1、i NOT MEASUREMENT SENSITIVE 1 MIL-T-62059B(AT) 11 SUPERSEDING SeDtemher 1991 MIL-T-62059A(AT) E March 1982 MILITARY SPECIFICATION TRAILER, CARGO: WITIY HYDRAULIC Lrm BODY, 2,000 FOUND PAYWAD, 2 WHEEL, COMMERCIAL This specification is approved fur use by the US Army Tank- Automotive Command, Degwimen
2、t of 1.e Army, and is available for - use by all Departments and Agencies of %he Department of Defense. 1. SCOPE 1.1 SC ODE. This specification covers a two-wheel comercial, hydraulic lift cargo type trailer having a minimum load carrying capacity of 2,000 oncia iincier 1ior.ni1 operat ag coiidit io
3、ns. specification are commercial items which are warranted by the manufacturer as specified in acquisition documents. TmilerB procured under this 2. APPLICABLE I30CUMENTS 0 2.1 Governuwua. . The following 0 2.1.1 Spmflcatinna. nteds and h- specifications, standards and handbooks form a part of this
4、document to the extent specified herein- documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) , and supplement thereto, cited in the solicitation (see 6.2). Unlesa otherwise specified, the issues of these (recommendations, additions, del
5、etions) and any pertinent data which may be of use in improving this document should be addressed to: US Army Tank-Automotive Command, ATTN: AMSTA-UED, Warren, MI Document Improvement Proposal (DD Form 1426) appearing at the end of this dociunent or by letter. 48397-5000, by using the self-addressed
6、 Standardization I I AMCC N/A Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-b2059B 23 999990b 0493504 9 Vehir, les. MILITARY MIL-STD-1223 - Non-Tactical Wheeled Vehicles Treatment, Painting, Identification Marking and Data Plate Standards. ST
7、APJDARDS FEDERAL * FED-STD-297 - Rustproofing of Commercial (Non-tactical) * (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Naval Publications and Forms Center, Military Specifications and Standards, ldg. 4D, 700 Robbins Av
8、enue, Philadelphia, PA 19111-5094.) * 2.1.2 Wer Gover-tfi. dr-s. and mbLjcatiom . The following other Government docimenta, drawings, and publications form a part of this dociment to the extent specified herein. the issues are those cited in the solicitation- Unless otherwise specified, % DEPARTMENT
9、 OF DEFENSE Department of Defense Index of Specifications and Standards (DODISS). (Copies of the WDISS are available an a yearly subscription basis either from the Government Printing Office for hard copy, or microfiche copies are available from the Director, Navy Publication and Printing Service Of
10、fice, 700 Robbins Avenue, Philadelphia, PA 19111-5093.) DEPARTMENT OF TRANSWRTATION (DOT) Federal Motor Carrier Safety Regulations. Federal Motor Vehicle Safety Standards - % Federal Regulations, 49 CFR, and the Federal Register and should be addressed to the Superintendent of Documents, U.S. Govern
11、ment Printing Office, Flashington, D-C- 20402.) (Application for copies of DOT publications should reference the code of * 2.2 Nnii - Goverment T?- The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are D
12、oD adopted are those listed in the issue of the DODISS cited in the solicitation. the issues of documenta not listed in the WDISS are the issues of the documents cited in the aolicitation (see 6.2). Unless otherwise specified, X THE EUROPEAN TIRE AND RIM TECHNICAL ORGANISATION (ETRTO) Standards Manu
13、al (Application for copies of the ETRTO publications should be addressed to the European Tyre and Rim Technical Organisation, 32, Avenue Brugrnami, 1060 Brussels, Belgium.) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- I MIL-T-620598 23 9979906
14、OY73505 O - MI L-T-62059B i AT ) SAE, INC. CAE Standards and Recommended Practices. , J580 - Seven-knductor Electrical Connector for Truck-Trailer Jumper Cable. 5588 - Turn Signal tamps. J682 51067 - Rear Wheel Splash and Stone Throw - Seven-Conductor Jacketed Cable for Truck and Protection. Trailer
15、 Connections. (Application for copies of CAE publications should be addressed to SAE, Inc - , 400 Commonwealth Drive , Warrendale , PA 15096 - ) THE TIRE AND RIM ASSOCIATION, INC. Year Book, * be addressed to the Tire and Rim Association Inc., 175 Montrose West Ave., Copley, OH 44321.) * from the or
16、ganizations that prepare or distribute the documents. documents also may be available in or through libraries or other informational services.) % 2.3 Qrdar of wecea. In the event of a conflict between the text of this document and the references cited herein, the text of this document shall take pre
17、cedence. applicable laws and regulationsunless a specific exemption has been obtained. (Application for copies of Tire and Rim Association publication8 should (Non-Government standards and other publications are normally available These Nothing in this document, however, supersedes 3. REQUIREMENTS *
