1、 Intentionally left blank AN AMERICAN NATIONAL STANDARDFRAMING-AFFIXED SUPPORTS FOR OFF-THE-FLOOR WATERCLOSETS WITH CONCEALED TANKSASME A112.6.2-2000 EDITIONDate of Issuance: December 29, 2000This Standard will be revised when the Society approves the issuance ofa new edition. There will be no adden
2、da or written interpretations of therequirements of this Standard issued to this edition.ASME is the registered trademark of The American Society of Mechanical Engineers.This code or standard was developed under procedures accredited as meeting the criteria forAmerican National Standards. The Standa
3、rds Committee that approved the code or standardwas balanced to assure that individuals from competent and concerned interests have had anopportunity to participate. The proposed code or standard was made available for public reviewand comment that provides an opportunity for additional public input
4、 from industry, academia,regulatory agencies, and the public-at-large.ASME does not “approve,” “rate,” or “endorse” any item, construction, proprietary device,or activity.ASME does not take any position with respect to the validity of any patent rights asserted inconnection with any items mentioned
5、in this document, and does not undertake to insure anyoneutilizing a standard against liability for infringement of any applicable letters patent, nor assumeany such liability. Users of a code or standard are expressly advised that determination of thevalidity of any such patent rights, and the risk
6、 of infringement of such rights, is entirely theirown responsibility.Participation by federal agency representative(s) or person(s) affiliated with industry is not tobe interpreted as government or industry endorsement of this code or standard.ASME accepts responsibility for only those interpretatio
7、ns of this document issued inaccordance with the established ASME procedures and policies, which precludes the issuanceof interpretations by individuals.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the p
8、ublisher.The American Society of Mechanical EngineersThree Park Avenue, New York, NY 10016-5990Copyright 2000 byTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERSAll Rights ReservedPrinted in U.S.A.FOREWORDIn 1990, the American Society of Mechanical Engineers was solicited to develop astandard for carrier
9、s that are used in frame construction. At the time, a standard existedfor the evaluation of carriers for floor-affixed carriers and supports that are typically installedin commercial, industrial, and institutional buildings with concrete floors. The standard forfloor-supported carriers and supports
10、is ASME A112.6.1M.This Standard complements ASME A112.6.1M. Some of the specifications and tests aresimilar and appropriately, are referenced in this Standard. However, due to differences inassembly of these framing-affixed products from the floor-affixed products, some criteriaare different.The bas
11、is for this Standard was an Interim Guide Criteria document prepared by theInternational Association of Plumbing and Mechanical Officials (IAPMO).Suggestions for improvement of this Standard are welcome. They should be sent to TheAmerican Society of Mechanical Engineers; Attn: Secretary, A112 Main C
12、ommittee; ThreePark Avenue; New York, NY 10016.This Edition was approved as an American National Standard on October 18, 2000.iiiIntentionally left blank ASME STANDARDS COMMITTEE A112Standardization of Plumbing Materials and Equipment(The following is the roster of the Committee at the time of appro
13、val of this Standard.)OFFICERSP. J. Higgins, ChairJ. A. Ballanco, Vice ChairC. J. Gomez, SecretaryCOMMITTEE PERSONNELR. H. Ackroyd, ConsultantJ. A. Ballanco, JB Engineering & Code ConsultingS. L. Cavanaugh, California State Pipe TradesA. Cohen, Arthur Cohen & AssociatesP. V. DeMarco, American Standa
