1、Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-FOREWORD IS0 (the International Organization for Standardization) is a worldwide federation of national standards institut
2、es (IS0 member bodies). The work of developing International Standards is carried out through IS0 technical committees. Every member body interested in a subject for which a technical committee has been set up has the right to be represented on that committee. International organizations, government
3、al and non-governmental, in liaison with ISO, also take part in the work. Draft International Standards adopted by the technical committees are circulated to the member bodies for approval before their acceptance as International Standards by the IS0 Council. International Standard IS0 4418 was deve
4、loped by Technical Committee ISO/TC 133, Sizing systems and designations for clothes, and was circulated to the member bodies in September 1977. It has been approved by the member bodies of the following countries : Australia Canada Finland France Hungary India I ran Ireland South Africa, Rep. of Is
5、rael Spain Japan Sweden Netherlands Turkey New Zealand U.S.A. Poland U.S.S. R. Romania Yugoslavia The member bodies of the following countries expressed disapproval of the document on technical grounds : Germany Switzerland United Kingdom 0 International Organization for Standardization, 1978 Printe
6、d in Switzerland Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-INTERNATIONAL STANDARD IS0 4418-1978 (E) 4438-78 I 4853903 0033b3 T Size designation of clothes - Gloves
7、O INTRODUCTION This International Standard is one of a series which deals essentially with the size designation of clothing, and is not directly concerned with sizing systems as such. The primary aim of this and other International Standards in this series is the establishment of a size designation
8、system that indicates (in a simple, direct and meaningful manner) the body size of the person that a garment is intended to fit. Provided that the shape of the persons body (as indicated by the appropriate dimensions) has been accurately determined, this system will facilitate the choice of garments
9、 that fit. The size designation system is based on body and not garment measurements. Choice of garment measurements is normally left to the designer and the manufacturer, who are concerned with style, cut and other fashion elements, and who must make due allowance for garments normally worn beneath
10、 a specific garment. Definitions and body measurement procedure are prescribed in IS0 3635, which is applicable to all categories of cl o th i ng . 1 This International Standard establishes a system of designating the sizes of gloves. Both the control dimensions on which the size designation system
11、is based, and the method of indicating the size designation on a garment label, are laid down. SCOPE AND FIELD OF APPLICATION 2 REFERENCE This International Standard should be read in conjunction with the following International Standard : IS0 3635, Size designation of clothes - Definitions and body
12、 measurement procedure. - 3 CONTROL DIMENSIONS The control dimensions shall be as follows : a) Hand girth at knuckles. b) Hand length. 4 SIZE DESIGNATION 4.1 The size designation. shall comprise the control dimensions (see clause 31, in centimetres, of the intended wearer of that garment. The releva
13、nt control measurements shall be given, preferably preceded by the descriptive words “hand girth“ (at knuckles) and “hand length“, in that order. NOTE - The above requirements shall not preclude the use, in exceptional instances and as specified by the national standards organization concerned, of a
14、) size designations comprising only one of the applicable control dimensions; b) size designations shown as a range by stating the minimum and maximum control measurements separated by an oblique stroke or a hyphen. 4.2 Garment measurements shall not be incorporated in the size designation but, wher
15、e considered of value, garment measurements may be indicated separately (see 5.3). 5 LABELLING 5.1 Method The size designation of each garment shall be indicated clearly, conspicuously and in plainly legible form on a label, or on a swing ticket, or on both. 5.2 Attachment The label or swing ticket
16、shall be securely attached to the garment and so positioned as to be easily readable. 5.3 Additional information Information additional to the size designation may be separately indicated on the label, or on the swing ticket, or on both, provided that it does not in any way reduce the prominence and
17、 conspicuousness of the size designation. Such additional information may include a size code number or garment measurements considered to constitute useful information. . - -. .= - ._ . . . - . . Copyright International Organization for Standardization Provided by IHS under license with ISONot for
18、ResaleNo reproduction or networking permitted without license from IHS-,-,-IS0 4418-1978 (E) 4438-70 14853703 0033862 1 r 5.4 Examples of labels The examples of labels given in the figure illustrate methods of labelling that range from the simple indication of the relevant control measurements to mo
19、re elaborate forms that provide additional information, such as a garment group only. measurement or a size code number. Where the size designation is supplemented by a size code number, separation of the two, as illustrated, renders the size code number recognizable as being part of a system of siz
20、e designation adopted by a national or limited population a) Mans gloves b) Childs stretch gloves HAND GIRTH/HAND LENGTH 23/21 I HAND LENGTH 11-15 HAND GIRTH I c) Womans evening gloves HAND LENGTH 14 SIZE CODE 6 1/2 SHOULDER LENGTH (20 B.L.) FIGURE - Examples of labels for glows 1) Example of additional information included in accordance with sub-clause 5.3. 7 _ 2 Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
