1、AMSC N/A FSC 5910 DISTRIBUTION STATEMENT A Approved for public release, distribution is unlimited. MIL-PRF-55365/4H SUPERSEDING 26 January 2011 MIL-PRF-55365/4G 23 October 2006 PERFORMANCE SPECIFICATION SHEET CAPACITORS, CHIP, FIXED, TANTALUM, POLARIZED ESTABLISHED RELIABILITY, NON-ESTABLISHED RELIA
2、BILITY, AND HIGH RELIABILITY STYLES CWR06 AND CWR09 This specification is approved for use by all Departments and Agencies of the Department of Defense The requirements for acquiring the product described herein shall consist of this specification and MIL-PRF-55365. FIGURE 1. Style CWR06 (conformall
3、y coated) capacitorsINCH-POUND . Copyright Communications - Electronics Command Provided by IHS under license with CRAINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-55365/4H 2 Case size L .015 (0.38) W .015 (0.38) H .015 (0.38) P .005 (0.13) A .100 (2.54)
4、 .050 (1.27) .050 (1.27) .030 (0.76) B .150 (3.81) .050 (1.27) .050 (1.27) .030 (0.76) C .200 (5.08) .050 (1.27) .050 (1.27) .030 (0.76) D .150 (3.81) .100 (2.54) .050 (1.27) .030 (0.76) E .200 (5.08) .100 (2.54) .050 (1.27) .030 (0.76) F .220 (5.59) .135 (3.43) .070 (1.78) .030 (0.76) G .265 (6.73)
5、 .110 (2.79) .110 (2.79) .050 (1.27) H .285 (7.24) .150 (3.81) .110 (2.79) .050 (1.27) X .273 (6.93) .213 (5.41) .108 (2.74) .047 (1.19) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Metric equivalents are in parentheses. 4. These capacitors are
6、 designed for mounting by dip soldering, thermo-compression bonding, reflow soldering, or other conventional means. 5. Cathode terminal may be epoxy coated on one surface for polarity identification. 6. Solderable surfaces are only those surfaces designated as such. 7. Anode and cathode terminals ma
7、y be two-sided through five-sided, and may not be the same on some designs, but will meet all specification requirements. 8. The anode terminal shall be identified by the riser wire connection, which may extend the case size .015 (0.38 mm) maximum. The riser wire weld area is not solderable. The ris
8、er wire connection shall have a continuous weld of a minimum of 25 percent of the contact surface. 9. When solder coated terminations are required, add an additional .015 (0.38 mm) to the above listed tolerances for “L”, “W”, “H”, and “P” for each case size. FIGURE 1. Style CWR06 (conformally coated
9、) capacitors - Continued. Copyright Communications - Electronics Command Provided by IHS under license with CRAINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-55365/4H 3 FIGURE 2. Style CWR09 molded chip. Figure 3. Style CWR09 molded chip with glue pad. NO
10、TE: At the option of the manufacturer, this configuration with the glue pad between the solderable surfaces may be substituted. Copyright Communications - Electronics Command Provided by IHS under license with CRAINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL
11、-PRF-55365/4H 4 Case size L .015 (0.38) W .015 (0.38) H .015 (0.38) P +.010 (0.25) - .005 (0.13) W2H2min A .100 (2.54) .050 (1.27) .050 (1.27) .030 (0.76) .050 .005 (1.27.013) .030 (0.76) B .150 (3.81) .050 (1.27) .050 (1.27) .030 (0.76) .050 .005 (1.27.013) .030 (0.76) C .200 (5.08) .050 (1.27) .05
12、0 (1.27) .030 (0.76) .050 .005 (1.27.013) .030 (0.76) D .150 (3.81) .100 (2.54) .050 (1.27) .030 (0.76) .095+.005,-.010 (2.41+0.13, -0.25) .030 (0.76) E .200 (5.08) .100 (2.54) .050 (1.27) .030 (0.76) .095+.005,-.010 (2.41+0.13, -0.25) .030 (0.76) F .220 (5.59) .135 (3.43) .070 (1.78) .030 (0.76) .1
