1、MILITARY SPECIF ICATION GROMMET ASSEMBLY 1. SCOPE 1.1 This specification covers requirements, quality assurance provisions, and the preparation for delivery cri- teria for one type of grommet assembly for M422 and M424 proj ectiles. 2. APPLICABLE DOCUMENTS 2.1 The following documents, of the issue i
2、n effect on date of invitation for bids or request for proposals, form a part of this specification to the extent specified herein: STANDARDS MILITARY MIL-STD-105 -0 Saqling Procedures and Tables MIL-STD-1168 0 Lot Numbering of Amunition for Inspection by Attributes DRAWINGS ORDNANCE CORPS 8795677 -
3、 Body 8795678 -o Spacer 8795680 -=-O Grommet Assembly 1 . _ r . -. THIS DOCUMENT 60NTAPNS _6 PAGES. Fsc 1110 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-6-48204 (MU) 8808362 - Packing and Marking for Storage and Shipments 8858986 - Carton, Pa
4、cking, Ammunition, for Band, Protective (Copies of specifications, standards, drawings, and publica- tions required by suppliers in connection with specific pro- curement functions should be obtained from the procuring - activity or.as dkrected by the contracting officer.) 3, REQUIREMENTS 3.1 Materi
5、als. The contractor shall furnish objective evidence (see 6.2) that the material complies with the speci- fications listed on the applicable drawing. all requirements specified on the drawing (dwg) 8795680, with all requirements specified herein, and with the require- ments of all applicable specifi
6、cations to the extent speci- fied on the drawing and herein. 3.2 Assembly. The grommet assembly shall comply with 3.3 Workmanship. 3.3,l Burrs, Parts shall be free from burrs. 3.3.2 Foreim matter. Parts shall be free from chips, dirt, grease, rust, corrosion, or any embedded foreign ma- terial. riou
7、s to any of the parts, nor shall the parts be contami- nated by the cleaning agent. 3.3.3 Cleaning. The cleaning method shall not be inju- 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise spe- cified in the contract or purchase order, the supplier is re- sponsible
8、for the performance of al1 inspection requirements as specified herein. or order, the supplier may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any
9、of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. Except as otherwise specified in the contract 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from
10、IHS-,-,-3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-G-48204 ZZ 7779706 0317472 7 I MIL-G-48204 (MU) Table I Major +Characteristics Sample Sample Sample Sample Lot Size Size Lot Size Size Lot Size Size Lot Size Size 1-16 all 2 8-2 9 23 -52-5
11、6 31 132-156 39 17 16 30-31 24 57-62 32 157-191 40 18 17 32-34 25 63-69 33 192-244 41 19-20 18 35-36 26 70-76 34 245-334 42 21 19 37-40 27 77-86 35 335-519 43 22-23 20 4 1-4 3 28 87-97 36 520-1120 44 98-112 37 over 1120 45 24-25 21 44-47 29 26-27 22 48-51 30 113-133. 38 Table II Minor Characteristic
12、s Sample Sample Sample Sample Lot Size Size Lot Size Size Lot Size Size Lot Size Size 20 21 22 77-121 34-41 17 122-273 1-9 all 14-16 12 28-33 16 12-13 11 23-27 15 55-76 19 10 9 17-18 13 11 10 19-22 14 42-54 18 over 273 4.3.2.1 Classification of characteristics (see 3.2). Cri- tical, major and minor
13、characteristics are defined in MIL-STD- 105. Inspection shall be conducted as follows: 4,3,2.1.1 Spacer (see dwg 8795678, part numbers 8795678 and 8795679) covering details of dwg 8795680. Categories Characteristics MetThod of Inspection Provided by IHSNot for ResaleNo reproduction or networking per
14、mitted without license from IHS-,-,-MIL-G-48204 (MU) Minor 201, Internal diameter . Gage 202. External diameter . Gage 203. Width, min. . Gage 205. Workmanship (see 3.3) Visual/Manual 204, Material (see 3,1) Visual 4.3.2.1.2 Body (see dwg 8795677) covering a detail of dwg 8795680. Categories Charact
15、eristics Method of Inspection Critical: None defined Major: None defined Minor 201. Internal diameter . Gage 202. External diameter . Gage 203. Width, min. . Gage 204. Location of holes . Gage 205. Diameter of holes, max. . Gage 206. Material (see 3.1) Visual 207. Workmanship (see 3.3) Visual/Manual
16、 4.3.2.1.3 Grommet assembly (see dwg 8795680) . Categories Characteristics Method of inspection Critical: . None defined Major 101. Material (see 3.1) Visual Minor 201. Width of cut, max. Gage 202. Presence of proper adhesive . Visual 203. Outside edges feathered . Visual 5 Provided by IHSNot for Re
17、saleNo reproduction or networking permitted without license from IHS-,-,-204. Position of. spacers . Visual 205. Tie in cords Visual 206. Material free of broken surfaces, punc- tures and dents . Visual 207. Staples (5 per spacer) firm and un- damaged. Staple below surface of material on inside diam
18、eters . (alter- , .- * - nate method) i . Visual 208. Workmanship (see 3.3) Visual/Manual 4.3.2.1.4 Cartan, packing, ammunition, for band, protec- tive (see dwg 8858986) and section 5. Categories Characteris tics Method of Inspection Critical: None defined Major 101. Length before packing, min. . *M
19、easure 102, Width before packing, min. *Measure 103. Height before packing, min. . *Measure 105. Properly sealed . Visual 104, Properly packed Visual/Manual Weasurs with suitable scale. Minor 201. Marking legible and correct . Visual 202. Workmanship (see 3.3) Visul/Manual 4.3.2.1.5 Packing and mark
20、ing for storage and shipments (see 8808362) and section 5. Categories Characteris tics Method of Inspection Critical: None defined Major 102. Contents tight in package . Manual 101. Gross load weight . *Measure 103, Correctly packed . Visual/Manual 104. Mat.eria1 (see 3.1) Visual *Determine weight w
21、ith suitable .scale. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-G-48204 (MU) Minor 202 . Workmanship (see 3.3) Visual/Manual 201. Marking, legible and correct Visual 4.3.3 Testing: Not applicable. 4.3.4 Acceptance inspection equipment. 4.3
22、.4.1 4.3.4,2 Minor characteristics and tests. Acceptance in- ritical and maior characteristics and tests. Not applicable. spection equipment for minor characteristics is not specified on ELS . The acceptance inspection equipment, operating in- structions and calibration instructions used by the cont
23、ractor for minor classification inspection shall be approved by the Government representative authorized by the procuring activity. 4.4 Test methods, Not applicable. 5. PREPARATION FOR DELIVERY 5 1 Preservation and packaging. Preservation and packag- ing shall be level A or C, as specified (see 601)
24、. 5.1,1 Level A. The grommet asseuibly shall be packaged in accordance with dwg 8858986 and 8808362, using the speci- fied moisture barrier. 5.1.2 Level C. The grommet assenibly shall be packaged in accordance with dwg 8858986 and 8808362, except that the moisture barrier may be omitted. 5.2 Packing
25、. 5.2.1 Levels A and C. The grommet assembly shall be 5.3 MarkinK. Marking shall be as specified in accordance packed in accordance with dwg 8858986 and 8808362. with dwg 8858986 and 8808362, as applicable. 6. NOTES 6.1 Ordering data. Procurement documents should specify the following: a. b. Title,
26、number and date of this specification. Selection of applicable level of packaging and packing required (see 5.1 and 5.2). 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
