1、Designation: D1044 081Standard Test Method forResistance of Transparent Plastics to Surface Abrasion1This standard is issued under the fixed designation D1044; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revisi
2、on. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1NOTEEditorially corrected Note 9 in February 2012.1. Scope*
3、1.1 This test method describes a procedure for estimatingthe resistance of transparent plastics to one kind of surfaceabrasion by measuring the change in optical properties.1.2 Abrasive damage is visually judged and numericallyquantified by the difference in haze percentage in accordancewith Test Me
4、thod D1003 between an abraded and unabradedspecimen.1.3 CS-10F wheels manufactured between October 2002and September 2004 have been found to give different resultsthan historical values. Comparisons of data using these wheelsshould be made with caution. Results using wheels made afterSeptember 2004
5、have agreed with those obtained beforeOctober 2002.1.4 The values stated in SI units are to be regarded asstandard. The values given in parentheses are for informationonly.NOTE 1This test method is equivalent to ISO 3537 in the measure-ment of resistance to abrasion in Section 7, but is not equivale
6、nt toISO 3537 in any other measurement or section. This test method is notequivalent to ISO 9352, and results cannot be directly compared betweenthe two methods.NOTE 2This test method is similar to ANSI/SAE Z26.1, Test 17.NOTE 3Prior attempts to employ the Taber Abraser for volume lossdeterminations
7、 of various plastics2have been unsuccessful because ofexcessively large coefficients of variation attributed to the data. Insuffi-cient agreement among the participating laboratories has rendered the useof volume loss procedure inadvisable as an ASTM test method.NOTE 4For determining the resistance
8、to abrasion of organic coatingsby weight loss, reference is made to Test Method D4060, which uses moreaggressive CS-10 or CS-17 abrasive wheels. It suffers from poor repro-ducibility between laboratories when numerical abrasion resistance valuesare used. Interlaboratory agreement improves significan
9、tly when rankinga series of coatings for their abrasion resistance.1.5 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the ap
10、plica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:3D618 Practice for Conditioning Plastics for TestingD1003 Test Method for Haze and Luminous Transmittanceof Transparent PlasticsD4000 Classification System for Specifying Plastic Materi-alsD4060 Test Method
11、 for Abrasion Resistance of OrganicCoatings by the Taber AbraserE691 Practice for Conducting an Interlaboratory Study toDetermine the Precision of a Test Method2.2 ISO Standards:4ISO 3537 Road VehiclesSafety Glazing MaterialsMechanical TestsISO 9352 PlasticsDetermination of Resistance to Wear byAbra
12、sive Wheels2.3 ANSI Standards:4ANSI/SAE Z26.1 Safety Glazing Materials for GlazingMotor Vehicle and Motor Vehicle Equipment Operatingon Land HighwaysAbrasion Resistance, Test 17 (Plas-tics)3. Terminology3.1 Definitions:3.1.1 abrasionabrasive wear caused by displacement orrearrangement of a softer ma
13、terial due to rubbing or scuffingagainst hard sharp particles.3.1.2 hazeIn accordance with Test Method D1003, thatpercentage of transmitted light which in passing through thespecimen deviates from the incident beam by forward scatter-ing. For the purpose of this test method, only light flux1This tes
14、t method is under the jurisdiction of ASTM Committee D20 on Plasticsand is the direct responsibility of Subcommittee D20.10 on Mechanical Properties.Current edition approved March 1, 2008. Published March 2008. Originallyapproved in 1949. Last previous edition approved in 2005 as D1044 - 05. DOI:10.
