1、Designation: F2763 11F2763 16Standard Specification for3012 to 60 in. 750300 to 1500 mm Dual and Triple Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary SewerApplications1This standard is issued under the fixed designation F2763; the number immediately following the designation indicate
2、s the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers requirements and tes
3、t methods for dual and triple profile wall polyethylene pipe and fittings. Thenominal inside diameters covered are 3012 to 60 in. 750300 to 1500 mm.1.2 The requirements of this specification are intended to provide pipe and fittings suitable for underground use for non-pressuresanitary sewer systems
4、. Pipe and fittings produced in accordance with this specification shall be installed in compliance withPractice D2321.1.3 This specification covers pipe and fittings with an essentially smooth interior and wall and either an annular corrugation(dual wall) or an essentially smooth and exterior wall
5、using an annular corrugated profile middle wall (triple wall) (Fig. 1).1.4 UnitsThe values stated in either SI units or inch-pound units are to be regarded separately as standard. The values statedin each system may not be exact equivalents; therefore, each system shall be used independently of the
6、other. Combining valuesfrom the two systems may result in non-conformance with the standard.1.5 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification. This standarddoes not purport to address all of the safety concerns, if any, associated with
7、its use. It is the responsibility of the user of thisstandard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D578/D578M Specification for Glass Fiber StrandsA666 Specification for
8、Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat BarD618 Practice for Conditioning Plastics for TestingD1600 Terminology for Abbreviated Terms Relating to PlasticsD2122 Test Method for Determining Dimensions of Thermoplastic Pipe and FittingsD2321 Practice for Undergr
9、ound Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow ApplicationsD2412 Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate LoadingD2444 Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Me
10、ans of a Tup (FallingWeight)D3212 Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric SealsD3350 Specification for Polyethylene Plastics Pipe and Fittings MaterialsD4218 Test Method for Determination of Carbon Black Content in Polyethylene Compounds By the Muffle-Fu
11、rnace TechniqueD4389 Specification for Finished Glass Fabrics Woven From RovingsF412 Terminology Relating to Plastic Piping SystemsF477 Specification for Elastomeric Seals (Gaskets) for Joining Plastic PipeF2136 Test Method for Notched, Constant Ligament-Stress (NCLS) Test to Determine Slow-Crack-Gr
12、owth Resistance of HDPEResins or HDPE Corrugated Pipe1 This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.62 on Sewer.Current edition approved Feb. 1, 2011Feb. 1, 2016. Published February 2011April 2016. O
13、riginally approved in 2011. Last previous edition approved in 2011 as F276311.DOI: 10.1520/F276311.10.1520/F276316.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to th
14、e standards Document Summary page on the ASTM website.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes ac
15、curately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United S
16、tates12.2 AASHTO Standard:3LRFD, Section 12 AASHTO LRFD Bridge Design Specifications Section 12 Buried Structures and Tunnel Liners2.3 Federal Standards:4Fed. Std. No. 123 Marking for Shipment (Civil Agencies)MIL-STD-129 Marking for Shipment and Storage2.4 NCHRP (National Cooperative Highway Researc
17、h Program) Report:4NCHRP Report 631 Updated Test and Design Methods for Thermoplastic Drainage Pipe3. Terminology3.1 DefinitionsDefinitions are in accordance with Terminology F412 and abbreviations are in accordance with TerminologyD1600, unless otherwise specified. The abbreviation for polyethylene
18、 is PE.3.2 Definitions of Terms Specific to This Standard:3.2.1 annular corrugationcorrugation formed in a circumferential pattern around the pipe as opposed to a helical corrugation,which is formed in a spiral pattern around the pipe.3.2.2 dual wall, nin this case, the profile pipe wall constructio
19、n provides an interior liner in the waterway and includes ribs,corrugations, or other shapes, which can be either solid or hollow, that helps brace the pipe against diametrical deformation. Thecorrugation wall is exposed to the soil side of the pipe and is its exterior wall.3.2.3 triple wall, nInin