14、rd, Inc.G. S. Duren, Code Compliance, Inc.F. C. Evans, Zin-Plas CorporationL. S. Galowin, National Institute of Standards and TechnologyC. J. Gomez, The American Society of Mechanical EngineersR. I. Greenwald, Sunroc CorporationE. Grunewald, Association of Home Appliance ManufacturersP. J. Higgins,
15、PJ Higgins & Associates, Inc.D. E. Holloway, United States Testing Co., Inc.M. Klimboff, ConsutantR. M. Martin, California Energy CommissionS. Moinian, Moen, Inc.R. E. Pamplona, U.S. Naval Naval Construction Battalion CenterS. Rawalpindiwala, IAPMOS. Remedios, Delta Faucet Co.J. A. Sargent, Kohler C
16、o.D. W. Viola, BOCA InternationalR. E. White, ConsultantPERSONNEL OF PANEL 6 DRAINAGE PRODUCTSS. J. McDanal, Chair, Jay R. Smith Manufacturing Co.R. H. Ackroyd, Vice Chair, ConsultantP. J. Higgins, Secretary, PJ Higgins & Associates, Inc.J. A. Ballanco, JB Engineering & Code ConsultingA. R. Becker,
17、Zurn Industries, Inc.A. Cohen, Arthur Cohen & AssociatesG. J. Flegel, Flegel Consulting Services, Inc.M. W. Marshall, Tyler PipeS. Rawalpindiwala, IAPMOJ. A. Sargent, Kohler Co.G. E. Shillington, Briggs Industries, Inc.R. C. Smith, United States Testing Co., Inc.W. M. Smith, Jay R. Smith Manufacturi
18、ng Co.D. W. Viola, BOCA InternationalR. E. White, ConsultantvPERSONNEL OF WORKING GROUP 2 CARRIERSAND SUPPORTS FOR PRIVATE USES. J. McDanal, Chair, Jay R. Smith Manufacturing Co.R. H. Ackroyd, Vice Chair, ConsultantP. J. Higgins, Secretary, PJ Higgins & Associates, Inc.A. R. Becker, Zurn Industries,
19、 Inc.P. V. DeMarco, American Standard, Inc.J. A. Sargent, Kohler Co.D. W. Viola, BOCA InternationalR. E. White, ConsultantM. Wolpert, Geberit Manufacturing, Inc.viCONTENTSForeword iiiCommittee Roster v1 General . 11.1 1Scope .1.2 1Units of Measurement .1.3 1References 1.4 1Definitions 2 Materials an
20、d Finishes 13 Requirements 13.1 1General .3.2 2Strength and Deflection 3.3 2Waste Fittings .3.4 2Special Fixtures .3.5 2Faceplates .3.6 3Foot Supports .3.7 3Installation Instructions .4 Test Requirements 34.1 3Waste Fittings .4.2 3Load Test .5 Marking 3Figures1 Framing-Affixed Support With Concealed
21、 Tank 22 Load Test on Wall-Hung Water Closet 3viiIntentionally left blank ASME A112.6.2-2000 EDITIONFRAMING-AFFIXED SUPPORTS FOROFF-THE-FLOOR WATER CLOSETS WITH CONCEALED TANKS1 GENERAL1.1 ScopeThis Standard establishes minimum performance re-quirements for framing-affixed supports for off-the-floor
22、water closets with concealed tanks. It is not intendedto limit the use of other materials, finishes, and designsthat equal or exceed the requirements of this Standard.1.2 Units of MeasurementValues are stated in U.S. Customary units and theInternational System of Units (SI). The U.S. Customaryunits
23、shall be considered as the standard.1.3 ReferencesThe following documents form a part of this Standardto the extent specified herein. The latest issue shallapply.ASME A112.6.1M, Floor-Affixed Supports for Off-the-Floor Plumbing Fixtures for Public UseASME A112.19.2M, Vitreous China Plumbing Fixtures
24、Publisher: The American Society of Mechanical Engi-neers (ASME), Three Park Avenue, New York, NY10016-5990ANSI/ASSE 1002, Water Closet Flush Tank Fill ValvePublisher: American Society of Sanitary Engineering(ASSE), 28901 Clemens Road, Westlake, OH 441451.4 DefinitionsA number of special terms, which
25、 are specific tothe supports described by this Standard, are definedherein. For additional terms pertinent to support andcarrier nomenclature, see ASME A112.6.1M.carrier: a concealed support for an off-the-bination water closet support and fitting: an as-sembly for supporting off-the-floor water clo