13、30.005 (3.300.13) .040 (1.02) G .265 (6.73) .110 (2.79) .110 (2.79) .050 (1.27) .105.005 (2.670.13) .060 (1.52) H .285 (7.24) .150 (3.81) .110 (2.79) .050 (1.27) .145+.005. -.020 (3.68 +0.13, -0.51) .060 (1.52) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general informati
14、on only. 3. Metric equivalents are in parentheses. 4. These capacitors are designed for mounting by dip soldering, thermo-compression bonding, reflow soldering, or other conventional means. 5. The anode (+) terminal shall be identified by a marking on the case. 6. The termination width (W2) shall be
15、 maintained to the top of the solderable area. 7. Solderable surfaces are only those surfaces designated as such. Termination edges are not considered solderable. 8. When solder coated terminations are required, add an additional .015 inch (0.38 mm) to the above listed tolerances for “L”, “W”, “H”,
16、“P”, “W2”, and H2for each case size. FIGURE 2 and 3. Style CWR09 molded chip Continued Copyright Communications - Electronics Command Provided by IHS under license with CRAINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-55365/4H 5 REQUIREMENTS: Dimensions
17、and configuration: See figure 1 and figure 2. Termination finish: In accordance with termination finishes B, C, H, or K of MIL-PRF-55365. DC rated voltage: See table I. Above +85C, voltage derating is required (see MIL-PRF-55365). Operating temperature range: -55C to +125C. Product level designator:
18、 In accordance with MIL-PRF-55365. DC leakage (DCL): See table I. Capacitance: See table I. Capacitance tolerance: 5 percent (J), 10 percent (K), or 20 percent (M). Dissipation factor (DF): See table I. Equivalent series resistance (ESR) at 100 kHz: In accordance with MIL-PRF-55365 (see table I). Re
19、sistance to soldering heat: In accordance with MIL-PRF-55365. * Stability at low and high temperatures: In accordance with MIL-PRF-55365. * Surge voltage: In accordance with MIL-PRF-55365. * Life: * 2,000 hours: In accordance with MIL-PRF-55365 * 10,000 hours: In accordance with MIL-PRF-55365 Solder
20、ability will be in accordance with MIL-PRF-55365 except that following steam aging; test samples may have a 30 minute bake out at 150C prior to solder dipping. Copyright Communications - Electronics Command Provided by IHS under license with CRAINot for ResaleNo reproduction or networking permitted
21、without license from IHS-,-,-MIL-PRF-55365/4H 6 TABLE I. Styles CWR06 and CWR09 characteristics. Part or identifying number (PIN) 1/ 2/ DC rated Cap. DC Leakage (max) Dissipation factor (max) Max ESR 100 kHz Max ESR 100 kHz Case voltage (+85C) (nom) +25C +85C +125C +25C +85C +125C -55C +25C Style CW
22、R06 +25C Style CWR09 size Volts F A A % A % % Ohms Ohms CWR0-C-225- 4 2.2 1.0 10 12 6 8 8 8.0 8.0 A CWR0-C-475- 4 4.7 1.0 10 12 6 8 8 8.0 8.0 B CWR0-C-685- 4 6.8 1.0 10 12 6 8 8 5.5 5.5 C CWR0-C-106- 4 10.0 1.0 10 12 8 8 10 4.0 4.0 D CWR0-C-156- 4 15.0 1.0 10 12 8 10 12 3.5 3.5 E CWR0-C-336- 4 33.0
23、2.0 20 24 8 10 12 2.2 2.2 F CWR0-C-686- 4 68.0 3.0 30 36 10 12 12 1.1 1.1 G CWR0-C-107- 4 100.0 4.0 40 48 10 12 12 .9 .9 H CWR0-D-155- 6 1.5 1.0 10 12 6 8 8 8.0 8.0 A CWR0-D-335- 6 3.3 1.0 10 12 6 8 8 8.0 8.0 B CWR0-D-475- 6 4.7 1.0 10 12 6 8 8 5.5 5.5 C CWR0-D-685- 6 6.8 1.0 10 12 6 8 8 4.5 4.5 D C
24、WR0-D-106- 6 10.0 1.0 10 12 8 10 12 3.5 3.5 E CWR0-D-226- 6 22.0 2.0 20 24 8 10 12 2.2 2.2 F CWR0-D-476- 6 47.0 3.0 30 36 10 12 12 1.1 1.1 G CWR0-D-686- 6 68.0 4.0 40 48 10 12 12 .9 .9 H CWR0-F-105- 10 1.0 1.0 10 12 6 8 8 12.0 10.0 A CWR0-F-225- 10 2.2 1.0 10 12 6 8 8 8.0 8.0 B CWR0-F-335- 10 3.3 1.
