1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationSafety of woodworking machines Circular sawing machinesPart 8: Single blade edging circular rip sawing machines with power driven saw unit and manual loading and/or unloadingBS E
2、N 1870-8:2012Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-National forewordThis British Standard is the UK implementation of EN 1870-8:2012. It super-sedes BS EN 1870-8:2001+A
3、1:2009 which is withdrawn.The UK participation in its preparation was entrusted to Technical CommitteeMTE/23, Woodworking machines.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provision
4、s of acontract. Users are responsible for its correct application. The British Standards Institution 2012Published by BSI Standards Limited 2012ISBN 978 0 580 72425 1ICS 79.120.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under
5、 the authority of the StandardsPolicy and Strategy Committee on 31 January 2013.Amendments issued since publicationAmd. No. Date Text affectedBRITISH STANDARDBS EN 1870-8:2012Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or netwo
6、rking permitted without license from IHS-,-,-EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1870-8 November 2012 ICS 79.120.10 Supersedes EN 1870-8:2001+A1:2009English Version Safety of woodworking machines - Circular sawing machines - Part 8: Single blade edging circular rip sawing machines w
7、ith power driven saw unit and manual loading and/or unloading Scurit des machines pour le travail du bois - Machines scies circulaires - Partie 8: Dligneuses mono-lames dplacement mcanis du groupe de sciage et chargement et/ou dchargement manuel Sicherheit von Holzbearbeitungsmaschinen - Kreissgemas
8、chinen - Teil 8: Einblattbesum- und Leistenkreissgemaschinen mit kraftbettigtem Sgeaggregat und Handbeschickung und/oder Handentnahme This European Standard was approved by CEN on 1 September 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditio
9、ns for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in
10、 three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standard
11、s bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Sloven
12、ia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for
13、 CEN national Members. Ref. No. EN 1870-8:2012: EBS EN 1870-8:2012Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EN 1870-8:2012 (E) 2 Contents Page Foreword 4Introduction .61 Sc
14、ope 72 Normative references 73 Terms and definitions .94 List of significant hazards . 135 Safety requirements and/or measures . 165.1 General . 165.2 Controls . 165.2.1 Safety and reliability of control systems 165.2.2 Position of controls 175.2.3 Starting 175.2.4 Normal stopping . 185.2.5 Emergenc
15、y stop 195.2.6 Integrated feed 195.2.7 Saw blade changing . 205.2.8 Speed control 205.2.9 Control duplication . 205.2.10 Failure of the power supply . 205.2.11 Powered movement of the saw blade and/or fences 215.3 Protection against mechanical hazards . 225.3.1 Stability 225.3.2 Risk of break-up dur
16、ing operation 225.3.3 Tool holder and tool design . 235.3.4 Braking . 245.3.5 Devices to minimise the possibility or the effect of ejection . 255.3.6 Workpiece supports and guides . 305.3.7 Prevention of access to moving parts 315.3.8 Workpiece clamping . 335.3.9 Safety appliances 355.4 Protection a
17、gainst non-mechanical hazards . 355.4.1 Fire . 355.4.2 Noise 355.4.3 Emission of chips and dust . 365.4.4 Electricity . 375.4.5 Ergonomics and handling 375.4.6 Lighting 385.4.7 Pneumatic 385.4.8 Hydraulic 385.4.9 Electromagnetic compatibility . 385.4.10 Laser 385.4.11 Errors of fitting 395.4.12 Isol
18、ation . 395.4.13 Maintenance 396 Information for use . 406.1 General . 406.2 Warnings and warning devices . 406.3 Marking 40BS EN 1870-8:2012Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license fr
19、om IHS-,-,-EN 1870-8:2012 (E) 3 6.3.1 Marking of riving knives . 406.3.2 Marking of machine . 406.4 Instruction handbook 41Annex A (normative) Saw spindle dimensional tolerances 45Annex B (normative) Riving knife mounting strength test . 46Annex C (normative) Lateral stability riving knife test . 47
20、Annex D (normative) Sectional safety curtain material rigidity test 48Annex E (normative) Operating conditions for noise emission measurement 49E.1 General . 49E.2 Noise measurements 49E.3 General data sheet 51Annex F (normative) Braking tests . 55F.1 Conditions for all tests 55F.2 Tests . 55F.2.1 U
21、n-braked run-down time . 55F.2.2 Braked run-down time . 55Annex G (normative) Impact test method for guards . 56G.1 General . 56G.2 Test method . 56G.2.1 Preliminary remarks 56G.2.2 Testing equipment . 56G.2.3 Projectile for guards 56G.2.4 Sampling. 56G.2.5 Test procedure . 56G.3 Results 57G.4 Asses
22、sment . 57G.5 Test report 57G.6 Test equipment for impact test 57Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC 59Bibliography 60BS EN 1870-8:2012Copyright European Committee for Standardization Provided by IHS under licen
23、se with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EN 1870-8:2012 (E) 4 Foreword This document (EN 1870-8:2012) has been prepared by Technical Committee CEN/TC 142 “Woodworking machines - Safety”, the secretariat of which is held by UNI. This European Stand
24、ard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2013, and conflicting national standards shall be withdrawn at the latest by May 2013. Attention is drawn to the possibility that some of the elements of this docu
25、ment may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 1870-8:2001+A1:2009. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Tra
26、de Association, and supports essential requirements of the Machinery Directive. For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. The main modifications to the previous version concern inclusion of performance levels (PL). Organisations cont