20、this case, the profile pipe wall construction provides an interior wall in the waterway, an exterior wallto the soil, and includes ribs, corrugations, or other shapes, which can be either solid or hollow, that helps brace the pipe againstdiametrical deformation. The corrugation wall is completely en
21、capsulated by the interior and exterior walls.4. Ordering Information4.1 Orders for product made to this specification shall include the following information to adequately describe the desiredproduct4.1.1 This ASTM designation (F2763) and year of issue,4.1.2 Diameters,4.1.3 Total footage of each pi
22、pe diameter involved,4.1.4 Pipe laying length,4.1.5 Fitting type(s):3 Available from American Association of State Highway and Transportation Officials (AASHTO), 444 N. Capitol St., NW, Suite 249, Washington, DC 20001,http:/www.transportation.org.4 Available from Standardization Documents Order Desk
23、, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http:/dodssp.daps.dla.mil.DLADocument Services Building 4/D 700 Robbins Avenue Philadelphia, PA 19111-5094 http:/quicksearch.dla.mil/FIG. 1 Typical Dual and Triple Wall Pipe ProfileF2763 1624.1.5.1 Size and type of fittings
24、, including mainline and branch diameters, and4.1.5.2 Number of fittings per diameter.5. Materials and Manufacture5.1 Pipe and Fabricated FittingsThe pipe and fabricated fittings shall be made of virgin PE material meeting the requirementsof Specification D3350 with a minimum cell classification of
25、435400C, except that carbon black content shall equal to or greaterthan 2.0% but not exceed 3.0 % when tested in accordance with D4218. Materials that have a higher cell classification in one ormore properties shall be permitted provided all other product requirements are met.5.2 Rework MaterialClea
26、n rework material generated from the manufacturers own pipe and fittings production of thisproduct shall be permitted to be used by the same manufacturer. Rework shall be the same cell classification as new PE compoundwith which it is blended and the pipe produced shall meet all the requirements of
27、this specification.6. General Requirements6.1 WorkmanshipThe pipe and fittings shall be homogeneous throughout and be as uniform as commercially practical in color,opacity, and density. The pipe walls shall be free of cracks, holes, blisters, voids, foreign inclusions, or other defects that are visi
28、bleto the naked eye and that may affect the wall integrity. The ends shall be cut cleanly and squarely through valleys.6.1.1 Visible defects, cracks, creases, splits, in pipe are not permissible.6.2 Dimensions and Tolerance:6.2.1 Nominal SizeThe nominal size for the pipe and fittings shall be the in
29、side diameter shown in Table 1.NOTE 1The outside diameters of products manufactured to this specification are not specified; therefore, compatibility between pipe and fittings madeto this specification from different manufacturers must be verified.6.2.2 Minimum Inside DiameterThe minimum inside diam
30、eter shall be as shown in Table 1, when measured in accordancewith 7.3.1.6.2.3 LengthThe pipe shall be supplied in any length agreeable to both the owner and the manufacturer. Length shall not beless than 99 % of stated quantity when measured in accordance with 7.3.2.6.2.4 Minimum Wall, Crown, Valle
31、y and Liner ThicknessThe minimum thickness of the pipe wall, crown, valley and linersshall meet the requirements given in Table 1 when measured in accordance with 7.3.3.6.3 Pipe StiffnessMinimum pipe stiffness at 5 % deflection shall meet the requirements given in Table 1 when tested inaccordance wi
32、th 7.4.NOTE 2The 5 % deflection criterion, which was selected for testing convenience, is not a limitation with respect to in-use deflection. The engineeris responsible for establishing the acceptable deflection limit.TABLE 1 Pipe Stiffness and Pipe DimensionsPipeInsideDiameterMinimumInsideDiameterA
33、InsideDiameterTolerancesMinimumPipe Stiffnessat 5 % DeflectionMinimumInner LinerThicknessMinimumOuterLinerThicknessMinimumValleyThicknessMinimumCrownThicknessPipeInsideDiameterAMinimumInsideDiameterBInsideDiameterTolerancesMinimumPipe Stiffnessat 5 % DeflectionMinimumInner LinerThicknessMinimumOuter
34、LinerThicknessMinimumValleyThicknessMinimumCrownThicknessin. mm in. mm in. mm lb/in./in.kPa in. mm in. mm in. mm in. mm12 300 11.90 302 +0.11/-0.11 +3.0/-3.0 46 317 0.043 1.1 . . 0.048 1.2 0.072 1.815 375 14.85 377 +0.11/-0.11 +3.0/-3.0 46 317 0.052 1.3 . . 0.065 1.7 0.103 2.618 450 17.93 455 +0.14/