15、1520/D1044-08E01.2Supporting data are available from ASTM Headquarters. Request RR:D20-48and RR:D20-1090.3For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standar
16、ds Document Summary page onthe ASTM website.4Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C7
17、00, West Conshohocken, PA 19428-2959, United States.deviating more than 0.044 rad (2.5) on the average isconsidered to be haze.3.1.3 refacepreparation of an abrasive wheel on a condi-tioning stone prior to use in testing.3.1.4 wheelan abrasive wheel consisting of hard particles(aluminum oxide) embed
18、ded in resilient binder.4. Significance and Use4.1 Transparent plastic materials, when used as windows orenclosures, are subject to wiping and cleaning; hence themaintenance of optical quality of a material after abrasion isimportant. It is the purpose of this test method to provide ameans of estima
19、ting the resistance of such materials to this typeand degree of abrasion.4.2 Although this test method does not provide fundamentaldata, it is suitable for grading materials relative to this type ofabrasion in a manner which correlates with service.4.3 Comparison of interlaboratory data or the speci
20、ficationof a “haze” value has no significance if the hazemeterrequirements given in 5.4 are not used. This is because lightdiffused from the surface of a Taber track is scattered at anarrow angle (Fig. 1 and Fig. 2) while light diffused internallyby a specimen is scattered at a wide angle. In many h
21、azemeters,when a diaphragm is inserted to limit the light beam to thewidth of the abraded track, the specular beam at the exit portbecomes smaller. The dark annulus will then be greater than the0.023 6 0.002 rad (1.3 6 0.1) requirements of Test MethodD1003. Since a large percentage of the narrow-ang
22、le forward-scattered light will not impinge on the sphere wall, “haze”readings become smaller. For hazemeters that have not beenproperly adjusted, the magnitude of this reduction is dependentboth on the integrating sphere diameter and the reduction of theentrance beam.4.4 For many materials, there m
23、ay be a specification thatrequires the use of this test method, but with some proceduralmodifications that take precedence when adhering to thespecification. Therefore, it is advisable to refer to that materialspecification before using this test method. Table 1 of Classi-fication System D4000 lists
24、 the ASTM materials standards thatcurrently exist.4.5 For some materials, abrasion tests utilizing the Taberabraser may be subject to variation due to changes in theabrasive characteristics of the wheel during testing.4.5.1 Depending on abradant type and test specimen, thewheel surface may change (t
25、hat is, become clogged) due to thepick up of coating or other materials from test specimens andmust be cleaned at frequent intervals.4.5.2 The type of material being tested and the number oftest cycles being run is known to sometimes influence thetemperature of the running surface of the wheel with
26、an affecton the final haze measurement. To reduce any variability due tothis temperature effect, stabilize the wheels surface tempera-ture prior to performing actual measurements. This shall beaccomplished by conducting multiple refacings on an ST-11refacing stone, followed by a test on the sample m
27、aterial to betested (with results to be discarded).NOTE 1This photograph shows light pattern of the scattering from thesurface of a Taber abraded specimen. The circles show how increasing the1.3 dark annulus dramatically changes the amount of light impacting thesphere wall.FIG. 1 Light Scattering fr
28、om Surface of Abraded Tracks(Photograph)NOTE 1This graph shows goniophotometric curves for Taber abradedtracks. The specular angle of transmission is at 180.FIG. 2 Light Scattering from Surface of Abraded Tracks (Graph)D1044 08125. Apparatus5.1 AbraderThe Taber abraser or its equivalent, consist-ing
29、 of the following elements:5.1.1 Ahorizontal turntable platform; comprised of a rubberpad, clamp plate, and nut to secure the specimen to theturntable.5.1.2 A motor capable of rotating the turntable platform at aspeed of either 72 6 2 r/min for 110v/60Hz or 60 6 2 r/min for230v/50Hz.5.1.3 A pair of
30、pivoted arms, to which the abrasive wheelsand auxiliary masses (if used) would be attached; loads of 500or 1000 gf on the wheels are obtained by use of changeableweights.NOTE 5Without auxiliary masses or counterweights applied, eacharm will apply a load against the specimen of 250 gf per wheel (excl
31、usiveof the mass of the wheel itself).5.1.4 A vacuum suction system and vacuum pick-up nozzleto remove debris and abrasive particles from the specimensurface during testing. The height of the vacuum pick-upnozzle shall be adjustable, and the nozzle openings shall be 11mm716 in.) in diameter.NOTE 6Th
32、e nominal nozzle openings are 8 mm516 in.) and can beenlarged following the instructions shown in Appendix X2.5.1.5 A counter to record the number of cycles (revolutions)made by the turntable platform.5.2 Refacing StoneThe fine side of a ST-11 refacing stone(or equivalent) shall be used for refacing
33、 the abrasive wheels.It is important that the turntable platform runs true on theabraser and that the refacing stone lies flat on the turntableplatform.5.3 Abrasive WheelsThe grade of wheel designated CS-10F5shall be used, and shall meet the following requirementsat the time of the test:5.3.1 The wh
34、eel shall be 12.7 6 0.3 mm wide and have anexternal diameter of 51.9 6 0.5 mm when new, and in no caseless than 44.4 mm, and5.3.2 The wheel shall not be used after the date stamped onit.5.4 HazemeterAn integrating sphere photoelectric pho-tometer, as described in Test Method D1003, shall be used tom
35、easure the light scattered by the abraded track. If hazemeasurements are made with other devices or by other meth-ods, a correlation shall be established with the results obtainedwith the apparatus and method described in Test MethodD1003.5.4.1 An aperture or diaphragm shall be centrally inserted in
36、the haze measuring apparatus to center the light beam on theabraded track and limit it to a diameter of 7 6 1 mm 0.28 60.04 in.) at the specimen.5.4.2 When the reduced light beam is unobstructed by aspecimen, its cross section at the exit port shall be approxi-mately circular, sharply defined, unifo
37、rmly bright, and concen-tric within the exit port, leaving an annulus of 0.023 6 0.002rad (1.3 6 0.1) subtended at the entrance port.NOTE 7Uniformity of the light intensity is usually checked byobserving the beam through thin bond paper placed at the exit port.NOTE 8Forward-scattering glass standard
38、s6can be used to check thatthe optical system of the hazemeter is properly adjusted.5.5 Specimen HolderA suitable holder shall be used topermit positioning the abraded specimen on the hazemeter sothat the light beam is centered in the abraded track and thespecimen is flush at the measurement port.6.
