1、Designation: D 6957 03Standard Practice forMeasuring Curl in Paint Brush Filling Material1This standard is issued under the fixed designation D 6957; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A numb
2、er in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice describes the procedure for measuring curlin synthetic filament.1.2 This practice is applicable to filament 2 to 5 in. (50.8
3、 to127 mm) in length.1.3 This practice is applicable to tapered filament or levelfilament.1.4 The values given in-pound units are to be regarded asthe standard as this is the dominant measurement system usedin the paint brush industry. The values given in parentheses arefor information only.1.5 This
4、 standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Terminology2.1 Defin
5、itions of Terms Specific to This Standard:2.1.1 paint brush filament, na synthetic polymer extrusionused in brushing material.2.1.2 filament curl, ndeviation from straight, along thelength of a filament.2.1.3 butt-end, nthe larger end of a tapered filament;either end of a level filament.3. Significa
6、nce and Use3.1 It is important for the manufacturing and performance ofa brush to have filaments with minimal curl.4. Apparatus4.1 Filament curl deviation chart. See Fig. 1.5. Procedure5.1 For Testing Synthetic Filaments:5.1.1 Select filaments to be measured.5.1.2 Allow filaments to acclimate to roo
7、m temperature 70to 75F (21 to 24C) at least two h.5.1.3 Place a filament on the filament curl deviation chartwith butt-end at the x-reference point (see Fig. 1).5.1.4 Record the degree of deviation from straight at theother end of the filament.5.1.5 If multiple filaments of the same type and length
8、are tobe measured, repeat 5.1.3 and 5.1.5 for each of the remainingfilaments and average the results.6. Keywords6.1 curl; filament1This practice is under the jurisdiction of ASTM Committee D01 on Paint andRelated Coatings, Materials, and Applications and is the direct responsibility ofSubcommittee D
9、01.61 on Paint Application Tools.Current edition approved Oct. 1, 2003. Published October 2003.FIG. 1 Filament Curl Deviation Chart1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.ASTM International takes no position respecting the va
10、lidity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is su
11、bject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headqu
12、arters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This stand
13、ard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).D6957032
