1、Designation: D 4900 99 (Reapproved 2009)Standard Test Method forLignosulfonates (Sulfite Cellulose) in Tanning Extracts1This standard is issued under the fixed designation D 4900; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the
2、 year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method is intended for use in detecting thepresence of lignosulfonates (sulfite cellulose) in extra
3、cts oftanning materials.1.2 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this st
4、andard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D 4901 Practice for Preparation of Solution of Liquid Veg-etable Tannin ExtractsD 4905 Practice for Preparation of Solution
5、of Solid, Pastyand Powdered Vegetable Tannin ExtractsD 6404 Practice for Sampling Vegetable Materials Contain-ing TanninD 6405 Practice for Extraction of Tannins from Raw andSpent Materials2.2 ALCA Methods:A50 Lignosulfonates (Sulfite Cellulose)33. Summary of Test Method3.1 The reaction with aniline
6、, of a tanning material extractspecimen is compared with that of a solution containinglignosulfonate and tanning material known to be free fromlignosulfonate.4. Significance and Use4.1 The test method is useful to detect possible adulterationof tanning material extract with cheap and inferior lignos
7、ul-fonates.5. Specimen5.1 The sample shall be drawn as described in PracticeD 6404.5.2 The specimen shall consist of 5 mL of a solution ofanalytical strength (4.0 g tannin per L), prepared as describedin Practices D 4901, D 4905, and Practice D 6405.6. Apparatus and Reagents6.1 Aniline.6.2 Hydrochlo
8、ric Acid, concentrated.6.3 Comparison SolutionThis shall contain lignosulfonate(sulfite cellulose) in the proportion of 1 g total solids to 2000mL of solution, and as much tanning material, similar to and ofthe same type as that being tested but known to be free fromlignosulfonate, as will make up t
9、he solution to analyticalstrength.7. Procedure7.1 Place the specimen in a test tube. Add 0.5 mL of aniline,and shake well. Add 2 mL of concentrated hydrochloric acid,and again shake mixture well.8. Results8.1 If at least as much precipitate remains at the end of 15min as is obtained when the compari
10、son solution is similarlytreated, the material shall be held to contain lignosulfonates(sulfite cellulose) and the fact shall be noted on the analysisreport.8.2 Attention is drawn to the fact that some synthetictannins give precipitates under the conditions of this testmethod.9. Precision and Bias9.
11、1 This test method is adopted from the procedures of theAmerican Leather Chemists Association3where it has longbeen in use and where it was approved for publication beforethe inclusion of precision and bias statements were mandated.The original interlaboratory test data is no longer available.1This
12、test method is under the jurisdiction of ASTM Committee D31 on Leatherand is the direct responsibility of Subcommittee D31.01 on Vegetable Leather Thistest method has been adapted from and is a replacement for Method A50 of theOfficial Methods of the American Leather Chemists Association.Current edi
13、tion approved April 1, 2009. Published July 2009. Originallyapproved in 1989. Last previous edition approved in 2004 as D 4900 99 (2004).2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume i
14、nformation, refer to the standards Document Summary page onthe ASTM website.3Official Methods of the American Leather Chemists Association. Availablefrom the American Leather Chemists Association, University of Cincinnati, P.O.Box 210014, Cincinnati, OH 452210014.1Copyright ASTM International, 100 B
15、arr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.The user is cautioned to verify by the use of referencematerials, if available, that the precision and bias of this testmethod is adequate for the contemplated use.10. Keywords10.1 lignosulfonates; sulfite cellulose; tann
16、in analysis; veg-etable tannin analysisASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the
17、riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of
18、this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldma
19、ke your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).D 4900 99 (2009)2
