1、Designation: D 1007 05Standard Specification forsec-Butyl Alcohol1, 2This standard is issued under the fixed designation D 1007; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses ind
2、icates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers sec-butyl alcohol for use inpaint, varnish, lacquer, and related products.1.2 The values stated in SI units are to be regarded assta
3、ndard. No other units of measurement are included in thisstandard.1.3 The following applies to all specified limits in thisstandard; for purposes of determining conformance with thisstandard, an observed value or a calculated value shall berounded off “to the nearest unit” in the last right-hand dig
4、itused in expressing the specification limit, in accordance withthe rounding-off method of Practice E 29.1.4 For hazard information and guidance, see the suppliersMaterial Safety Data Sheet.2. Referenced Documents2.1 ASTM Standards:3D 268 Guide for Sampling and Testing Volatile Solventsand Chemical
5、Intermediates for Use in Paint and RelatedCoatings and MaterialD 1078 Test Method for Distillation Range of VolatileOrganic LiquidsD 1209 Test Method for Color of Clear Liquids (Platinum-Cobalt Scale)D 1353 Test Method for Nonvolatile Matter in VolatileSolvents for Use in Paint, Varnish, Lacquer, an
6、d RelatedProductsD 1364 Test Method for Water in Volatile Solvents (KarlFischer Reagent Titration Method)D 1613 Test Method for Acidity in Volatile Solvents andChemical Intermediates Used in Paint, Varnish, Lacquer,and Related ProductsD 4052 Test Method for Density and Relative Density ofLiquids by
7、Digital Density MeterD 5386 Test Method for Color of Liquids Using TristimulusColorimetryE1 Specification for ASTM Liquid-in-Glass ThermometersE29 Practice for Using Significant Digits in Test Data toDetermine Conformance with SpecificationsE 300 Practice for Sampling Industrial Chemicals2.2 U.S. Fe
8、deral Specification:PPP-C-2020 Chemicals, Liquid, Dry, and Paste: Packagingof43. Properties3.1 sec-Butyl alcohol shall conform to the following re-quirements:Apparent specific gravity:20/20C 0.807 to 0.809or25/25C 0.804 to 0.806Color, Pt-Co scale, maxA10Distillation range, 760 mmHg, C as:Initial boi
9、ling point, min 98.0Dry point, max 101.0Nonvolatile matter, max, mg/100 mL 5Water, max, weight % 0.5Acidity, as acetic acid, max, weight % 0.002B_AInstrumental Pt-Co color determined by Test Method D 5386 have been shownto have no statistically significant difference from Pt-Co color determined by T
10、estMethod D 1209. However, it is not known whether sec-butyl alcohol was part of thesample set included in the interlaboratory study.BEquivalent to 0.019 mg of KOH per gram of sample.4. Sampling4.1 The material shall be sampled in accordance withPractice E 300.5. Test Methods5.1 The properties enume
11、rated in this specification shall bedetermined in accordance with the following ASTM methods:5.1.1 Apparent Specific GravityDetermine the apparentspecific gravity at 20 or 25C by a convenient method that isaccurate to the third decimal place. See Guide D 268 or TestMethod D 4052.1This specification
12、is under the jurisdiction of ASTM CommitteeD01 on Paintand Related Coatings, Materials, and Applications and is the direct responsibilityD01.35 on Solvents, Plasticizers, and Chemical Intermediates.Current edition approved May 15, 2005. Published May 2005. Originallyapproved in 1949. Last previous e
13、dition approved in 2000 as D 1007 00.2This compound is also known under the names 2-butanol and secondarybutanol.3For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the
14、 standards Document Summary page onthe ASTM website.4Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, P
15、O Box C700, West Conshohocken, PA 19428-2959, United States.5.1.2 ColorTest Method D 1209 (see Note A in 3.1).5.1.3 Distillation RangeTest Method D 1078 using anASTM Solvents Distillation Thermometer 40C, having a rangefrom 72 to 126C and conforming to the requirements inSpecification E1.5.1.4 Nonvo
16、latile MatterTest Method D 1353.5.1.5 WaterTest Methods D 1364.5.1.6 AcidityTest Method D 1613.6. Packaging and Package Marking6.1 Package size shall be agreed upon between the pur-chaser and the supplier.6.2 Packaging shall conform to applicable carrier rules andregulations or when specified shall
17、conform to Fed. Spec.PPP-C-2020.7. Keywords7.1 methyl ethyl carbinol; sec-butylalcohol; 2hydroxybutaneSUMMARY OF CHANGESCommittee D01.35 has identified the location of selected changes to this standard since the last issue(D 1007 00) that may impact the use of this standard.(1) Added reference to Pr
18、actice E29in Scope section.(2) Added Practice E29and Test Method D 5386 to list ofReferenced documents.(3) Changed spec limits for apparent specific gravity in 3.1.(4) Added new Note A to 3.1.(5) Referenced new Note A in 5.1.2.ASTM International takes no position respecting the validity of any paten
19、t rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision a
20、t any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your commen
21、ts will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted
22、by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).D1007052
