1、Designation: D 1646 07Standard Test Methods forRubberViscosity, Stress Relaxation, and Pre-VulcanizationCharacteristics (Mooney Viscometer)1This standard is issued under the fixed designation D 1646; the number immediately following the designation indicates the year oforiginal adoption or, in the c
2、ase of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 These t
3、est methods cover procedures for measuring aproperty called Mooney viscosity. Mooney viscosity is definedas the shearing torque resisting rotation of a cylindrical metaldisk (or rotor) embedded in rubber within a cylindrical cavity.The dimensions of the shearing disk viscometer, test tempera-tures,
4、and procedures for determining Mooney viscosity aredefined in these test methods.1.2 When disk rotation is abruptly stopped, the torque orstress on the rotor decreases at some rate depending on therubber being tested and the temperature of the test. This iscalled “stress relaxation” and these test m
5、ethods describe a testmethod for measuring this relaxation.NOTE 1Viscosity as used in these test methods is not a true viscosityand should be interpreted to mean Mooney viscosity, a measure ofshearing torque averaged over a range of shearing rates. Stress relaxationis also a function of the test con
6、figuration and for these test methods theresults are unique to the Mooney viscometer.1.3 When compounded rubber is placed in the Mooneyviscometer at a temperature at which vulcanization may occur,the vulcanization reaction produces an increase in torque.These test methods include procedures for meas
7、uring the initialrate of rubber vulcanization.1.4 ISO 289 Parts 1 and 2 also describes the determinationof Mooney viscosity and pre-vulcanization characteristics. Inaddition to a few insignificant differences there are majortechnical differences between ISO 289 and this test method inthat ISO 289 do
8、es not provide for sample preparation on a mill,while this test method allows milling sample preparation insome cases prior to running a Mooney viscosity test. This canresult in different viscosity values for some rubbers.1.5 The values stated in SI units are to be regarded as thestandard. The value
9、s given in parentheses are for informationonly.1.6 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regu
10、latory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D 1349 Practice for RubberStandard Temperatures forTestingD 1418 Practice for Rubber and Rubber LaticesNomenclatureD 1485 Practice for Rubber from Natural SourcesSampling and Sample PreparationD 3182 Practice for RubberMateri
11、als, Equipment, andProcedures for Mixing Standard Compounds and Prepar-ing Standard Vulcanized SheetsD 3185 Test Methods for RubberEvaluation of SBR(Styrene-Butadiene Rubber) Including Mixtures With OilD 3186 Test Methods for RubberEvaluation of SBR(Styrene-Butadiene Rubber) Mixed With Carbon Black
12、orCarbon Black and OilD 3896 Practice for Rubber From Synthetic SourcesSamplingD 4483 Practice for Evaluating Precision for Test MethodStandards in the Rubber and Carbon Black ManufacturingIndustries2.2 ISO Standard:3ISO 289 Rubber, UnvulcanizedDeterminations Using theShearing Disk Viscometer,Part 1
13、 Determination of Mooney Viscosity, andPart 2 Determination of Prevulcanization Characteristics.3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 Mooney viscosity, nmeasure of the viscosity of arubber or rubber compound determined in a Mooney shearing1These test methods are unde
14、r the jurisdiction of ASTM Committee D11 onRubber and are the direct responsibility of Subcommittee D11.12 on ProcessabilityTests.Current edition approved Nov. 1, 2007. Published November 2007. Originallyapproved in 1959. Last previous edition approved in 2006 as D 1646 06.2For referenced ASTM stand
15、ards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor,
16、 New York, NY 10036.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.Copyright by ASTM Intl (all rights reserved); Tue Apr 1 21:46:07 EST 2008Downloaded/printed byGuo Dehua (CNIS) pursuant to License Agreement. No further reproduction
17、s authorized.disk viscometer; viscosity is indicated by the torque required torotate a disk embedded in a rubber specimen and enclosed inthe die cavity under specified conditions.3.1.2 pre-vulcanization characteristics, nfor a vulcaniz-able compound, a measure of the time to the incipientvulcanizati
18、on and the rate of cure during the early stages ofvulcanization.3.1.3 stress relaxation, nresponse of a raw or com-pounded rubber to a rapid cessation of flow or a suddendeformation; specific to the use of the shearing disk viscom-eter, it takes the form of a decaying level of stress initiated bysud