26、sets, which1includes both support- and waste-fitting componentsand a concealed flush tank. See Fig. 1.fitting(s): the sanitary waste-fitting component(s) of acombination water closet support and fitting.fixture bolts: the bolts on which the fixture is mounted,and which connect directly to the carrie
27、r.foot: a member of a carrier, designed to rest on thefloor in a concealed location to anchor and supportthe assembly.gasket, fixture: the scaling element between fixtureand fittings.integral tank: a flush tank that is provided as anoption to the support assembly for the purpose offlushing the wall-
28、hung fixture, which is usually con-cealed behind the finished wall.off-the-floor fixture: any sanitary plumbing fixture,located adjacent to a wall (partition), which has novisible contact with the floor in front of the wall.2 MATERIALS AND FINISHESMaterials and finishes used in supports and carriera
29、ssemblies shall conform to the material requirementsas cited in ASME A112.6.1M. Waste fittings shall beof cast iron, bronze, plastic, or other materials capableof withstanding the pressure testing in section 4.3 REQUIREMENTS3.1 GeneralOff-the-floor framing-affixed supports for water clos-ets shall c
30、onsist of an integral tank, a supply pipe tothe water closet, a waste fitting from the water closet,and support assembly. The support assembly shall incor-porate as a minimum a support structure complete withfasteners to mount and connect the fixture, fitting, andpiping to carry the waste from the f
31、ixture into thewaste line, means to affix the assembly to the structuralfloor or wall, and any necessary gaskets to connectFRAMING-AFFIXED SUPPORTS FOROFF-THE-FLOOR WATER CLOSETS WITH CONCEALED TANKSASME A112.6.2-2000 EDITIONConcealed tankFlush pipeWasherStudDischarge elbowSupport memberFront View S
32、ide ViewSupport framingFIG. 1 FRAMING-AFFIXED SUPPORT WITH CONCEALED TANKassembly components. Materials and finishes shall bein accordance with the applicable requirements of sec-tion 2.3.2 Strength and DeflectionThe carrier shall be designed so that the completeinstalled assembly shall be rigid and
33、 of sufficientstrength to accept a load of 500 lb (225 kg) locatedat the front edge of the fixture. The assembly shallwithstand this loading without failure, permanent distor-tion, or excessive deflection when the system assemblyis rigidly secured, when tested in accordance withsection 4.3.3 Waste F
34、ittingsWaste fittings shall be of sanitary design with noobstructions, protuberances, or other irregularities inthe flow passageways that can cause a build-up ofsolids or a stoppage, or restrict the flow of wastematerial. Changes in direction shall be designed todeflect flow into the waste line with
35、 as little turbulenceas possible and generally in accord with plumbingwaste and vent fitting practice. All flow passages shall2pass solids at least as large as those that can passthrough the connected fixture. See ASME A112.19.2Mfor water closet trap dimensions. Venting size shall bein accordance wi
36、th accepted engineering practice asdefined in the model plumbing codes for water closets.The inlet to the waste fitting shall accommodate theoutlet of a two-bolt-mounted water closet outlet.3.4 Special FixturesWater closet supports shall be permitted to beequipped with an optional integral flush tan
37、k. The flushtank shall be equipped with a ball cock complyingwith ANSI/ASSE 1002.3.5 FaceplatesWhen provided, faceplates shall be of material de-signed to provide the necessary strength and rigidityas outlined in paras. 3.1 and 3.2. On vertically adjustableunits, the faceplate shall provide a watert