35、-0.14 +4.0/-4.0 46 317 0.060 1.5 . . 0.072 1.8 0.105 2.721 525 20.75 527 +0.15/-0.15 +4.0/-4.0 46 317 0.062 1.6 . . 0.079 2.0 0.116 2.924 600 23.90 607 +0.16/-0.16 +4.0/-4.0 46 317 0.064 1.6 . . 0.086 2.2 0.127 3.227 675 26.75 679 +0.17/-0.17 +4.0/-4.0 46 317 0.073 1.9 . . 0.088 2.2 0.130 3.330 750
36、29.79 757 +0.18/-0.18 +5.0/-5.0 46 317 0.086 2.2 . . 0.093 2.4 0.132 3.430 750 29.62 752 +0.18/- 0.18 +4.6/-4.6 46 317 0.070 1.8 0.070 1.8 0.089 2.3 0.127 3.236 900 35.40 899 +0.21/- 0.21 +5.3/-5.3 46 317 0.095 2.4 0.095 2.4 0.120 3.0 0.182 4.642 1050 41.31 1049 +0.22/- 0.22 +5.6/-5.6 46 317 0.105 2
37、.7 0.105 2.7 0.133 3.4 0.182 4.648 1200 47.31 1201 +0.27/- 0.27 +6.9/-6.9 46 317 0.105 2.7 0.105 2.7 0.139 3.5 0.187 4.854 1350 53.32 1354 +0.27/- 0.27 +6.9/-6.9 46 317 0.100 2.8 0.110 2.8 0.144 3.7 0.187 4.860 1500 59.30 1506 +0.31/- 0.31 +7.9/-7.9 46 317 0.115 2.9 0.115 2.9 0.151 3.8 0.231 5.9AThe
38、 triple wall profile wall pipe are only available in sizes 30 in 750 mm to 60 in 1500 mm. Dual wall profile pipe are available in sizes 12 in 300 mm to 30 in 750mm. At 30 in 750 mm diameter, where the dimensions for the outer liner thickness are defined, all the associated dimensions shall only pert
39、ain to the triple wall profilepipe.B The manufacturers stated inside diameter is the diameter plus or minus the inside diameter tolerance. In no case shall the manufacturers minimum diameter with thetolerance be less than the minimum as shown in Table 1.F2763 1636.4 Pipe FlatteningThere shall be no
40、evidence of splitting, cracking, breaking, separation of seams, separation of the outerand inner wall, or combinations thereof, when conditioned in accordance with 7.2 and tested in accordance with 7.5.6.5 Pipe Impact StrengthThere shall be no evidence of splitting, cracking, breaking, separation of
41、 seams, separation of theouter and inner wall, or combinations thereof, when tested in accordance with 7.6 and examined under normal light and the unaidedeye.6.6 Fittings and Joining Systems:6.6.1 Only fittings fabricated from pipe made to this standard and supplied Fittings shall be fabricated by t
42、he pipe manufacturershall be used. Fittings shall be installed from pipe made in accordance with the manufacturers recommendations and must meetthe same material this standard. Fittings fabricated from dual-wall pipe shall be used with dual-wall pipe. Fittings fabricated fromtriple-wall pipe shall b
43、e used with triple-wall pipe. Fitting material shall comply with 5.1 and 5.2performance requirements as thepipeNOTE 3The fittings may be fabricated from the pipe by a variety of processes including hot plate welding, spin welding or other processes.6.6.1.1 Fittings shall be parallel-plate load teste
44、d. Fittings shall be tested in an installation orientation, shall be uniformlysupported (body and outlet(s) by the lower plate, and uniformly loaded (body and outlet(s) by the upper plate. Fittings shall meetor exceed a vertical load equivalent to the 5% deflection stiffness in accordance with Table
45、 1 for pipe to which the fitting is to bejoined. The equivalent maximum load shall be the 5% deflection stiffness in accordance with Table 1 unit load (psi/in or kPa /mm)multiplied by the length of the fitting (run plus branch(es) as applicable) that is loaded by the upper plate. Testing shall be fo
46、requivalent load, not deflection. Acceptance criteria shall be in accordance with 6.4.NOTE 4Installation orientation means that the fitting testing orientation is as though it were installed in a pipeline, for example, an elbow or tee withthe directional outlet(s) to the side. In accordance with an
47、established quality program, fittings should be tested to only qualify the overall design andintegrity of the unit. As unique structures, testing of every angle orientation is not necessary.6.6.1.2 The fitting body in an installation orientation shall be impact tested in accordance with 7.6. Accepta
48、nce criteria shall bein accordance with 6.5.6.6.2 The joining system(s) between pipe and between pipe and fittings shall be of a design that preserves pipeline slope andalignment during construction and prevents separation at the joints.6.6.3 Pipe and fittings shall have a watertight bell/spigot joi
49、nt that complies with the laboratory tests defined and described inTest Method D3212 and utilizes a gasket that complies with the requirements of Specification F477. Note that special provisionsmust be taken in order to join field cut pipe that meets the requirements of Test Method D3212.Any component used in the joiningmaterial shall be resistant to
