1、- HIL-P-b3312 13 7799906 0397725 5 m .f 5- 37- (9 MIL-P-6 3 3 12 (AR) 29 JUNE 1979 MILITARY SPECIFICATION PRIMER ELECTRIC, M80A1 METAL PARTS FOR (ALTERNATE) This specification is approved for use by the U.S. Army Armament Research and Development Command, and is available for use by all Departments
2、and Agencies of the Department of Defense. 1. SCOPE 1.1 This specification covers the metal parts for an alternate design of Primer, Electric, M80A1. 2. APPLICABLE DOCUMENTS 2.1 The following documents of the issue in effect on date of invitation for bids or request for proposal, form a part of this
3、 specification to the extent specified herein. SPECIFICATIONS MILITARY MIL-A-48078 - Ammunition, Standard Quality Assurance Provision, General Specification For STANDARDS MILITARY MIL-STD-1169 - Packaging, Packing and Marking for Shipment of Inert Ammunition Components FSC: 1390 Beneficial comments
4、(recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Commander, US Army Armament Research and Development Command, Attn. DRDAR-BA, Dover, New Jersey 07801 by using the self-addressed Standardization Document Improvement
5、 Proposal (DD Form 1426) appearing at the end of this document or by letter. / 7 . THIS DOCUMENT CONTAINS 15 PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. , ., MIL-P-b3312 13 77777Ob 0347726 7 = MIL-P-63312 (AR) DRAWINGS ARMY 9327339 - Hea
6、d Primer 9327342 - Plug, Closing 8839509 - Retainer 9327344 - Body 8831022 - Plug I (Copies of specifications, standards, drawings and publications required by suppliers in connection with specific procurement functions should be obtained from the procuring activity or as directed by the contracting
7、 officer). 3. REQUIREMENTS 3.1 Material.-Materi-als shall be in accordance with applicable drawings and specifications. 3.2 Metal parts components.-The metal parts components shall comply with all requirements specified on applicable drawings and with all requirements specified in applicable specifi
8、cations. 3.3 Hydrostatic test.-The primer tubing shall withstand the application of a minimum (min.) hydrostatic pressure with- out rupture or indication of flaws, as evidenced by leaks, and without permanent deformation beyond drawing requirements, when tested as specified in 4.5.1 (see 6,4). sharp
9、 edges, cracks, unblended radii, surface defects, dirt, grease, rust, corrosion products and other foreign matter. The cleaning method shall not be injurious to any part nor shall the parts be contaminated by the cleaning agent. All required markings shall be neat and sharply defined. 3.4 Workmanshi
10、p.-All parts shall be free of burrs, chips, 3.5 First article inspection.-This specification makes provisions for first article inspection. Requirements for submission of first article samples by the contractor shall be as specified in the contract. 2 Provided by IHSNot for ResaleNo reproduction or
11、networking permitted without license from IHS-,-,-MIL-P-b3312 13 W 7797706 03q7727 7 W MIL-P-63312 (AR) 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection and standard quality assurance provisions.-Unless otherwise specified herein or in the contract, the provisions of MIL-A-48078 sha
12、ll apply and are hereby made a part of this detail specification. 4.2 Classification of inspection.-The following types of inspection shall be conducted on this item. a. First Article Inspection b. Quality Conformance Inspection 4.3 First article inspection 4.3.1 Submission.-The contractor shall sub
13、mit a first article sample as designated by the Contracting Officer. first article sample shall consist of ten (10) complete sets of parts (i.e.? ten (10) each of every component). The first article sample shall be evaluated in accordance with the provisions of 4.3.2 and 4.3.3. The 4.3.2 Inspections
14、 to be performed.-See MIL-A-48078, and Table I specified herein. 4.3.3 Rejection.-See MIL-A-48078. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-1 *t *t e e e e e “! h! hl m m m h! ? m m I O rlo O O O rl rl rl rl n w m rn U U al nw wal O rl&l mo
15、miw Co C O Mrl 3u am wn -3 a % 2 4 I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-P-b3312 13 77797Ob 0347727 2 MIL-P-63312 !AR) 4.4 - Quality conformance inspection 4.4.1 Inspection lot formation.-Inspection lots shall comply with7st provisio
