1、ASD STANDARD NORME ASD ASD NORM prEN 3545-009 Edition P 1 December 2006 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATION Gulledelle 94 - B-1200 Brussels - Tel. + 32 2 775 8126 - Fax. + 32 2 763 3565 - www.asd-stan.orgICS: 49.060 Descriptors: ENGLISH VERSION A
2、erospace series Connectors, electrical, rectangular, with sealed and non-sealed rear, plastic housing, locking device, operating temperatures 55 C to 175 C Part 009: Protective cover for plug and receptacle Product standard Srie arospatiale Connecteurs lectriques, rectangulaires, tanches et non tanc
3、hes larrire, botier en plastique, verrouillage, tempratures dutilisation 55 C 175 C Partie 009 : Capot de protection pour fiche et embase Norme de produit Luft- und Raumfahrt Elektrische Rechtecksteckverbinder mit und ohne hintere Abdichtung, Plastikgehuse, Verriegelungssystem, Betriebstemperaturen
4、von 55 C bis 175 C Teil 009: Schutzkappe fr festen und freien Steckverbinder Produktnorm This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization). It is published for the needs of the Eur
5、opean Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, wit
6、hout re-identification of the standard. After examination and review by users and formal agreement of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national
7、 members have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Edition approved for publication 31 December 2006 Comments should be sent within six months after the date of publication to
8、ASD-STAN Electrical Domain Copyright 2006 by ASD-STAN Copyright European Association of Aerospace Industries Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 3545-009:20062 Contents Page Foreword2 1 Scope 3 2 Normative r
9、eferences 3 3 Terms and definitions .3 4 Required characteristics.3 5 Designation 5 6 Marking .6 7 Technical specification .6 Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Electrical Domain. After inquiries and votes carried out in accordance with the rules of
10、ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. Copyright European Association of Aerospace Industries Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 3545-009:
11、2006 3 1 Scope This standard specifies the characteristics of protective cover for plug and receptacle in the family of rectangular electrical connectors with sealed and non-sealed rear, plastic housing, locking device, for operating temperatures from 55 C to 175 C. The protective covers are not abl
12、e to ensure a sealing in immersion condition. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any a
13、mendments) applies. EN 3545-001, Aerospace series Connectors, electrical, rectangular, with sealed and non-sealed rear, plastic housing, locking device, operating temperatures 55 C to 175 C Part 001: Technical specification. EN 3545-002, Aerospace series Connectors, electrical, rectangular, with sea
14、led and non-sealed rear, plastic housing, locking device, operating temperatures 55 C to 175 C Part 002: Specification of performance and contact arrangements. EN 3545-005, Aerospace series Connectors, electrical, rectangular, with sealed and non-sealed rear, plastic housing, locking device, operati
15、ng temperatures 55 C to 175 C Part 005: Female coding and attachment system for mounting on free housing (plug) Product standard. 1)EN 3545-006, Aerospace series Connectors, electrical, rectangular, with sealed and non-sealed rear, plastic housing, locking device, operating temperatures 55 C to 175
16、C Part 006 : Male coding and attachment system for mounting on fixed housing (receptacle) Product standard. 1)3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 3545-001 apply. 4 Required characteristics 4.1 Dimensions and mass See Figure 1. Dimensions a
17、nd tolerances are in millimetres. Mass: with attachments: 19 g max.; without attachment: 9 g max. The female attachment system corresponds to EN 3545-005 without the locating coding device (half moon), see Figure 2. The male attachment system corresponds to EN 3545-006 without the locating coding de
18、vice (half moon), see Figure 3. 1) Published as AECMA Prestandard at the date of publication of this standard. Copyright European Association of Aerospace Industries Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 3545-
19、009:20064 Key 1 Part number 5 Optional chain or cable (length (80 5) mm) 2 Molding batch 6 Attachment system for mounting on free housing 3 Codable for mounting connector with pins 7 Seal 4 Attachment system for mounting on fixed housing 8 Codable for mounting connector with sockets Figure 1 Figure
20、2 Female attachment system Figure 3 Male attachment system 1 2 3 57 4 7 68 Socket interface Pin interface Copyright European Association of Aerospace Industries Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 3545-009:2
21、0065 4.2 Recommended panel cut-out for fixed housing (receptacle) fitted with male attachment system See Figure 4. Maximum thickness of panel: 1,6 Minimum pitch between connectors: 14,2 Figure 4 4.3 Main general characteristics See EN 3545-002. 5 Designation EXAMPLE Description block COVER, ELECTRIC
22、AL CONNECTOR Identity block EN3545-009CPC Number of the basic standard C: Protective cover Type of protective cover P: Plug (free housing) delivered with female attachment system (to cover a receptacle), R: Receptacle (fixed housing) delivered with male attachment system. Type of termination C: With
23、 chain or cable, Without code: without chain or cable. Copyright European Association of Aerospace Industries Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 3545-009:20066 6 Marking 6.1 General Unless there are other s
24、pecific contracted requirements, the marking shall include. 6.2 Marking on the product the manufacturers part number of the housing alone (without the attachment system and without the chain); the date of manufacture (year, week); the manufacturers name or trade mark. 6.3 Marking on the individual p
25、ackaging the EN reference corresponding to the purchasing order (housing with male or female attachment system and with/without chain); the manufacturers part number corresponding to the above EN reference; the date of manufacture (year, week); the manufacturers name or trademark. 7 Technical specification See EN 3545-001. Copyright European Association of Aerospace Industries Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-
