1、 Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data that may improve this document should be sent to: WR-ALC/404 SCMS/GUEEA, Robins AFB GA 31098-1670. Since contact information can change, you may want to verify the currency of this address information usin
2、g the ASSIST Online database at https:/assist.dla.mil . AMSC N/A FSC 6625 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. INCH-POUND A-A-59931 29 July 2013 COMMERCIAL ITEM DESCRIPTION CURRENT-VOLTAGE STANDARD The General Services Administration has authorized the us
3、e of this Commercial Item Description as a replacement for PD13WRGUEEA14, PD10WRGBGBEC29 and PD04WRLEEC03 for all federal agencies. 1. SCOPE. This commercial item description (CID) describes a Current-Voltage Standard, hereinafter referred to as an Electronic Calibrator. The Electronic Calibrator pr
4、ovides accurate reference values of voltage, resistance and current for the calibration of test measurement and diagnostic equipment for the development, repair and maintenance of navigational aids, radio frequency communications equipment and other measurement equipment. This CID lists the minimum
5、performance, design, functional, environmental, reliability requirements and quality assurance provisions for the Electronic Calibrator. 2. CLASSIFICATION. The Electronic Calibrator covered by this CID will be commercially available equipment that has factory installed options and/or may be modified
6、 to the extent necessary to meet the following description. The test set shall be Class 3, in accordance with MIL-PRF-28800, except as specified herein. 3. SALIENT CHARACTERISTICS. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59931 2 3.1 Item
7、Description. The Electronic Calibrator provides five electrical functions; alternating voltage, alternating current, direct voltage, direct current and resistance values. The alternating voltage and current functions have a frequency span from 10 Hz to 1 MHz, the extended bandwidth options extends t
8、he frequency response to 30 MHz. This electrical calibrator is used in the development, repair, calibration and maintenance of test measurement and diagnostic equipment in support of avionics, microwave, navigational aids, radar, satellite and other communications equipment. 3.2 Electrical Calibrato
9、r. The electronic calibrator shall be capable of providing DC voltages with confidence levels as shown in table 1 Voltage Confidence b) meet appropriate performance standards, or c) at a reasonable price. The prime contractor is responsible for ensuring that all subcontractors comply with this requi
10、rement. 5. PRODUCT CONFORMANCE PROVISIONS. 5.1 Contractor certification. The contractor shall certify and maintain substantiating evidence that the product offered meets the salient characteristics of this commercial item description, and the product conforms to the producers engineering drawings, s
11、pecifications, standards, and quality assurance practices. The government reserves the right to require proof of such Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59931 8 conformance prior to first delivery and thereafter as may be otherwise p
12、rovided for under the provisions of the contract. 5.2. Verification. Verification of the delivered Electronic Calibrator will be performed at the delivery point by the end user. 6. PACKAGING. Preservation, packing, and marking shall be as specified in the contract or order. 7. NOTES. 7.1 Source of d
13、ocuments. 7.1.1 Military Specifications, Standards, and Handbooks referenced herein may be obtained online at http:/assist.dla.mil/quicksearch or from the Standardization Documents Order Desk, 700 Robbins Ave, Bldg 4, Section D, Philadelphia, PA 19111-5094. 7.1.2 IEC documents may be obtained online
14、 at http:/www.iec.ch/ or from IEC Regional Centre for North American (IEC-ReCNA) 446 Main Street, 16thFloor, Worcester, MA 01608. 7.1.3 FAR documents may be obtained from the Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954. Electronic copies of the FAR may be obtained online
15、from https:/www.acquisition.gov/far/ . 7.1.4 EIA/ECA documents may be obtained online at http:/ or from IHS Customer Care 15 Inverness Way East, Englewood CO. 80112. 7.1.5 FCC documents may be obtained online at http:/www.ecfr.gov/ or from the Federal Communications Commission 445 12thStreet SW, Was
16、hington DC 20554. 7.1.6 ISO documents may be obtained online at http:/www.iso.org/ or from the American National Standards Institute 1899 L Street NW, 11thFloor US-Washington, DC 20036. 7.2 National Stock Number (NSN). The following NSN corresponds to this CID. The NSN may not be indicative of all p
17、ossible NSNs associated with this CID. (For reference only) NSN: 6625-01-520-5111 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59931 9 7.3 Key words. Alternating Electricity Alternating Potential Direct Electricity Direct Potential Electronic
18、Calibrator Resistance Values NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil/ . Custodians: Preparing Activity: Air Force 84 Air Force 84 Reviewers: Agent: Air Force 99 Air Force 99 (Project 6625-2013-043)Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
