ABS 115 NOTICE 1-2013 COMMENTARY ON THE GUIDE FOR FATIGUE ASSESSMENT OF OFFSHORE STRUCTURES.pdf

上传人:proposalcash356 文档编号:400527 上传时间:2018-10-27 格式:PDF 页数:2 大小:31.17KB
下载 相关 举报
ABS 115 NOTICE 1-2013 COMMENTARY ON THE GUIDE FOR FATIGUE ASSESSMENT OF OFFSHORE STRUCTURES.pdf_第1页
第1页 / 共2页
ABS 115 NOTICE 1-2013 COMMENTARY ON THE GUIDE FOR FATIGUE ASSESSMENT OF OFFSHORE STRUCTURES.pdf_第2页
第2页 / 共2页
亲,该文档总共2页,全部预览完了,如果喜欢就下载吧!
资源描述

1、 ABSCOMMENTARY ON THE GUIDE FOR THE FATIGUE ASSESSMENT OF OFFSHORE STRUCTURES .2004 1 COMMENTARY ON THE GUIDE FOR FATIGUE ASSESSMENT OF OFFSHORE STRUCTURES (APRIL 2003) JANUARY 2004 NOTICE NO. 1 February 2013 The following changes become EFFECTIVE AS OF 1 FEBRUARY 2013. (See http:/www.eagle.org for

2、the consolidated version of the Commentary on the Guide for Fatigue Assessment of Offshore Structures (April 2003), 2004, with all Notices and Corrigenda incorporated.) Notes - The date in the parentheses means the date that the Rule becomes effective for new construction based on the contract date

3、for construction. (See 1-1-4/3.3 of the ABS Rules for Conditions of Classification Offshore Units and Structures (Part 1).) SECTION 3 S-N CURVES 4 Tubular Intersection Connections (Revise Paragraph 3/4.2, as follows.) 4.2 With Weld Improvement (1 February 2013) A summary of the API and HSE/DEn S-N c

4、urves for joints of tubular members having weld improvement is presented in the following. API RP 2A(2000) uses the X curve for the following three corrosion cases with various endurance limits: In-air, endurance limit = 107cycles Cathodic protection, endurance limit = 2 108cycles Free corrosion in

5、seawater, no endurance limit. The crediting of weld profile control (i.e., concave weld profile) and other fatigue strength enhancements are not mentioned in the Guide for use with the ABS S-N curves. The main reason for this is to discourage (however, not ban) the use of such a credit in design. In

6、 this way, the credit will be available if needed in the future say, if design changes occur after structural fabrication begins and even later in the structures life should reconditioning or reuse be considered. Out of necessity and in a limited, particular circumstance, the Guide (in its Appendix

7、3) allows the use of the API X curve, which requires weld profile control and NDE. Grinding is preferably to be carried out by rotary burr and to extend below the plate surface in order to remove toe defects and the ground area is to have effective corrosion protection. The treatment is to produce a

8、 smooth concave profile at the weld toe with the depth of the depression penetrating into the plate surface to at least 0.5 mm below the bottom of any visible undercut. The depth of groove produced is to be kept to a minimum, and, in general, kept to a maximum of 1 mm. In no circumstances is the gri

9、nding depth to exceed 2 mm or 7% of the plate gross thickness, whichever is smaller. Grinding has to extend to areas well outside the highest stress region. Notice No. 1 February 2013 2 ABSCOMMENTARY ON THE GUIDE FOR THE FATIGUE ASSESSMENT OF OFFSHORE STRUCTURES .2004 The finished shape of a weld su

10、rface treated by ultrasonic/hammer peening is to be smooth and all traces of the weld toe are to be removed. Peening depth below the original surface is to be maintained at least 0.2 mm. Maximum depth is generally not to exceed 0.5 mm. Provided these recommendations are followed, when using the ABS

11、S-N curves, a credit of 2 on fatigue life may be permitted when suitable toe grinding or ultrasonic/hammer peening are provided. Credit for an alternative life enhancement measure may be granted based on the submission of a well-documented, project-specific investigation that substantiates the claimed benefit of the technique to be used.

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 标准规范 > 国际标准 > 其他

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1