38、ight seal atits joint with the fitting to withstand a hydrostatic testpressure of 30 psig (207 kPa gauge).FRAMING-AFFIXED SUPPORTS FOROFF-THE-FLOOR WATER CLOSETS WITH CONCEALED TANKS ASME A112.6.2-2000 EDITIONApplied loadMeasuring deviceStructural wall permanufacturers instructionsFIG. 2 LOAD TEST O
39、N WALL-HUNG WATER CLOSET3.6 Foot SupportsWhen provided, foot support members shall be capa-ble of extending downward from the support to contactthe floor or other framing structure to provide addedsupport.3.7 Installation InstructionsManufacturers shall provide complete installation re-quirements ne
40、cessary to support the fixture consistentwith the performance requirements of this Standard.4 TEST REQUIREMENTS4.1 Waste Fittings4.1.1 Test Method. The waste fittings shall beassembled and all but one end capped. One end ofthe assembly shall be assembled to an air pressuredevice capable of achieving
41、 pressures from 010 psig(069 kPa gauge).34.1.2 Performance Requirements. Waste fittingsshall withstand an air pressure of 5 psig (35 kPa gauge)for one minute without leakage.4.2 Load Test (See Fig. 2)4.2.1 Test Method. The support shall be affixedto framing members in accordance with manufacturersin
42、structions. The fixture shall be assembled to thesupport. The elevation of the top edge of the fixtureat its outermost edge shall be recorded. A 500 lb (225kg) load shall be placed on the front edge of the fixturefor a period of 5 minutes. After placement of the load,the top edge shall be measured a
43、gain. After removalof the load, the elevation shall be measured again.4.2.2 Performance Requirements. The supportshall not deflect greater than 0.250 in. (6.3 mm) duringthe application of the load. The fixture shall return towithin 0.125 in. (3.1 mm) of the first measurementupon removal of the load.
44、5 MARKINGSupports shall be marked with the manufacturersname or trademark and ASME A112.6.2.Intentionally left blank ASME STANDARDS RELATED TO PLUMBINGAir Gaps in Plumbing Systems A112.1.2-1991(R1998)Air Gap Fittings for Use With Plumbing Fixtures, Appliances, and AppurtenancesA112.1.3-2000Performan
45、ce Standard and Installation Procedures forStainless Steel Drainage Systems for Sanitary, Storm, andChemical Applications, Above and Below Ground .A112.3.1-1993Water Heater Relief Valve Drain Tubes A112.4.1-1993(R1998)Plastic Fittings for Connecting Water Closets to theSanitary Drainage System A112.
46、4.3-1999Floor-Affixed Supports for Off-the-Floor Plumbing Fixtures forPublic UseA112.6.1M-1997Framing-Affixed Supports for Off-the-Floor Water Closets WithConcealed Tanks .A112.6.2-2000Backwater Valves A112.14.1-1975(R1998)Plumbing Fixture Fittings . A112.18.1-2000Performance Requirements for Backfl
47、ow Protection Devicesand Systems in Plumbing Fixture Fittings A112.18.3M-1996Flexible Water Connectors .A112.18.6M-1999Deck Mounted Bath/Shower Transfer ValvesWith Integral Backflow Protection . A112.18.7-1999Enameled Cast Iron Plumbing Fixtures .A112.19.1M-1994(R1999)Vitreous China Plumbing Fixture
48、s A112.19.2M-1998Stainless Steel Plumbing Fixtures (Designed forResidential Use) .A112.19.3M-1987(R1996)Porcelain Enameled Formed Steel Plumbing Fixtures.A112.19.4M-1994(R1999)Trim for Water-Closet Bowls, Tanks, and Urinals A112.19.5-1999Hydraulic Performance Requirements for Water Closets and Urina
49、ls . A112.19.6-1995Whirlpool Bathtub Appliances .A112.19.7M-1995Suction Fittings for Use in Swimming Pools, Wading Pools,Spas, Hot Tubs, and Whirlpool Bathtub Appliances A112.19.8M-1987(R1996)Non-Vitreous Ceramic Plumbing Fixtures.A112.19.9M-1991(R1998)Dual Flush Devices for Water Closets A112.19.10-1994Wall Mounted and Pedestal Mounted, Adjustable and PivotingLavatory and Sink Carrier Systems. A112.19.12-2000Floor Drains .A112.21.1M-1991(R1998)Roof DrainsA112.21.2M-1983Hydrants for Utilit
