1、Designation: D580/D580M 10Standard Specification forGreige Woven Glass Tapes and Webbings1This standard is issued under the fixed designation D580/D580M; the number immediately following the designation indicates the yearof original adoption or, in the case of revision, the year of last revision. A
2、number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification primarily covers greige tapes andwebbings woven from “E” electrical classification glass fiberyarns. This specificat
3、ion can also be applied to tapes andwebbings made of other glass fiber grades upon agreementbetween the purchaser and the supplier.1.2 This specification is intended to assist ultimate users bydesignating the types of these products that are typical in theindustry. This specification permits the app
4、lication of organicmaterials to the glass fiber yarn during manufacture that helpsfacilitate weaving. When used as permitted in this specifica-tion, such materials will not interfere with the intended end userequirements.1.3 The values stated in either SI units or inch-pound unitsare to be regarded
5、separately as standard. The values stated ineach system may not be exact equivalents; therefore, eachsystem shall be used independently of the other. Combiningvalues from the two systems may result in nonconformancewith the standard.1.4 This standard does not purport to address all of thesafety conc
6、erns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D123 Terminology Relating to TextilesD5
7、78 Specification for Glass Fiber StrandsD579 Specification for Greige Woven Glass FabricsD1059 Test Method for Yarn Number Based on Short-Length SpecimensD1423 Test Method for Twist in Yarns by Direct-CountingD1776 Practice for Conditioning and Testing TextilesD1777 Test Method for Thickness of Text
8、ile MaterialsD3773 Test Methods for Length of Woven FabricD3774 Test Method for Width of Textile FabricD3775 Test Method for Warp (End) and Filling (Pick)Count of Woven FabricsD4963 Test Method for Ignition Loss of Glass Strands andFabricsD5035 Test Method for Breaking Force and Elongation ofTextile
9、 Fabrics (Strip Method)D7018 Terminology Relating to Glass Fiber and Its Prod-ucts2.2 ANSI Standard:3ANSI/ASQC Z1.4 Sampling Procedures for Inspection byAttributes3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 For definitions of glass fiber and product terms used inthis speci
10、fication refer to Terminology D7018.3.1.2 The following terms are relevant to this standard:continuous filament yarn, greige goods, tape, webbing.3.1.3 For definitions of other textile terminology used in thisspecification, refer to Terminology D123.4. Classification4.1 Greige glass fiber tapes and
11、webbings are produced intwo types and are constructed with yarns designated as directedin Specification D578. The standard types are:4.1.1 Type AMedium texture.4.1.2 Type BOpen texture.4.2 The designation of a tape or webbing shall be by stylenumbers that are standard throughout the industry.4.3 Two
12、 segments of characters are used to describe tapesand webbings.4.3.1 The first segment of the description of tape or webbingdescribes the glass classification, the type fiber in the warp, andthe type fiber in the filling.4.3.1.1 The first letter in the first segment is one of thefollowing glass clas
13、sification codes: “E” for electrical,“ C” forchemical, “S” for high strength.4.3.1.2 The second letter in the first segment specifies thefiber type in the warp direction: “C” describes continuous1This specification is under the jurisdiction of ASTM Committee D13 onTextiles and is the direct responsi