18、 3.1 Standard vehicle and accessorh - Except as specified in 3.1.1 through 3-1-1-4, the vehicle, components, assemblies, and accessories to be delivered under the contract shall be the manufacturers standard or optional items, which meet or exceed the requirements of this specification. vehicle item
19、s shall be as represented and rated in the manufacturers technical data. equipment manufacturers technical data. specifications and technical material identical to that furnished to the authorized company representatives for selection of vehicle models and components, and shall be on file in the eng
20、ineering offices of the procuring activity, prior to delivery of the items. components specified in 3.1, the vehicle shall be furnished with special equipment as specified herein. All Special or mounted equipment shall be as represented in the Technical data shall be limited to 3.1.1 Smcial reau- -
21、In addition to the standard vehicle and 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-62059B 23 7999906 0493506 2 C MIL-T-62059B ( AT) The vehicle shall be treated and I. * 3.1.1.1 painted in accordance with MIL-STD-1223. activity for the a
22、ppropriate service (see 6.2), the exterior color shall be in accordance with MIL-STD-1223. As specified by the procuring * 3.1.1.2. - As specified by the procuring activity for the appropriate military service (see 6-21, identification marking and data plates shall be in accordance with MIL-STD-1223
23、. When specified (see G.2), concealed markings shall be furnished. * 3.1.1.3 Ewirea . The trailer shall be equipped with single wheels and tires. and Rim Association or European Tyre and Rim Technical Organisation recommendacions for the type and size of tires furnished. type tires are specified in
24、acquisition documents, multi-piece rims shall not be furnished. Tire and rim sizes shall be the same for all wheels on the vehicle - The rim size and tire ratings shall conform to Tire Except when tube * 3.8.1 W. Steel belted radial tires shall be furnished. Tires shall be tobeless truck type with h
25、ighway tread. capacity at least equal to the load imposed on each tire, measured at each wheel, at the ground, with the trailer fully loaded with specified payload. Tires shall conform to the Tire and Rim Association or to the European Tyre and Rim Technical Organisation recommendations. Tires shall
26、 be of the rated 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-P Y MIL-T-b2059B 23 W 999990b 0493509 W MIL-T-62059B(AT) 3-8.2 l2,parFi wheel or r im- When specified (see .S), a spare wheel or rim shall be furnished. 3.8.3 When specified (see 6-2)
27、, an inflated spare tire mounted on the spare wheel or rim shall be furnished. shall be of the same size, tread design and ply rating as the tires furnished on the trailer. * 3.8.4 Gamier for Rwre tire asRemm - When specified (see 6.2), a carrier for a spare wheel or rim and tire assembly shall be i
28、nstalled in a readily accessible location on the vehicle. Threaded fasteners, when used to secure the spare tire in the carrier, shall be constructed of or plated with corrosion-resistant material. mounting of a spare wheel assembly using only the tools specified in 3.8.5, The carrier shall enable t
29、he safe removal and installation of the spare tire assembly from and to the vehicle and carrier without personnel positioning themselves or any part of their body under the spare tire assembly. The spare tire Carrier design shall enable safe removal or 3.8-5 Toola. When specified (see 6.S), the vehi
30、cle shall be furnished with tools required for exchanging mounted tire assembly with the spare assembly, and shall include at least a jack, jack handle and wheelnut wrench. under axle, or other satisfactory lift point, at any wheel with the tire flat. the loaded vehicle to a height adequate to permi
31、t removal and replacement of the wheel and tire assembly. The jack shall be of such closed height as to permit its location The jack, without blocking, shall be capable of raising any wheel of 3.9 Pervice br- . Unless inertia brakes are specified (see 3.9.1), Brake the trailer shall be equipped with
32、 a 12-volt electric brake system. linings shall be of nonasbeatos material. controller kit; for mounting on the dash of the towing vehicle, a controller kit for synchronizing the trailer electric brakes with the brakes of the towing vehicle, and an emergency breakaway kit- all necessary parts (excep
33、t storage battery for breakaway kit) and installation instructions. Unless otherwise specified, the synchronizing controller shall be for use with hydraulic brake equipped towing vehicles. When specified (see 6.2), the synchronizing controller shall be for use with air brake equipped towing vehicles