19、denly stopping the rotation of the disk.3.1.4 test temperature, nsteady-state temperature of theclosed dies with rotor in place and the cavity empty; thissteady-state temperature shall be measured within the dies asdescribed in 6.1.3.4. Summary of Test Methods4.1 These test methods are divided into
20、three parts:4.1.1 Part AViscosity: This test method describes themeasurement of the Mooney viscosity. The Mooney viscosityis measured by a metal disk embedded in a rubber specimencontained in a rigid cylindrical cavity maintained at a specifiedpressure and temperature. The disk is slowly and continu
21、ouslyrotated in one direction for a specified time. The resistance tothis rotation offered by the rubber is measured in arbitrarytorque units as the Mooney viscosity of the specimen.4.1.2 Part BStress Relaxation: This test method de-scribes the procedure to measure stress relaxation. At the endof a
22、Mooney viscosity test, the rotation of the metal disk issuddenly stopped and the rate of decrease of torque ismonitored as a function of time.4.1.3 Part CPre-Vulcanization Characteristics: This testmethod describes how pre-vulcanization properties may bemeasured. The viscosity of vulcanizable rubber
23、 compounds isrecorded during heating at a specified temperature. The mini-mum viscosity and the times for the viscosity to increase byspecified amounts are used as arbitrary measures of the startand rate of vulcanization.5. Significance and Use5.1 ViscosityViscosity values determined by this testmet
24、hod depend on molecular structure, molecular weight, andnon-rubber constituents that may be present. Since rubberbehaves as a non-Newtonian fluid, no simple relationshipexists between the molecular weight and the viscosity. There-fore, caution must be exercised in interpreting viscosity valuesof rub
25、ber, particularly in cases where molecular weight is veryhigh. For example, as the molecular weight increases, theviscosity values for IIR polymers (butyl rubbers) reach anupper limit of about 80, at 100C (212F) using a large rotor ata rotation speed of 2 r/min, and may then decrease toconsiderably
26、lower values. For these higher molecular weightrubbers, better correlation between viscosity values and mo-lecular weight is obtained if the test temperature is increased.5.2 Stress RelaxationThe stress relaxation behavior ofrubber is a combination of both an elastic and a viscousresponse. Viscosity
27、 and stress relaxation behavior do notdepend on such factors as molecular weight and non-rubberconstituents in the same way. Thus both of these tests areimportant and complement each other.Aslow rate of relaxationindicates a higher elastic component in the overall response,while a rapid rate of rela
28、xation indicates a higher viscouscomponent. The rate of stress relaxation has been found tocorrelate with rubber structure characteristics such as molecu-lar weight distribution, chain branching, and gel content.5.3 Pre-Vulcanization CharacteristicsThe onset of vulca-nization can be detected with th
29、e Mooney viscometer asevidenced by an increase in viscosity. Therefore, this testmethod can be used to measure incipient cure (scorch) time andthe rate of cure during very early stages of vulcanization. Thistest method cannot be used to study complete vulcanizationbecause the continuous rotation of
30、the disk will result inslippage when the specimen reaches a stiff consistency.6. Apparatus6.1 Mooney ViscometerAn instrument consisting of amotor-driven rotating disk within a cylindrical die cavityformed by two dies maintained at specified conditions oftemperature and die closure force. The Mooney
31、viscometermeasures the effect of temperature and time on the viscosity ofrubbers. If the stress relaxation test is to be performed, theinstrument must be capable of quickly stopping the rotation ofthe disk and monitoring the relaxation of stress versus time.The die-rotor relationship of an example d
32、esign is shown inFig. 1. The Mooney viscometer shall incorporate the followingcomponents:6.1.1 DiesThe dies and die holders forming the die cavityshall be fabricated from a nondeforming tool steel, shall havean unplated finish, and shall be hardened to a Rockwellhardness of 60 HRC minimum. The dimen
33、sions of the diecavity, measured from the highest surfaces, shall be 50.93 60.13 mm (2.005 6 0.005 in.) in diameter and 10.59 6 0.03 mm(0.417 6 0.001 in.) in depth. The surfaces of the die cavityshall either be serrated or contain V-grooves to minimizeslippage of the specimen.NOTE 2The two types of
34、dies may not give the same results.6.1.1.1 Serrated DiesWhen the cavity is formed fromfour pieces of steel, serrations on the surfaces of the dies anddie holders are used. These serrations consist of rectangulargrooves 0.8 6 0.02 mm (0.031 6 0.0008 in.) wide with auniform depth of not less than 0.25