14、bility of Subcommittee D13.18 on Glass Fiber andits Products.Current edition approved June 1, 2010. Published July 2010. Originally approvedin 1940. Last previous edition approved in 2004 as D580 04. DOI: 10.1520/D0580_D0580M-10.2For referenced ASTM standards, visit the ASTM website, www.astm.org, o
15、rcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute, 11 W. 42nd St., 13thFloor, New York, NY 10036.1Copyright ASTM International,
16、100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.filament fiber using either SI units or inch-pound units, staple(discontinuous) fiber is described by “D” in SI units or “S” ininch-pound units.4.3.1.3 The third letter in the first segment specifies the fibertype in
17、 the filling direction: “C” describes continuous filamentfiber using either SI units or inch-pound units, staple (discon-tinuous) fiber is described by “D” in SI units or “S” ininch-pound units.4.3.2 The second segment of the description of tape orwebbing describes the texture: “A” describes medium
18、textureand“ B” describes close texture.4.4 Examples of glass fiber tapes or webbings.4.4.1 Example 1a (SI units):ECD 2 B (1)where:E = electrical glass,C = continuous filament yarn warp direction,D = discontinuous (staple) yarn filling direction, andB = close textured.4.4.2 Example 1b inch-pound unit
19、s:ECS 2 B (2)where:E = electrical glass,C = continuous filament yarn warp direction,S = staple (discontinuous) filament yarn filling direction,andB = close textured.REQUIREMENTS5. Material5.1 The fiber shall be continuous filament or staple (discon-tinuous) fiber, as agreed upon between the purchase
20、r andsupplier, free of any free alkali metal salts, such as soda orpotash, and foreign particles, dirt, and other impurities.6. Fabric Count6.1 For tapes listed in Tables 1 and 2, and webbings listed inTable 3, the nominal fabric count shall conform to therequirements of Table 1, Table 2, and Table
21、3, respectively. Fortapes or webbings not listed in Table 1, Table 2, and Table 3,the nominal fabric count shall be agreed upon between thepurchaser and the supplier. The average count of warp endsshall be within one end of the nominal count and the averagecount of the filling picks shall be within
22、two picks of thenominal count.7. Yarn Designations7.1 For tapes and webbings, the yarn designations shall beas agreed upon between the purchaser and supplier. Therequirements of the individual elements of the designation arespecified in Sections 8-12.8. Yarn Number8.1 For tapes and webbings, the nom
23、inal size-free yarnnumbers of the yarns designated shall conform to SpecificationD578.9. Filament Diameter9.1 The nominal values for the filament diameters whenagreed upon between purchaser and supplier are listed in Table1 of Specification D578. The average filament diameter for theyarns in the tap
24、e or webbing shall conform to SpecificationD578 for the specified filament diameter.10. Strand Construction10.1 The basis for specifying strand construction is given inSpecification D578. The construction of the component strandsshall be agreed upon between the purchaser and the supplier.11. Directi
25、on of Twist11.1 Unless otherwise agreed upon between the purchaserand the supplier, the primary twist in the singles strands shallbe “Z” twist and the final twist in the plied yarns shall be “S”twist.12. Twist Level12.1 The nominal twist in the component strands and thefinished yarns shall be agreed