34、. The kits shall be boxed, marked as to contents and securely attached to the trailer for shipment. The system shall include a manual Kits shall be complete with 3.9.1 Inertia hrakeq . When specified (see 6.2), the trailer shall be furnished with an inertia (surge) applied hydraulic brake system in
35、lieu of electric brakes. The inertia brake actuator, mounted on the tow bar, shall include a master cylinder, an accumulator chamber and a hold-off spring to prevent brake applications due to road shock or trailer pitching. The system shall provide for modulated brake applications, shall be protecte
36、d against; the entrance of foreign matter, shall include breakaway features conforming to Federa3 Motor Carrier Safety Regulation 393.43(d), an shall enable the trailer to be backed up without continued application of the trailer brakes. 7 Provided by IHSNot for ResaleNo reproduction or networking p
37、ermitted without license from IHS-,-,-s=7?s MIL-T-b2059B 23 999990b 0493530 4 I 5 3.9.2 . Manually applied parking brakes shall be furnished. Regulation 393.41. corrosion-resistant steel- Lubrication fittings shall be provided. Parking brakes shall conform to Federal Motor Carrier Safety When brake
38、cables are used, the cables shall be Provisions shall be made for slack adjustment. 3.10 Caunlina device arid tow inflation of all tires; and complete lubric_ation of chassis, and running gear with grades of lubricants recommended for the ambient air temperature at the delivery point. 0 cryeratianal
39、 use ludint the following: adjustment of the brake .I 3.18 Florkmanshili . Defective components or parts and assemblies which have been repaired or modified to overcome deficiencies shall not be furnished. Welded, bolted, and riveted construction utilized shall be in accordance with the highest stan
40、dards of the industry. 4. QUALITY ASSUFANCE PROVISIONS Unless otherwise specified in the . * 4.1 -tv forinsnection contract, the contractor is responsible for the performance of all inspection requirements (examination and tests) as specified herein. otherwise specified in the contract, the contract
41、or may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessar
42、y to assure supplies and services conform to prescribed requirements. . All items must meet all * 4.1.1 -tv for nnmplianne requirements of sections 3 and 5. specification shall become a part of the contractors overall inspection 0 system or quality program. The absence of any inspection requirements
43、 in the specification shall not relieve the contractor of the responsibility for ensuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract. inspection, as part of manufacturing operations, is an acceptable practice to ascertain con
44、formance requirements, however, this does not authorize submission of known defective material, either indicated or actual, nor do49 it commit the Government to acceptance of defective material. 4.2 Gnvernment verification - Quality assurance operations performed by Except as I. The inspection set f
45、orth in this Sampling a1 the contractor will be subject to Government verification at unscheduled intervals. determine that practices, methods, and procedures of the contractors inspection are being properly applied. correct product deficiencies discovered shall be cause for suspension of acceptance
46、 until correction has-been made or until conformance of product to specification criteria has been demonstrated. 4.3 First Froduction vehicle insDection . The first vehicle produced under the contract shall be inspected by the contractor at his plant under the direction and in the presence of Govern
47、ment representatives. Verification will consist of observation of the operations to Failure of the contractor to promptly The purpose 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-F MIL-T-62059B 23 W 9999906 0493534 3 W D MIL-T-62059B( AT) of th
48、e inspection shall be to determine vehicle conformity with the contract. Acceptance of the first production vehicle shall not constitute a waiver by the Government of its rights under the provisions of the contract. 4.3.1 Wie Wei turning ability shall be observed to verify conformance to 3.3.2. Afte
49、r the test the trailer shall be examined for evidence of misalinement, binding or other malfunction. At least five sudden stops shall be made from a speed of Tracking ability shall be observed to verify 4.3.3 Test faib - The vehicle shall successfully complete the entire Failure of the vehicle to successfully complete the test shall be test. cause for nonacceptance of any of the contract quantity, pending correction of deficiencies and evi