16、ns of MIL-A-48078. 4.4.2 Examination.-Unless otherwise specified in the classifica.tion of defects and test tables, sampling plans for major and minor defects shall be in accordance wit$ MIL-STD-105, Inspection Level II. Equipment necessaty for the performance of the inspections listed shall he in a
17、ccordance with 4.4.4, 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-b3312 13 797790b 0347730 7 = o k F! Y I v) c 2 t r h C Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-J MIL-P-63312 13 M
18、7777706 0347733 4 5 I L i 2 - NNN mmm . WNNdN mmmmm . . . O00 00000 5 a, LFI a, 5 u a w 2 Y i Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-63312 13 W 977770b O347934 6 m r Y n U W Z O F 2 k v) 3 u t F G c C r I- c c P alalalal MMMM (d(d(d(d
19、ut3t3u a al C .rl w al a a rl Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- . ._. - . . . . . . . . . ._ . . . MIL-P-63312 13 7977706 03LI3935 8 c Y n Y w c 4: 4: - ti c. a “w O00 O00 TPM N !$? 62* a al d ?-I al u a .rl 1 11 Provided by IHSNot for
20、 ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-633L2 13 W 7773706 0347736 T W n .rl u U 3 LI U (o QI a Id zu $ 8al W Op by Ow w bp 0- QW Op bp bp &? 00000000000 o O00 rlrlrl O00 00000000000 o MO GU sl (o& mo sl .rl Eh pi nu co -u QIsl rlu om AU h a O 9 cm ma QI 1 Q
21、I4 5% 23g 440 coo ao & .- OW UUE LI al u al E (d rl a QI a .d co u 1 O QI rl U .rl u a o *rl u M $ c E k O u G QI k k =1 U h U a QI & al *rl al a c 5 O i! U 2 rl Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-63312 13 W 777770b 03L17937 1 M hl
22、 k N E I u) NNNN(V4-NN mmmmmmmm .i BE au u u .A 13 h (3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-b33L2 13 M 7777706 0347738 3 = I MIL-P-63312 (AR) 4.4.3 Testing.-Testing is described in the First Article and Quality Conformance Inspectio
23、n tables. 4.4.4 Inspection equipment.-The inspection equipment required to perform the inspections and tests prescribed in this specification is identified in the Paragraph Reference/ Inspection Method column in the tables starting with paragraph 4.4.2.1, and the test method paragraphs (see 4.5). Th
24、e contractor shall submit for approval, inspection equipment designs in accordance with the terms of the contract. See Section 6 of MIL-A-48Q78, and Section 6.3 herein. 4.5 Test methods and procedures 4.5.1 Hydrostatic test.-Prior to machining, the primer tubing shall be tested for not less than fiv
25、e seconds at the minimum hydrostatic pressure as calculated by the following formula: p = 1.8 St D Where: P= s= t= D= tests pressure in pounds per square inch (psi) minimum specified yield strength, psi specified minimum wall thickness in inches specified maximum outside diameter in inches 4.5.2 Pro
26、tective coatings.-Procedures for testing, the cleaning of components and the application of protective coatings shall be in accordance with the criteria for testing as specified on the applicable component drawings and in the specification referenced thereon. 5. PREPARATION FOR DELIVERY 5.1 Packagin
27、g, packing and marking.-The parts shall be packaged, packed and marked in accordance with MIL-STD-1169. 6. NOTES 6.1 Intended use.-The components covered by this speci- fication are intended for use in the M80A1 electric primer (alternate). This primer is used on 105MM Cartridges, APDS-T M392 Al, AP
28、DS-T M728 and TPDS-T M724A1. 6.2 Orderinq data.-See MIL-A-48078. 14 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. MIL-P-b3322 23 m 79777Ob 0347737 5 m - MIL-P-63312 (AR) 6.3 Submission of inspection equipment desiqns for approval - (See MIL-A-480
29、78).-Submit equipment designs as required, to Commander, ARRADCOM, ATTN: New Jersey 07801. DRDAR-QAR-I, Dover, 6.4 Hydrostatic test.-If the primer tubing procured for the bodies manufactured in accordance with this specification has been previously subjected to the hydrostatic test specified in this specification, a second hydrostatic test will not be required. Custodian : ARMY -AR Preparing Activity: ARMY -AR Project No.: 1390-A202 15 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