26、 upon between the purchaser andsupplier. The tolerances for the primary twist and the final twistshall conform to Table 4.13. Tape Weave Type13.1 For tapes listed in Tables 1 and 2 and webbings listedin Table 3, the weave type shall be plain weave. For tapes andwebbings not listed in Table 1, Table
27、2, and Table 3, the weavetype shall be agreed upon between the purchaser and thesupplier.14. Length per Unit Mass14.1 For tapes listed in Tables 1 and 2, and webbings listedin Table 3, the nominal length per unit mass shall conform tothe requirements of Table 1, Table 2, and Table 3, respectively.Fo
28、r tapes and webbings not listed in Table 1, Table 2, and Table3, the nominal length per unit mass shall be agreed uponbetween the purchaser and the supplier. The average length perunit mass for the lot shall be within the interval: specifiedlength per unit mass 610 %.15. Thickness15.1 For tapes list
29、ed in Tables 1 and 2, and webbings listedin Table 3, the nominal thickness shall conform to therequirements of Table 1, Table 2, and Table 3, respectively. ForD580/D580M 102tapes and webbings not listed in Table 1, Table 2, and Table 3,the nominal thickness shall be agreed upon between thepurchaser
30、and the supplier. The average thickness of the tape orwebbing in the lot shall conform to the requirements of Table5, unless specified otherwise.16. Breaking Strength16.1 For tapes listed in Tables 1 and 2, and webbings listedin Table 3, the average breaking strength shall conform to therequirements
31、 of Table 1, Table 2, and Table 3, respectively. ForTABLE 1 Physical Properties of Generally Available “E” Glass Greige Woven Glass Continuous Filament Tape, Plain WeaveTape No.Thickness WidthTotal EndsPick CountLength perUnit MassMinimumBreaking Strengthmm in. mm in. 25 mm in. tex yd/lb N lbfECC-A
32、0.130 0.005 12.712 24 34 35 1923 258 445 10019.034 32 34 35 2681 185 600 13525.4 1 42 34 35 3543 140 712 16025.4 1 36 33 34 3398 146 712 16038.1 112 62 34 35 5222 95 1112 25050.8 2 72 33 34 6795 73 1334 30063.5 212 104 34 35 9186 54 1557 35076.2 3 108 33 34 10124 49 2224 500102.0 4 144 33 34 13407 3
33、7 2513 565ECC-A 0.180 0.007 12.712 24 31 32 2771 179 578 13019.034 32 31 32 3875 128 778 17525.4 1 42 31 32 5114 97 1068 24038.1 112 62 31 32 7404 67 1646 37050.8 2 88 31 32 10334 48 2313 5200.255 0.010 12.712 16 21 21 3730 133 712 16019.034 24 21 21 5574 89 1112 25025.4 1 32 21 21 7295 68 1557 3503
34、8.1 112 48 21 21 11023 45 2446 550ECC-A 0.380 0.015 12.712 14 16 16 5222 95 934 21019.034 20 16 16 7516 66 1423 32025.4 1 26 16 16 9921 50 1957 44038.1 112 40 16 16 15032 33 2936 660ECC-B 0.075 0.003 9.538 21 41 42 800 620 200 4512.712 30 41 42 1184 419 267 6019.034 45 41 42 1759 282 423 9525.4 1 63
35、 41 42 2408 206 600 13538.1 112 108 41 42 4066 122 845 1900.130 0.005 9.538 21 38 39 1778 279 512 11512.712 27 38 39 2297 216 600 13519.034 39 38 39 3329 149 1001 22525.4 1 51 38 39 4390 113 1379 31038.1 112 75 38 39 6442 77 1957 440ECC-B 0.178 0.007 9.538 21 38 39 2147 231 512 11512.712 27 38 39 27
36、71 179 600 13538.134 39 38 39 4033 123 1001 22525.4 1 51 38 39 5277 94 1379 31038.1 112 75 38 39 7874 63 1957 440TABLE 2 Physical Properties of Generally Available “E” Glass Greige Woven Glass Staple (Discontinuous) Filament Tape, Plain WeaveTape No.Thickness WidthTotal EndsPick CountLength perUnit
37、MassMinimumBreakingStrengthmm in. mm in. 25 mm in. tex yd/lb N lbfESS-A 0.255 0.010 12.712 18 21 21 3906 127 445 10019.034 26 21 21 5977 83 667 15025.4 1 34 21 21 7632 65 890 20038.1 112 52 21 21 11811 42 1334 3000.038 0.015 19.034 20 16.5 16.5 8268 60 890 20025.4 1 28 16.5 16.5 11023 45 1112 25038.
