1、Designation: D2053 99 (Reapproved 2010)Standard Test Method forColorfastness of Zippers to Light1This standard is issued under the fixed designation D2053; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision.
2、A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the determination of the alter-ation in shade of the textile portion of zippers when exposed tolight, regardl
3、ess of the materials of manufacture.1.2 The values stated in either SI units or inch-pound unitsare to be regarded separately as the standard. Within the text,the inch-pound units are shown in parentheses. The valuesstated in each system are not exact equivalents; therefore, eachsystem shall be used
4、 independently of the other. Combiningvalues from the two systems may result in nonconformancewith this test method.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate
5、 safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D123 Terminology Relating to TextilesD2050 Terminology Relating to SubassembliesD2051 Test Method for Durability of Finish of Zippers toLaunderingD2052 Test
6、 Method for Colorfastness of Zippers to Dry-cleaningD2054 Test Method for Colorfastness of Zipper Tapes toCrockingD2057 Test Method for Colorfastness of Zippers to Laun-deringD2058 Test Method for Durability of Finish of Zippers toDrycleaningD2059 Test Method for Resistance of Zippers to Salt Spray(
7、Fog)D2060 Test Methods for Measuring Zipper DimensionsD2061 Test Methods for Strength Tests for ZippersD2062 Test Methods for Operability of Zippers2.2 AATCC Methods:Test Method 16 Colorfastness to Light3AATCC Gray Scale for Color Change3Evaluation Procedure 1 Gray Scale for Color Change33. Terminol
8、ogy3.1 DefinitionsFor definitions of zipper terms used in thisstandard, refer to Terminology D2050. For definitions of othertextile terminology used in this standard, refer to TerminologyD123.4. Summary of Test Method4.1 A specimen of zipper tape and chain is exposed tocontinuous artificial light fo
9、r a predetermined period of expo-sure. Fading of the specimen is evaluated and rated by meansof the AATCC Gray Scale for Color Change.5. Significance and Use5.1 This test method is useful in determining if the loss ofcolor due to light exposure is satisfactory for the intendedend-use.5.2 This test m
10、ethod is considered satisfactory for accep-tance testing of commercial shipments because the method hasbeen used extensively in the trade for acceptance testing.5.2.1 If there are differences of practical significance be-tween reported test results for two laboratories (or more),comparative tests sh
11、ould be performed to determine if their isa statistical bias between them, using competent statisticalassistance. As a minimum, the test samples should be used thatare as homogeneous as possible, that are drawn from thematerial from which the disparate test results were obtained,and that are randoml
12、y assigned in equal numbers to eachlaboratory for testing. Other materials with established testvalues may be used for this purpose. The test results from thetwo laboratories should be compared using a statistical test forunpaired data, at a probability level chosen prior to the testingseries. If a
13、bias is found, either its cause must be found andcorrected, or future test results must be adjusted in consider-ation of the known bias.5.3 The test method(s) in this standard along with those inTest Methods D2051, D2052, D2054, D2057, D2058, D2059,1This test method is under the jurisdiction of ASTM
14、 Committee D13 on Textilesand is the direct responsibility of Subcommittee D13.54 on Subassemblies. This testmethod was developed in cooperation with the Slide Fastener Association, Inc.Current edition approved June 1, 2010. Published August 2010. Originallyapproved in 1961. Last previous edition ap
15、proved in 2004 as D2053 99(2004).DOI: 10.1520/D2053-99R10.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Te
16、chnical Manual of the American Association of Textile Chemists andColorists, P. O. Box 12215, Research Triangle Park, NC 27709.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.D2060, D2061, and D2062 are a collection of proven zippert
17、est methods. They can be used as aids in the evaluation ofzippers without the need for a thorough knowledge of zippers.The enumerated test methods do not provide for the evaluationof all zipper properties. Besides those properties measured bymeans of the enumerated test methods there are other prope
18、r-ties that may be important for the satisfactory performance ofa zipper. Test methods for measuring those properties have notbeen published either because no practical methods have yetbeen developed or because a valid evaluation of the informa-tion resulting from existing unpublished methods requir
19、es anintimate and thorough knowledge of zippers.6. Sampling and Test Specimens6.1 Primary Sampling UnitConsider individual contain-ers from each shipping carton to be the primary sampling units.6.2 Laboratory Sampling UnitAs a laboratory samplingunit, take at random one zipper from each primary samp
20、lingunit.6.3 Test SpecimensAs a test specimen, take approxi-mately a 120-mm (4.75-in.) length of the laboratory samplethat consists of the tape and chain.7. Mounting the Test Specimen7.1 Mount the specimen front face up, as prescribed inAATCC Test Method 16, with approximately half the specimencover
21、ed and the remainder exposed.8. Procedure8.1 Test the specimen for colorfastness as directed inAATCC Test Method 16.NOTE 1There are distinct differences in spectral distribution betweenthe various types of machines listed in AATCC Test Method 16, with nooverall correlations between them. Consequentl
22、y, these machines cannotbe used interchangeably. In case of controversy, results obtained with thewater-cooled Xenon-arc machine listed in Option E shall prevail.9. Interpretation of Results9.1 Interpret the results of the test on the specimens asdirected in AATCC Test Method 16 for the selected opt
23、ion, asappropriate, using the Classification Based on a SpecifiedNumber of Standard Fading Hours or AATCC Fading Units.10. Report10.1 State that the specimens were tested as directed in theTest Method D2053. Describe the material or product sampled,and the method of sampling used.10.2 Report the fol
24、lowing information for the laboratorysampling unit and for the lot as applicable to a materialspecification or contract order.10.2.1 Specify the AATCC Test Method 16 option used,10.2.2 Number of specimens tested,10.2.3 Degree of fading as standard fading hours orAATCCFading Units, as appropriate, an
25、d10.2.4 Degree of fading for each specimen as the appropri-ate grade on the AATCC Gray Scale for Color Change.11. Precision and Bias11.1 PrecisionIt is not possible to specify the precision ofthis test method because of the restricted and nonlinearrelationships between the rating scales of color dif
26、ferenceunits, and the increased variability in color difference units asthe true value of ratings decrease.11.2 BiasThe procedure of this test method produces atest value that can be defined only in terms of a test method.There is no independent, referee method by which bias may bedetermined. This t
27、est method has no known bias.12. Keywords12.1 colorfastness; zipperASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any
28、such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are inv
29、ited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received
30、 a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of th
31、is standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).D2053 99 (2010)2