27、ributing to the preparation of this European Standard include European Committee of Woodworking Machinery Manufacturers Association “EUMABOIS“. EN 1870 Safety of woodworking machines Circular sawing machines consists of the following parts: Part 1: Circular saw benches (with and without sliding tabl
28、e), dimension saws and building site saws; Part 3: Down cutting cross-cut saws and dual purpose down cutting cross-cut saws/circular saw benches; Part 4: Multiblade rip sawing machines with manual loading and/or unloading; Part 5: Circular sawbenches/up-cutting cross-cut sawing machines; Part 6: Cir
29、cular sawing machines for firewood and dual purpose circular sawing machines for firewood/circular saw benches, with manual loading and/or unloading; Part 7: Single blade log sawing machines with integrated feed table and manual loading and/or unloading; Part 8: Single blade edging circular rip sawi
30、ng machines with power driven saw unit and manual loading and/or unloading (the present document); Part 9: Double blade circular sawing machines for cross-cutting with integrated feed and with manual loading and/or unloading; Part 10: Single blade automatic and semi-automatic up-cutting cross-cut sa
31、wing machines; Part 11: Semi-automatic and automatic horizontal cross-cut sawing machines with one saw unit (radial arm saws); Part 12: Pendulum cross-cut sawing machines; Part 13: Horizontal beam panel sawing machines; BS EN 1870-8:2012Copyright European Committee for Standardization Provided by IH
32、S under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EN 1870-8:2012 (E) 5 Part 14: Vertical panel sawing machines; Part 15: Multi-blade cross-cut sawing machines with integrated feed of the workpiece and manual loading and/or unloading; Part 16:
33、Double mitre sawing machines for V-cutting; Part 17: Manual horizontal cutting cross-cut sawing machines with one saw unit (manual radial arm saws); Part 18: Dimension saws (at Formal Vote stage at the time of publication of the present document); Part 19: Circular saw benches (with and without slid
34、ing table) and building site saws (at Enquiry stage at the time of publication of the present document). The European Standards produced by CEN/TC 142 are particular to woodworking machines and complement the relevant A and B Standards on the subject of general safety (see Introduction of EN ISO 121
35、00:2010 for a description of A, B and C standards). According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland
36、, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 1870-8:2012Copyright European
37、 Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EN 1870-8:2012 (E) 6 Introduction This document has been prepared to be a harmonised standard to provide one means of conforming to the essential sa
38、fety requirements of the Machinery Directive, and associated EFTA regulations. This document is a type “C” standard as defined in EN ISO 12100:2010. The machinery concerned and the extent to which hazards, hazardous situations and events covered are indicated in the scope of this document. The requi
39、rements of this document are directed to manufacturers and their authorised representatives of single blade edging circular rip sawing machines with power driven saw unit and manual loading and/or unloading. This document is also useful for designers and importers. When provisions of this type C sta
40、ndard are different from those which are stated in type A or B standards, the provisions of this type C standard take precedence over the provisions of other standards, for machines that have been designed and built according to the provisions of this type C standard. This document also includes inf
41、ormation to be provided by the manufacturer to the user. Common requirements for tooling are given in EN 847-1:2005+A1:2007. BS EN 1870-8:2012Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license f
42、rom IHS-,-,-EN 1870-8:2012 (E) 7 1 Scope This European Standard deals with all significant hazards, hazardous situations and events as listed in Clause 4 which are relevant to single blade edging circular rip sawing machines with power driven saw unit and manual loading and/or unloading, hereinafter
43、 referred to as “machines”, designed to cut solid wood, chipboard, fibreboard and plywood when they are used as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. This document applies to machines where the workpiece is stationary, the vertical an
44、d horizontal movements of the saw unit are power driven, and where the machine is provided with workpiece clamping. The workpiece may or may not be clamped during cutting. This document does not apply to machines: where the workpiece is fed to the saw blade during cutting; designed for cutting venee
45、rs; provided with a device situated behind the line of cut, which moves in a direction parallel to the line of cut, for automatically unloading the workpiece during the return of the saw unit to the rest position. This document is not applicable to machines manufactured before its date of publicatio
46、n as EN. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including
47、any amendments) applies. EN 349:1993+A1:2008, Safety of machinery Minimum gaps to avoid crushing of parts of the human body EN 614-1:2006+A1:2009, Safety of machinery Ergonomic design principles Part 1: Terminology and general principles EN 614-2:2000+A1:2008, Safety of machinery Ergonomic design principles Part 2: Interactions between the design of machinery and work tasks EN 847-1:2005+A1:2007, Tools for woodworking Safety requirements Part 1: Milling tools, circular saw blades EN 894-1:1997+A1:2008, Safety of machinery Ergonomics requirements for the design of
