BS EN 28736-1992 Taper pins with internal thread unhardened《未淬硬的内螺纹锥型销》.pdf
《BS EN 28736-1992 Taper pins with internal thread unhardened《未淬硬的内螺纹锥型销》.pdf》由会员分享,可在线阅读,更多相关《BS EN 28736-1992 Taper pins with internal thread unhardened《未淬硬的内螺纹锥型销》.pdf(12页珍藏版)》请在麦多课文档分享上搜索。
1、BRITISH STANDARD BS EN 28736:1992 ISO8736:1986 Taper pins with internal thread, unhardened The European Standard EN28736:1992 has the status of a BritishStandardBSEN28736:1992 This BritishStandard, having been prepared under the directionof the General Mechanical Engineering Standards Policy Committ
2、ee, waspublished under the authorityof the Standards Boardand comes into effect on 15 October1992 BSI12-1999 The following BSI references relate to the work on this standard: Committee reference GME/9 Draft for comment85/73840DC ISBN 0 580 21315 3 Cooperating organizations The European Committee for
3、 Standardization (CEN), under whose supervision this European Standard was prepared, comprises the national standards organizations of the following countries: Austria Oesterreichisches Normungsinstitut Belgium Institut belge de normalisation Denmark Dansk Standardiseringsraad Finland Suomen Standar
4、disoimisliito, r.y. France Association franaise de normalisation Germany Deutsches Institut fr Normung e.V. Greece Hellenic Organization for Standardization Iceland Technological Institute of Iceland Ireland National Standards Authority of Ireland Italy Ente Nazionale Italiano di Unificazione Luxemb
5、ourg Inspection du Travail et des Mines Netherlands Nederlands Normalisatie-instituut Norway Norges Standardiseringsforbund Portugal Instituto Portugus da Qualidade Spain Asociacin Espaola de Normalizacin y Certificacin Sweden Standardiseringskommissionen i Sverige Switzerland Association suisse de
6、normalisation United Kingdom BritishStandards Institution Amendments issued since publication Amd. No. Date CommentsBSEN28736:1992 BSI 12-1999 i Contents Page Cooperating organizations Inside front cover National foreword ii Foreword 2 1 Scope and field of application 3 2 References 3 3 Dimensions 4
7、 4 Specifications and reference International Standards 5 5 Designation 5 National annex NA (informative) Committees responsible Inside back cover National annex NB (informative) Cross-reference Inside back coverBSEN28736:1992 ii BSI 12-1999 National foreword This BritishStandard has been prepared u
8、nder the direction of the General Mechanical Engineering Standards Policy Committee and is the English language version of EN28736:1992 Taper pins with internal thread, unhardened, published by the European Committee for Standardization (CEN). It is identical with ISO8736:1986, published by the Inte
9、rnational Organization for Standardization (ISO). EN28736:1992 was produced as a result of international discussion in which the UK took an active part. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their cor
10、rect application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, theEN title page, pages2 to6, an inside back cover and a back cover. This standard has been upd
11、ated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN28736 July1992 UDC621.886.115 Descriptors: Fasteners, locating pins, taper pins, specifications, dimensions,
12、 designation English version Taper pins with internal thread, unhardened (ISO8736:1986) Goupilles de position coniques trou taraud, non trempes (ISO8736:1986) Kegelstifte mit Innengewinde, ungehrtet (ISO8736:1986) This European Standard was approved by CEN on1992-07-17. CEN members are bound to comp
13、ly with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Sec
14、retariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the off
15、icial versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de
16、 Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1992 Copyright reserved to CEN members Ref.No.EN28736:1992EEN28736:1992 BSI 12-1999 2 Foreword In1992, CEN Technical Committee CEN/TC185 “Threaded and non threaded mechanical fasteners and accessor
17、ies” the secretariat of which is held by DIN decided to submit the International Standard ISO8736:1986 “Taper pins with internal thread, unhardened” to the formal vote procedure. The result was positive. In the countries bound to implement this EuropeanStandard a national standard identical to this
18、European Standard shall be published at the latest by1993-01-31 and conflicting national standards shall be withdrawn at the latest by1993-01-31. According to the CEN/CENELEC Common Rules the following countries are bound to implement this EuropeanStandard: Austria, Belgium, Denmark, Finland, France
19、, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Spain, Portugal, Sweden, Switzerland and UnitedKingdom.EN28736:1992 BSI 12-1999 3 1 Scope and field of application This International Standard specifies the characteristics of unhardened taper pins with internal thread, and
20、 metric dimensions and nominal diameters, d 1 , from6 to50mm inclusive. 2 References ISO965, ISO general purpose metric screw threads Tolerances. ISO2081, Metallic coatings Electroplated coatings of zinc on iron or steel. ISO3269, Fasteners Acceptance inspection. ISO4520, Chromate conversion coating
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
本资源只提供5页预览,全部文档请下载后查看!喜欢就下载吧,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BSEN287361992TAPERPINSWITHINTERNALTHREADUNHARDENED 未淬硬 螺纹 锥型销 PDF

链接地址:http://www.mydoc123.com/p-574393.html