25、0 10 12 6 8 8 5.5 5.5 C CWR0-F-475- 10 4.7 1.0 10 12 6 8 8 4.5 4.5 D CWR0-F-685- 10 6.8 1.0 10 12 6 8 8 3.5 3.5 E CWR0-F-156- 10 15.0 2.0 20 24 8 8 10 2.5 2.5 F CWR0-F-336- 10 33.0 3.0 30 36 10 12 12 1.1 1.1 G CWR0-F-476- 10 47.0 5.0 50 60 10 12 12 .9 .9 H CWR0-H-684- 15 .68 1.0 10 12 6 8 8 12.0 12.
26、0 A CWR0-H-155- 15 1.5 1.0 10 12 6 8 8 8.0 8.0 B CWR0-H-225- 15 2.2 1.0 10 12 6 8 8 5.5 5.5 C CWR0-H-335- 15 3.3 1.0 10 12 6 8 8 5.0 5.0 D CWR0-H-475- 15 4.7 1.0 10 12 6 8 8 4.0 4.0 E CWR0-H-106- 15 10.0 2.0 20 24 6 8 8 2.5 2.5 F CWR0-H-226- 15 22.0 4.0 40 48 6 8 8 1.1 1.1 G CWR0-H-336- 15 33.0 5.0
27、50 60 8 8 10 .9 .9 H CWR0-J-474- 20 .47 1.0 10 12 8 8 10 16.0 14.0 A CWR0-J-684- 20 .68 1.0 10 12 6 8 8 14.0 10.0 B See footnotes at the end of table Copyright Communications - Electronics Command Provided by IHS under license with CRAINot for ResaleNo reproduction or networking permitted without li
28、cense from IHS-,-,-MIL-PRF-55365/4H 7 TABLE I. Styles CWR06 and CWR09 characteristics- Continued. PIN DC rated Cap. DC Leakage (max) Dissipation factor (max) Max ESR 100 kHz Max ESR 100 kHz Case 1/ 2/ voltage (+85C) (nom) +25C +85C +125C +25C +85C +125C -55C +25C Style CWR06 +25C Style CWR09 size Vo
29、lts F A A % A % % Ohms Ohms CWR0-J-105- 20 1.0 1.0 10 12 6 8 8 12.0 12.0 B CWR0-J-155- 20 1.5 1.0 10 12 6 8 8 6.0 6.0 C CWR0-J-225- 20 2.2 1.0 10 12 6 8 8 5.0 5.0 D CWR0-J-335- 20 3.3 1.0 10 12 6 8 8 4.0 4.0 E CWR0-J-685- 20 6.8 2.0 20 24 6 8 8 2.4 2.4 F CWR0-J-156- 20 15.0 3.0 30 36 6 8 8 1.1 1.1 G
30、 CWR0-J-226- 20 22.0 4.0 40 48 6 8 8 .9 .9 H CWR0-K-334- 25 .33 1.0 10 12 6 8 8 15.0 15.0 A CWR0-K-684- 25 .68 1.0 10 12 6 8 8 10.0 7.5 B CWR0-K-105- 25 1.0 1.0 10 12 6 8 8 6.5 6.5 C CWR0-K-155- 25 1.5 1.0 10 12 6 8 8 6.5 6.5 D CWR0-K-225- 25 2.2 1.0 10 12 6 8 8 3.5 3.5 E CWR0-K-475- 25 4.7 2.0 20 2
31、4 6 8 8 2.5 2.5 F CWR0-K-685- 25 6.8 2.0 20 24 6 8 8 1.2 1.2 G CWR0-K-106- 25 10.0 3.0 30 36 6 8 8 1.4 1.4 G CWR0-K-156- 25 15.0 4.0 40 48 6 8 8 1.0 1.0 H CWR0-M-224- 35 .22 1.0 10 12 6 8 8 24.0 18.0 A CWR0-M-474- 35 .47 1.0 10 12 6 8 8 17.0 10.0 B CWR0-M-684- 35 .68 1.0 10 12 6 8 8 10.0 8.0 C CWR0-