39、 Test Specimens6.1 The test specimens shall be clean, transparent disksapproximately 100 mm in diameter or plates approximately100 mm square, having both surfaces substantially plane andparallel. They may be cut from sheets or molded in thicknessesup to 12.7 mm12 in.). A 6.3-mm14-in.) hole shall be
40、centrallydrilled in each specimen. Three such specimens shall be testedper sample, except for interlaboratory or specification testswhen ten specimens shall be tested.7. Calibration7.1 Verify calibration of the Taber abraser as directed by theequipment manufacturer (see Appendix X1).8. Conditioning8
41、.1 ConditioningUnless otherwise specified, conditionthe test specimens at 23 6 2C 73.4 6 3.6F) and 50 6 5%relative humidity for not less than 40 h prior to test inaccordance with Procedure A of Practice D618. In cases ofdisagreement, the tolerances shall be 61C 61.8F) and 62%relative humidity.8.2 Te
42、st ConditionsConduct tests in the standard labora-tory atmosphere of 23 6 2C 73.4 6 3.6F) and 50 6 5%relative humidity, unless otherwise specified. In cases ofdisagreements, the tolerances shall be 61C 61.8F) and62 % relative humidity.9. Standardization of Abrading Wheels9.1 To ensure that the abrad
43、ing function of the wheels ismaintained at a constant level, prepare the abrading wheelsprior to each test.9.1.1 Mount the wheels on their respective flange holders,taking care not to handle them by their abrasive surfaces.9.1.2 Select the load to be used and affix it to the abraser. Ifno load is sp
44、ecified, use a load of 500 gf (per wheel).9.1.3 Mount an ST-11 refacing stone (or equivalent) on theturntable, fine side up, and secure using the nut.9.1.4 Lower the vacuum nozzle and adjust its height towithin 0.8 to 1.6 mm132 to116 in.) of the refacing stone. Setthe vacuum suction force to 100.9.1
45、.5 Lower the arms so the wheels contact the surface ofthe ST-11 refacing stone.5The sole source of supply of the apparatus known to the committee at this timeis Taber Industries, 455 Bryant Street, North Tonawanda, NY 14120. If you areaware of alternative suppliers, please provide this information t
46、o ASTM Interna-tional Headquarters. Your comments will receive careful consideration at a meetingof the responsible technical committee,1which you may attend.6Calibrated plastic haze standards are available from BYK-Gardner, Inc., 9104Guilford Road, Columbia, MD 21046.D1044 08139.2 Before abrading e
47、ach specimen, reface the wheels for 25cycles on the fine side of the ST-11 refacing stone. Afterrefacing, use a soft bristle, anti-static brush to lightly brush thewheel surfaces to remove any loose particulate matter beforeabrading a specimen. (WarningDo not touch the runningsurface of the wheels a
48、fter they are refaced. New wheels orwheels trued using a diamond tool refacer, must first be brokenin with 100 cycles on the fine side of the ST-11 refacing stonefollowed by a test on the material to be evaluated (results to bediscarded).)NOTE 9A brush found suitable for this purpose has been descri
49、bed asfollows: Having a width of two inches with tuft spacing of 0.25 inches. Itis a soft-fiber, static-dissipative brush manufactured from an acrylic fiber(0.0015 inch filament diameter) that has been chemically bonded with alayer of copper sulfide to produce a resistance of 35 times 10-4ohms percentimetre.NOTE 10The fine side of the ST-11 refacing stone has a limited lifeand must be replaced after 10,000 cycles (approximately 400 refacings).9.2.1 A thin fin of wheel material will sometimes form onthe left hand edge of the wheel