35、 mm (0.010 in.) nor morethan 0.38 mm (0.015 in.). The grooves shall be vertical andshall be cut on 1.6 6 0.04 mm (0.063 6 0.002 in.) centers. Theserrations of the dies shall consist of two sets of such groovesat right angles to each other.6.1.1.2 Radial Grooved DiesWhen the die cavity isformed from
36、two pieces of steel, radialV-grooves are used onlyon the flat surfaces of the die cavity. The grooves shall bespaced at 20 intervals and shall form a 90 angle in the diesurfaces with the bisector of the angle perpendicular to thesurface. They shall extend from the 7-mm (0.281-in.) circle tothe 47-mm
37、 (1.875-in.) circle in the upper die and from the12-mm (0.472-in.) circle to the 47-mm circle in the lower die.The grooves shall be 1 6 0.1 mm (0.04 6 0.004 in.) wide atthe surface.D1646072Copyright by ASTM Intl (all rights reserved); Tue Apr 1 21:46:07 EST 2008Downloaded/printed byGuo Dehua (CNIS)
38、pursuant to License Agreement. No further reproductions authorized.NOTE 3Die wear can affect test results, usually to a lesser extent thanrotor wear. As a general practice, many users replace dies every secondtime they replace worn rotors (see 6.1.2.1). This practice may not apply toall materials te
39、sted, as wear is material dependent. The ultimate way todetermine if die wear has affected test results is to replace the dies with anew set and determine if the test results are changed.6.1.1.3 Mounting of DiesThe dies shall be an integral partof or mounted on platens equipped with a heating device
40、 andcontrols capable of maintaining the die cavity at the specifiedtest temperature with a tolerance of 60.5C (61F) at equi-librium conditions.6.1.1.4 Die ClosureThe viscometer shall have a suitabledevice for opening and closing the platens and dies and forholding them closed during a test. During a
41、 test it is extremelyimportant that the die cavity be held closed with the correctforce. To obtain the correct closing force for the mechanical-type closures, follow explicitly either the manufacturers rec-ommendation or other procedure of equal reliability.4Pneu-matically closed dies shall be held
42、closed during the test witha force of 11.5 6 0.5 kN (2585 6 115 lbf).Agreater force maybe required to close the dies when testing extremely toughstocks. At least 10 s before the motor is started, the forceshould be set to 11.5 6 0.5 kN. The die closure shall be suchthat a piece of thin soft tissue (
43、with a thickness not greater than0.04 mm (0.0015 in.) placed between the meeting surfaceswill retain a continuous pattern of uniform intensity when thedies are closed upon it.Anonuniform pattern indicates wear ofthe die holder surface, misalignment, or distortion of dies anddie holders.Any of these
44、situations will result in undue leakageand erroneous results.NOTE 4For mechanical-type closure viscometers, the pressure on thedie cavities may change if the viscometer is used at a different temperaturethan that at which it is adjusted.6.1.2 RotorsTwo rotors are specified, differing only intheir di
45、ameter. They shall be fabricated from a nondeformingtool steel, shall have an unplated finish and shall be hardenedto a Rockwell hardness of 60 HRC minimum. The large rotorshall be 38.10 6 0.03 mm (1.500 6 0.001 in.) in diameter and5.54 6 0.03 mm (0.218 6 0.001 in.) in thickness as measuredfrom the
46、highest points. The small rotor shall conform to thelarge rotor except the diameter shall be 30.48 6 0.03 mm(1.200 6 0.001 in.). The serrations on the face of the rotor shallconform to the requirements for the serrated dies given in6.1.1.1 and the serrations on the edge of the rotor shall conformto
47、the requirements specified for the serrated die holders. Therotor head shall be securely mounted perpendicularly to asuitable straight cylindrical stem not exceeding 11 mm(0.433 in.) in diameter. The rotor head shall be positioned sothat the top and bottom surfaces are 2.54 6 0.10 mm (0.100 60.005 i
48、n.) from the surfaces of the top and bottom dies,respectively, when the dies are closed. The wear tolerance fromthe center position should not exceed 60.25 mm (60.010 in.).A suitable seal shall be provided in the lower die having aminimum clearance and constant torque when the machine isrun empty. T
49、he eccentricity, or runout, shall not exceed 0.1mm.6.1.2.1 Rotor wear will affect test results.Any rotor worn tosuch an extent that the rotor diameter is less than the minimumdiameter shown in this procedure shall not be used.4Decker, G. E., “Note on the Adjustment of the Mooney Viscometer DieClosure,” ASTM Bulletin, No. 195, January 1954, p. 51.FIG. 1 Relationship of Platens, Dies, and Rotor in a Typical Shearing Disk ViscometerD1646073Copyright by ASTM Intl (all rights reserved); Tue Apr 1 21:46:07 EST 2008Downloaded/printed byGuo Dehua (CNI