32、M-105- 35 1.0 1.0 10 12 6 8 8 6.5 6.5 D CWR0-M-155- 35 1.5 1.0 10 12 6 8 8 4.5 4.5 E CWR0-M-335- 35 3.3 1.0 10 12 6 8 8 2.5 2.5 F CWR0-M-475- 35 4.7 2.0 20 24 6 8 8 1.5 1.5 G CWR0-M-685- 35 6.8 3.0 30 36 6 8 8 1.3 1.3 H CWR0-N-104- 50 .10 1.0 10 12 6 8 8 22.0 22.0 A CWR0-N-154- 50 .15 1.0 10 12 6 8
33、8 25.0 17.0 A CWR0-N-224- 50 .22 1.0 10 12 6 8 8 17.0 14.0 B CWR0-N-334- 50 .33 1.0 10 12 6 8 8 12.0 12.0 B CWR0-N-474- 50 .47 1.0 10 12 6 8 8 8.0 8.0 C CWR0-N-684- 50 .68 1.0 10 12 6 8 8 7.0 7.0 D CWR0-N-105- 50 1.0 1.0 10 12 6 8 8 6.0 6.0 E CWR0-N-155- 50 1.5 1.0 10 12 6 8 8 4.0 4.0 F CWR0-N-225-
34、50 2.2 2.0 20 24 6 8 8 2.5 2.5 F CWR0-N-335- 50 3.3 2.0 20 24 6 8 8 2.0 2.0 G CWR0-N-475- 50 4.7 3.0 30 36 6 8 8 1.5 1.5 H 1/ Complete PIN shall include additional symbols to indicate style, termination finish, capacitance tolerance, product level designator, and, if applicable, surge current option
35、 letter. If optional surge current is not required, the last “-“ shall be deleted. 2/ Styles CWR06 and CWR09 are, with the acquiring agency approval, considered to be interchangeable, provided the size, capacitance, capacitance tolerance, failure rate level, rated voltage, maximum ESR value, and sur
36、ge current option (if applicable) remain the same. Copyright Communications - Electronics Command Provided by IHS under license with CRAINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-55365/4H 8 NOTES: Reference documents. This specification sheet referenc
37、es the following document. MIL-PRF-55365 (Copies of this document is available online at https:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094). Changes from previous issue. The margins of this specification are marke
38、d with asterisks to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on t
39、he entire content irrespective of the marginal notations and relationship to the last previous issue. Custodians: Preparing activity: Army - CR Army - CR Navy - EC Air Force - 85 Agent: DLA - CC DLA - CC Review activities: (Project 5910-2011-002) Army - AR, MI Navy - AS, MC, OS, SH Air Force 19, 99
40、NASA - NA NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil/ . Copyright Communications - Electronics Command Provided by IHS under license with CRAINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