38、1 112 52 16.5 16.5 17105 29 1557 350D580/D580M 103tapes and webbings not listed in Table 1, Table 2, and Table 3,the average breaking strength shall be agreed upon between thepurchaser and the supplier. The average breaking strength forthe lot shall exceed the specified breaking strength and noindiv
39、idual break shall be less than 80 % of the specifiedaverage breaking strength.17. Width17.1 For tapes listed in Tables 1 and 2, and webbings listedinTable 3, the nominal width shall conform to the requirementsof Table 1, Table 2, and Table 3, respectively. For tapes andwebbings not listed in Table 1
40、, Table 2, and Table 3, thenominal width shall be agreed upon between the purchaser andthe supplier. The tolerances for width shall conform to Table 6unless otherwise agreed upon between the purchaser and thesupplier.18. Length Per Package18.1 The nominal length of tape or webbing on eachpackage, su
41、ch as a spool or serving tube, shall be no more than36 m 40 yd nor no less than 32 m 36 yd except for 0.075mm 0.003 in. thick tape or webbing which shall be no morethan 68 m 76 yd nor no less than 65 m 72 yd, unlessotherwise agreed upon between the purchaser and the supplier.18.2 Unless otherwise ag
42、reed upon between the purchaserand the supplier, no piece of tape or webbing shall be less than14 m 15 yd long and there shall be no more than two piecesin a package.18.3 None of the sample tubes or serving spools shallcontain more than the allowable pieces, and the combinedlength of all of the samp
43、le tubes or serving spools shall not beless than the combined length of those tubes or serving spoolson the identification labels.TABLE 3 Physical Properties of Generally Available “E” Glass Greige Woven Glass Staple (Discontinuous) Filament Webbing, PlainWeaveTape No.Thickness WidthTotal EndsPick C
44、ountLength perUnit MassMinimumBreakingStrengthmm in. mm in. 25 mm in. tex yd/lb N lbfESS-A 0.510 0.020 19.034 20 14 14 10124 49 1112 25025.4 1 28 14 14 13779 36 1334 30038.1 112 44 14 14 19842 25 2002 4500.635 0.025 19.034 20 10 10 11274 44 934 21025.4 1 28 10 10 15502 32 1334 30038.1 112 44 10 10 2
45、7559 18 2446 550TABLE 4 Twist TolerancesTolerancesTurns per Centimeter:From zero to 0.4 60.1 turn per centimeterOver 0.4 and up to and 60.2 turn per centimeterincluding 4.0Over 4 65.0 % of the specifiedaverage twistTurns per Meter:From zero to 40, incl 610 turns per meterOver 40 and up to and 620 tu
46、rns per meterincluding 400Over 400 65.0 % of the specifiedav erage twistTurns per Inch:From zero to 1 60.25 turn per inchOver 1 and up to and 60.5 turn per inchincluding 10Over 10 65.0 % of the specifiedaverage twistTABLE 5 TolerancesThicknessNominal ThicknessPermissible Variations, AverageContinuou
47、sStaple(discontinuous)millimetres0.125 and under 60.013 .Over 0.125 to 0.250 60.025 60.050Over 0.250 to 0.380 60.050 60.075Over 0.380 to 0.025 . 60.075inches0.0050 and under 60.0005 .Over 0.0050 to 0.0100 60.0010 60.0020Over 0.0100 to 0.0150 60.0020 60.0030Over 0.0150 to 0.0250 . 60.0030Permissible
48、Variations, IndividualContinuousStaple(discontinuous)millimetres0.125 and under 60.025 .Over 0.125 to 0.250 60.040 60.075Over 0.250 to 0.380 60.060 60.090Over 0.380 to 0.635 . 60.090inches0.0050 and under 60.0010 .Over 0.0050 to 0.0100 60.0015 60.0030Over 0.0100 to 0.0150 60.0025 60.0035Over 0.0150
49、to 0.0250 . 60.0035TABLE 6 TolerancesTape WidthNominal Tape Width,mm in.Permissible Variation,mm in.Less than 25.4 1.0 60.8 132Over 25.4 1.0 61.6 116D580/D580M 10419. Ignition Loss19.1 The organic content of greige tape or webbing shall beless than 4.0 % unless otherwise agreed upon between thepurchaser and the supplier.20. Visual Appearance20.1 The woven greige tape or webbing shall be generallyuniform in quality and condition, clean, smooth, and free offoreign particles and from defects detrimental to fabricatio
