 20.5 2.2 16.6 1.8 13.4 1.5 10.8 1.2 8.6 1 . .250 250 1.5 5 34.2 3.6 27.
27、9 4.2 22.7 2.4 18.4 2 14.8 1.6 11.9 1.3 9.6 1.1 . .280 280 1.7 9.8 38.3 4 31.3 4.7 25.4 2.7 20.6 2.2 16.6 1.8 13.4 1.5 10.7 1.2 . .315 315 1.9 11.1 43.1 4.5 35.2 5.3 28.6 3 23.2 2.3 18.7 2 15 1.6 12.1 1.4 9.7 1.1355 355 2.2 12.5 48.5 5 39.7 6 32.2 4.9 26.1 2.8 21.1 2.3 16.9 1.8 13.6 1.5 10.9 2.2400
28、400 2.4 14 54.7 5.6 44.7 6.8 36.3 5.5 29.4 3.1 23.7 2.5 19.1 2.1 15.3 1.7 12.3 2.4450 450 2.7 15.8 61.5 6.3 50.3 7.6 40.9 6.2 33.1 4.9 26.7 2.8 21.5 2.3 17.2 1.9 13.8 2.7500 500 3 17.5 68.4 10.3 55.8 8.4 45.4 6.9 36.8 5.5 29.7 2.9 23.9 2.5 19.1 2.1 15.3 2.7560 560 3.4 19.6 76.6 11.5 62.5 9.4 50.8 7.
29、7 41.2 6.1 33.2 4.9 26.7 2.8 21.4 2.3 17.2 2.9630 630 3.8 22.1 86.1 13 70.3 10.6 57.2 8.7 46.3 6.9 37.4 5.6 30 4.5 24.1 2.6 19.3 3.1710 710 6.4 24.9 97.1 14.5 79.3 12 64.5 9.8 52.2 7.8 42.1 6.3 33.9 5 27.2 2.9 21.8 3.3800 800 7.2 28 109.3 16.3 89.3 13.5 72.6 11 58.8 8.8 47.4 7.1 38.1 5.7 30.6 4.5 24
30、.5 3.6900 900 8.1 31.5 . . 100.6 15 81.7 12.4 66.2 9.9 53.3 7.9 42.9 6.4 34.4 5.1 27.6 3.91000 1000 9 35 . . 111.8 16.7 90.2 13.7 72.5 10.8 59.3 8.8 47.7 7.1 38.2 5.7 30.6 4.51200 1200 10.8 42 . . . . 109.5 16.4 88.2 13.2 67.9 10.1 57.2 8.5 45.9 6.8 36.7 5.51400 1400 12.6 49 . . . . . . 102.9 15.4 8
31、2.4 12.3 66.7 10 53.5 8 42.9 6.41600 1600 14.4 56 . . . . . . 117.6 17.6 94.1 14.1 76.2 11.4 61.2 9.1 49 7.31800 1800 16.2 63 . . . . . . . . 105.9 15.8 85.7 12.8 69.1 10.3 54.5 8.12000 2000 18 70 . . . . . . . . 117.6 17.6 95.2 14.2 76.9 11.5 60.6 92100 2100 18.9 73.5 . . . . . . . . . . 100 15 80.
32、8 12.2 63.6 9.62250 2250 20.3 78.7 . . . . . . . . . . 107.2 16.1 86 12.9 68.2 10.22300 2300 20.7 80.5 . . . . . . . . . . 109.5 16.5 88.5 13.3 69.7 10.52500 2500 22.5 87.5 . . . . . . . . . . 119 17.9 96.2 14.5 75.8 11.4AFor minimum wall #30.0 mm, tolerance equals 0.1 minimum wall, rounded up to th
33、e nearest 0.1 mm. For minimum wall 30.0 mm, tolerance equals 0.15 minimumwall, to nearest whole 0.1 mm, with decimal values beyond 0.1 mm dropped.F3123 18a2TABLE2NPS/IPSDiameterandWallThicknessDimensionsandTolerances,mmNPS/IPSNominalSizeAOutsideDiameterAPN25.5DR7.3APN20DR9APN16DR11APN12.8DR17APN10DR
34、21APN8DR21APN6.4DR26APN5.08DR32.5AdntoltoltTolBtTolBtTolBtTolBtTolBtTolBtTolBtTolB133.30.31.34.60.63.80.53.10.52.50.42.00.31.70.31.30.3.11442.00.31.45.80.74.70.63.90.53.10.52.50.42.10.41.70.3.11248.10.31.46.60.85.40.74.40.63.60.52.90.42.40.41.90.3.260.20.31.58.31.06.80.85.50.74.50.63.60.52.90.42.40.
35、42.20.4388.70.41.812.21.410.01.18.11.06.60.85.30.74.30.63.40.53.30.54114.10.52.315.61.712.81.410.51.28.41.06.80.85.50.74.40.64.20.66168.00.63.423.02.418.82.015.41.712.41.410.01.18.11.06.50.86.20.88218.70.74.429.94.524.52.620.02.116.11.813.01.410.61.28.41.08.00.910272.70.85.537.35.630.54.624.92.620.1
36、2.216.21.813.21.510.51.210.01.112323.40.96.544.26.736.25.529.54.523.82.519.22.115.61.712.41.411.91.314354.03.27.148.47.339.66.032.34.926.02.721.02.217.11.913.61.513.01.416404.63.78.155.38.345.36.836.95.629.74.524.02.519.52.115.51.714.81.618455.14.19.262.29.450.97.741.56.333.55.127.02.822.02.317.51.9
37、16.71.820505.74.610.269.110.456.68.546.27.037.25.630.04.524.42.619.42.118.52.022556.35.019.576.111.562.29.450.87.740.96.233.05.026.82.821.42.320.42.224606.95.521.383.012.567.910.255.48.444.66.736.05.429.34.423.32.522.22.426657.45.923.1.73.511.160.09.048.37.339.05.931.74.825.22.724.12.628708.06.424.8
38、.79.211.964.69.752.07.842.06.334.15.227.24.125.92.730758.66.926.6.84.812.869.210.455.78.445.06.836.65.529.14.427.84.232809.17.328.4.90.513.673.811.159.49.048.07.239.05.931.04.729.64.534859.77.830.1.78.411.863.29.551.07.741.46.333.05.031.54.836910.38.231.9.83.112.566.910.154.08.143.96.634.95.333.35.0
39、421062.09.637.2.78.011.763.09.551.27.740.76.238.95.9481213.711.042.5.89.113.472.010.858.58.846.57.044.46.7541365.412.347.8.81.012.265.89.952.37.949.97.5631593.014.455.8.76.711.661.19.258.38.8651643.614.957.6.79.211.963.09.560.19.1ANPSIPSNominalSize,outsidediameter,andDRconsistentwithSpecificationD30
40、35.Theoutsidediameter,dn,isaminimumandthetoleranceisplusonly.BForminimumwall30.0mm,toleranceequals0.15minimumwall,tonearestwhole0.1mm,withdecimalvaluesbeyond0.1mmdropped.F3123 18a3F2928 Practice for Specimens and Testing Conditions forTesting Polyethylene (PE) Pipe Butt Fusions Using Ten-sile and Hy
41、drostatic Test MethodsG155 Practice for Operating Xenon Arc Light Apparatus forExposure of Non-Metallic Materials2.2 ISO Documents3ISO 161-1 Thermoplastics pipes for the conveyance offluidsNominal outside diameters and nominalpressuresPart 1: Metric seriesISO 4065 Thermoplastics pipesUniversal wall
42、thicknesstableISO 4437 Plastic piping systems for the supply of gaseousfuelsISO 9000 Quality managementISO 9080 Plastics piping and ducting systemsDetermination of the long-term hydrostatic strength ofthermoplastics materials in pipe form by extrapolationISO 12162 Thermoplastics materials for pipes
43、and fittingsfor pressure applicationsClassification anddesignationOverall service (design) coefficientISO 13477 Thermoplastics pipes for the conveyance offluidsDetermination of resistance to rapid crack propa-gation (RCP)Small-scale steady-state test (S4 test)ISO 13478 Thermoplastics pipes for the c
44、onveyance offluidsDetermination of resistance to rapid crack propa-gation (RCP)Full-scale test (FST)ISO 16871 Plastics piping and ducting systemsPlasticspipes and fittingsMethod for exposure to direct (natural)weatheringISO 18553 Method for the assessment of the degree ofpigment or carbon black disp
45、ersion in polyolefin pipes,fittings and compounds2.3 NSF International Standards:4NSF/ANSI Standard No. 14 for Plastic Piping Componentsand Related MaterialsNSF/ANSI Standard No. 61 for Drinking Water SystemComponentsHealth Effects2.4 PPI Documents:5TR-3 Policies and Procedures for Developing Hydros
46、taticDesign Basis (HDB), Pressure Design Basis (PDB),Strength Design Basis (SDB), and Minimum RequiredStrength (MRS) Ratings for Thermoplastic Piping Mate-rials or PipeTR-4 Listing of Hydrostatic Design Bases (HDB), StrengthDesign Bases (SDB), Pressure Design Bases (PDB) andMinimum Required Strength
47、 (MRS) Ratings forThermo plastic Piping Materials or PipeTN-30 Requirements for the Use of Rework Materials inManufacturing of Polyethylene Gas PipeHandbook of Polyethylene Pipe, Second Edition2.5 Other Documents:ANSI Essential Requirements : Due process requirementsfor American National Standards6A
48、S/NZS 4130 Polyetheylene (PE) Pipes for Pressure Appli-cations7Decision on Principles for the Development of InternationalStandards , Guides and Recommendations8Guidelines for Drinking-Water Quality, Third Edition Incor-porating the First and Second Addenda, Volume 1:Recommendations, World Health Or
49、ganization, Geneva,200893Available from International Organization for Standardization (ISO), 1, ch. dela Voie-Creuse, CP 56, CH-1211 Geneva 20, Switzerland, http:/www.iso.org.4Available from NSF International, P.O. Box 130140, 789 N. Dixboro Rd., AnnArbor, MI 48105, http:/www.nsf.org.5Available from Plastics Pipe Institute (PPI), 105 Decker Court, Suite 825,Irving, TX 75062, http:/www.plasticpipe.org.6Available from the American National Standards Institute (ANSI) at https:/share.ansi.org/shared%20documents/
